Power Source Control
- Stop Light Switch
- Shift P Signal
- Neutral SW/ Clutch SW
- Starter Relay Driving Request (Starting Control)
- Starter Relay
- Power Supply Condition
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000026DZB |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, except TMMMS Made)): Engine does not Start; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022] | ||
|
Engine does not Start |
DESCRIPTION
except Manual Transaxle
-
When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift position is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift position in N and the brake pedal depressed.
Related Data List and Active Test Items
Problem Symptom
Data List and Active Test
Engine does not start
Smart Key
- Immobiliser
- Start Request
- L Code Check
- S Code Check
for Manual Transaxle
-
When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the clutch pedal is depressed, the engine can be started by pressing the engine switch.
Related Data List and Active Test Items
Problem Symptom
Data List and Active Test
Engine does not start
Power Source Control
- Neutral SW/ Clutch SW
- Starter Relay Driving Request (Starting Control)
- Starter Relay
- Power Supply Condition
Smart Key
- Immobiliser
- Start Request
- L Code Check
- S Code Check
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins.
Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Start Key(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
-
The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.
Click here
![2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, except TMMMS Made)): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
-
If the smart key system (for Start Function) has been disabled, enable the system before performing troubleshooting.
Click here
- Inspect the fuses of circuits related to this system before performing the following procedure.
-
Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to Registration.
Click here
- After completing repairs, confirm that the problem does not recur.
- After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
HINT:
- If the ignition switch is changed from ON to ACC with the shift position in any position other than P, and then the shift position is moved to P and the engine switch is pressed with the brake pedal depressed, the ignition switch will turn off.*
-
If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure will be released and the force required to depress the brake pedal to illuminate the stop lights will increase.*
- *: except Manual Transaxle
PROCEDURE
|
1. |
CHECK WHETHER ENGINE STARTS |
(a) Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the ignition switch to ON.
(b) Check that the engine can be started 5 seconds after the ignition switch turned to ON.
OK:
Engine starts normally.
| OK |
|
|
|
2. |
CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET) |
(a) Get into the vehicle while carrying an electrical key transmitter sub-assembly.
(b) Move the shift position to P.*1
(c) Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.*1
(d) Press the engine switch with the clutch pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.*2
OK:
The security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.
HINT:
The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.
- *1: except Manual Transaxle
- *2: for Manual Transaxle
| NG |
|
GO TO OTHER PROBLEM (Immobiliser System does not Operate Properly) |
|
|
3. |
CHECK FOR DTC |
(a) Using the GTS, check if LIN communication DTC B278588 and B278987 are output.
Body Electrical > Smart Key > Trouble Codes
OK:
DTC B278588 and B278987 are not output.
| NG |
|
|
|
4. |
CHECK ENGINE CRANKING OPERATION |
(a) Get into the vehicle while carrying an electrical key transmitter sub-assembly.
(b) Move the shift position to P.*1
(c) Depressed the brake pedal.*1
(d) Depressed the clutch pedal.*2
- *1: except Manual Transaxle
- *2: for Manual Transaxle
(e) Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch and check that the engine cranks.
|
Result |
Proceed to |
|---|---|
|
Engine cranks and initial combustion occurs |
A |
|
Engine cranks but initial combustion does not occur |
B |
|
Engine does not crank |
C |
| A |
|
GO TO OTHER PROBLEM (Immobiliser System does not Operate Properly) |
| B |
|
GO TO SFI SYSTEM for M20A-FKS: Click here
for G16E-GTS: Click here
|
|
|
5. |
CHECK ENGINE SWITCH CONDITION |
(a) Get into the vehicle while carrying an electrical key transmitter sub-assembly.
(b) Move the shift position to P.*1
(c) With the brake pedal released, check that pressing the engine switch causes the power source mode to change.*1
(d) With the clutch pedal released, check that pressing the engine switch causes the power source mode to change.*2
- *1: except Manual Transaxle
- *2: for Manual Transaxle
|
Result |
Proceed to |
|---|---|
|
Power source mode changes : Off → ACC → ON → off (except Manual Transaxle) |
A |
|
Power source mode changes : Off → ACC → ON → off (for Manual Transaxle) |
B |
|
Power source mode does not change to ACC or ON |
C |
|
Power source mode changes to ON but not to ACC |
D |
|
Power source mode changes to ACC but not to ON |
E |
| B |
|
| C |
|
GO TO OTHER PROBLEM (Power Source Mode does not Change to ON (IG and ACC)) |
| D |
|
GO TO OTHER PROBLEM (Power Source Mode does not Change to ON (ACC)) |
| E |
|
GO TO OTHER PROBLEM (Power Source Mode does not Change to ON (IG)) |
|
|
6. |
READ VALUE USING GTS (STOP LIGHT SWITCH1) |
(a) Read the Data List according to the display on the GTS.
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Stop Light Switch |
State of brake pedal |
OFF or ON |
OFF: Brake pedal released ON: Brake pedal depressed |
|
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Stop Light Switch |
OK:
The GTS display changes correctly in response to the brake pedal operation.
| NG |
|
|
|
7. |
READ VALUE USING GTS (SHIFT P SIGNAL) |
(a) Move the shift position to P.
(b) Read the Data List according to the display on the GTS.
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Shift P Signal |
Shift position P |
OFF or ON |
OFF: Shift position not in P ON: Shift position in P |
|
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Shift P Signal |
OK:
ON is displayed on the GTS.
| NG |
|
|
|
8. |
READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT P/N (STARTING CONTROL)) |
(a) Read the Data List according to the display on the GTS.
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Neutral Switch / Clutch Switch |
Shift position (P and N) |
OFF or ON |
OFF: Shift position in any position other than P or N ON: Shift position in P or N |
|
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Neutral Switch / Clutch Switch |
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Shift P/N (Starting Control) |
Park/Neutral position switch status |
OFF or ON |
OFF: Shift position in any position other than P or N ON: Shift position in P or N |
When OFF is displayed, the engine will not crank. |
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Shift P/N (Starting Control) |
OK:
The GTS display changes correctly in response to the shift position.
| NG |
|
|
|
9. |
READ VALUE USING GTS (POWER SUPPLY CONDITION) |
(a) Read the Data List according to the display on the GTS.
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Power Supply Condition |
Power supply state |
OFF, ACC ON, IGR ON, IGP ON or Starter ON |
OFF: Ignition switch off ACC ON: Ignition switch ACC IGR ON: Ignition switch ON IGP ON: Ignition switch ON Starter ON: Sending engine start request signal |
- |
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Power Supply Condition |
NOTICE:
Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.
OK:
The GTS display changes correctly in response to the engine switch operation.
| NG |
|
|
|
10. |
READ VALUE USING GTS (STARTER RELAY DRIVING REQUEST (STARTING CONTROL)) |
(a) Get into the vehicle while carrying an electrical key transmitter sub-assembly.
(b) Move the shift position to P.*1
(c) According to the display on the GTS, read the Data List while pressing the engine switch with the brake pedal depressed.*1
(d) According to the display on the GTS, read the Data List while pressing the engine switch with the clutch pedal depressed.*2
- *1: except Manual Transaxle
- *2: for Manual Transaxle
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Starter Relay Driving Request (Starting Control) |
Engine start request signal status |
OFF or ON |
except Manual Transaxle
for Manual Transaxle
|
|
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Starter Relay Driving Request (Starting Control) |
OK:
The GTS display changes.
| NG |
|
|
|
11. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY) |
|
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage: for M20A-FKS
for G16E-GTS
HINT: *: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V. |
|
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (except Manual Transaxle) |
B |
|
NG (for Manual Transaxle) |
C |
| B |
|
| C |
|
|
|
12. |
CHECK HARNESS AND CONNECTOR (ST RELAY - AUXILIARY BATTERY AND BODY GROUND) |
|
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance: for M20A-FKS:
for G16E-GTS:
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 5 - Body ground |
Always |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
13. |
INSPECT ST RELAY |
for M20A-FKS: Click here
for G16E-GTS: Click here
| NG |
|
REPLACE ST RELAY for M20A-FKS: Click here
for G16E-GTS: Click here
|
|
|
14. |
CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST RELAY) |
(a) Disconnect the C82 starter assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 3 - C82-1 (ST) |
Always |
Below 1 Ω |
|
No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 3 or C82-1 (ST) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
15. |
CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY) |
(a) Disconnect the C111 starter assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C111-1 (B) - Body ground |
Always |
11 to 14 V |
| OK |
|
REPLACE STARTER ASSEMBLY for M20A-FKS: Click here
for G16E-GTS: Click here
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
16. |
CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY) |
(a) Disconnect the C62 park/neutral position switch assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C62-5 (L) - No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 1 |
Always |
Below 1 Ω |
|
C62-5 (L) or No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 1 - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
17. |
CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ST RELAY) |
(a) Disconnect the A60 clutch switch assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A60-1 - No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 2 |
Always |
Below 1 Ω |
|
A60-1 or No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 2 - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
18. |
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
(a) Temporarily replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies.
Click here
|
|
19. |
CHECK WHETHER ENGINE STARTS |
(a) Check that the engine starts.
OK:
Engine starts normally.
| OK |
|
END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE) |
| NG |
|
|
20. |
READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW) |
(a) Disconnect the A47 ECM connector.
(b) Read the Data List according to the display on the GTS.
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Neutral Switch / Clutch Switch |
Shift position (P and N) |
OFF or ON |
OFF: Shift position in any position other than P or N ON: Shift position in P or N |
|
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Neutral Switch / Clutch Switch |
OK:
The GTS display changes correctly in response to the shift position.
| OK |
|
REPLACE ECM for M20A-FKS: Click here
for G16E-GTS: Click here
|
|
|
21. |
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Click here
| NG |
|
|
|
22. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY) |
(a) Disconnect the O175 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the C62 park/neutral position switch assembly connector.
(c) Disconnect the A47 ECM connector.
(d) Remove the ST relay.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O175-3 (STA) - C62-5 (L) |
Always |
Below 1 Ω |
|
O175-3 (STA) - A47-30 (STA) |
Always |
Below 1 Ω |
|
O175-3 (STA) - No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 1 |
Always |
Below 1 Ω |
|
O175-10 (STAR) - C62-4 (B) |
Always |
Below 1 Ω |
|
O175-10 (STAR) - A47-23 (NSW) |
Always |
Below 1 Ω |
|
O175-3 (STA), C62-5 (L) or A47-30 (STA) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
O175-3 (STA), C62-5 (L), A47-30 (STA) or No. 1 engine room relay block and No. 1 junction block assembly ST relay terminal 1 - Other terminals and body ground |
Always |
10 kΩ or higher |
|
O175-10 (STAR), C62-4 (B) or A47-23 (NSW) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
23. |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
(a) Connect the O175 certification ECU (smart key ECU assembly) connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O175-10 (STAR) - Body ground |
Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) |
6 V or higher* → 1.0 V or less |
HINT:
*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.
| NG |
|
|
|
24. |
INSPECT ST RELAY |
for M20A-FKS: Click here
for G16E-GTS: Click here
| OK |
|
| NG |
|
REPLACE ST RELAY for M20A-FKS: Click here
for G16E-GTS: Click here
|
|
25. |
CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY |
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I167-14 (P) - Body ground |
Shift position in P → Shift position not in P |
9 V or higher → 2.76 V or less |
| OK |
|
|
|
26. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY) |
(a) Disconnect the I167 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the I17 shift lock control unit assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I167-14 (P) - I17-3 (P2) |
Always |
Below 1 Ω |
|
I167-14 (P) or I17-3 (P2) - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
27. |
CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND GROUND) |
(a) Disconnect the A53 stop light switch assembly connector.
|
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A53-2 (GND) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
28. |
INSPECT STOP LIGHT SWITCH ASSEMBLY |
Click here
| NG |
|
|
|
29. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY) |
(a) Disconnect the O175 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the A47 ECM connector.
(c) Disconnect the A51 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the I17 shift lock control unit assembly connector.
(e) Disconnect the C80 TCM connector.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O175-21 (STP1) - A53-3 (L) |
Always |
Below 1 Ω |
|
O175-21 (STP1) or A53-3 (L) - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
30. |
READ VALUE USING GTS (NEUTRAL SWITCH / CLUTCH SWITCH) |
(a) Read the Data List according to the display on the GTS.
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Neutral Switch / Clutch Switch |
State of clutch pedal |
OFF or ON |
OFF: Clutch pedal released ON: Clutch pedal depressed |
|
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Neutral Switch / Clutch Switch |
OK:
The GTS display changes correctly in response to the clutch pedal operation.
| NG |
|
|
|
31. |
READ VALUE USING GTS (POWER SUPPLY CONDITION) |
(a) Read the Data List according to the display on the GTS.
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Power Supply Condition |
Power supply state |
OFF, ACC ON, IGR ON, IGP ON or Starter ON |
OFF: Ignition switch off ACC ON: Ignition switch ACC IGR ON: Ignition switch ON IGP ON: Ignition switch ON Starter ON: Sending engine start request signal |
- |
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Power Supply Condition |
NOTICE:
Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.
OK:
The GTS display changes correctly in response to the engine switch operation.
| OK |
|
|
|
32. |
CHECK STEERING LOCK FUNCTION |
(a) Check that the steering unlocks when the ignition switch is turned to ACC.
OK:
The steering unlocks.
| OK |
|
| NG |
|
GO TO OTHER PROBLEM (Unable to Unlock Steering Wheel (Engine cannot Start)) |
|
33. |
INSPECT CLUTCH SWITCH ASSEMBLY |
Click here
| NG |
|
|
|
34. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH SWITCH ASSEMBLY) |
(a) Disconnect the O175 certification ECU (smart key ECU assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O175-10 (STAR) - A60-2 |
Always |
Below 1 Ω |
|
O175-10 (STAR) or A60-2 - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|