Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000026BOZ
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): B132187; Lost Communication with EMV Missing Message; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

DTC

B132187

Lost Communication with EMV Missing Message

DESCRIPTION

After the combination meter assembly has started, the combination meter assembly attempts to detect the radio and display receiver assembly by performing communication via local bus.

This DTC is stored when the radio and display receiver assembly has been detected but communication between the combination meter assembly and radio and display receiver assembly is interrupted.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B132187

Lost Communication with EMV Missing Message

Diagnosis Condition:

  • The combination meter assembly has started
  • The radio and display receiver assembly has started

Malfunction Status:

  • After the radio and display receiver assembly is detected, communication via local bus is interrupted

Malfunction Time:

  • 30 seconds or more
  • Harness or connector
  • Radio and display receiver assembly
  • Combination meter assembly

Combination Meter

A

WIRING DIAGRAM

for TMC Made
for TMMMS Made

CHECK POINT

  • When DTC B132187 is output from the combination meter assembly, other ECUs on the same detection circuit may simultaneously output the same DTC depending on the malfunctioning area.
  • Depending on the combination of DTCs simultaneously output by each ECU, the malfunctioning area can be narrowed down. Refer to the following table for DTC combinations output by each ECU.

for TMC Made

DTC Output Pattern

DTC Output Part Name

(Display on GTS)

Malfunction Status/Suspected Area

Combination Meter Assembly

(Combination Meter)

Radio and Display Receiver Assembly

(Navigation System)

1

B132187

U11D087

  • Radio and display receiver assembly
  • Harness or connector
  • Combination meter assembly

2

B132187

Not output

  • Radio and display receiver assembly
  • Combination meter assembly

for TMMMS Made

DTC Output Pattern

DTC Output Part Name

(Display on GTS)

Malfunction Status/Suspected Area

Combination Meter Assembly

(Combination Meter)

Radio and Display Receiver Assembly

(Navigation System)

1

B132187

B1324

  • Radio and display receiver assembly
  • Harness or connector
  • Combination meter assembly

2

B132187

Not output

  • Radio and display receiver assembly
  • Combination meter assembly

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
  • for TMC Made

    When replacing the combination meter assembly, update the ECU security key.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: UPDATE ECU SECURITY KEY

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

  • If the power source circuit for any of the following ECUs is malfunctioning, DTCs may not be correctly output. Therefore, before performing troubleshooting using the following procedure, perform inspections related to the power source circuit of each ECU.
    • Radio and display receiver assembly

      Audio and Visual System (for Gasoline Model with Dual Knob Type): Click here 2019 - 2023 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 11/2022]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (for Gasoline Model with Dual Knob Type): HOW TO PROCEED WITH TROUBLESHOOTING

      Audio and Visual System (for Single Knob Type): Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (for Single Knob Type): HOW TO PROCEED WITH TROUBLESHOOTING

      Navigation System: Click here 2019 - 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 11/2022]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

    • Combination meter assembly

      Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): Power Source Circuit

PROCEDURE

1.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for TMC Made

A

for TMMMS Made

B

B

GO TO STEP 6

A

2.

CHECK FOR DTC

(a) Check each system for DTCs.

Body Electrical > Combination Meter > Trouble Codes

Body Electrical > Navigation System > Trouble Codes

(b) Confirm the DTC combinations of the following table.

DTC Output Pattern

DTC Output Part Name

(Display on GTS)

Combination Meter Assembly

(Combination Meter)

Radio and Display Receiver Assembly

(Navigation System)

1

B132187

U11D087

2

B132187

Not output

Result

Proceed to

DTC output pattern 1

A

DTC output pattern 2

B

B

GO TO STEP 4

A

3.

INSPECT EACH ECU (INTERNAL MALFUNCTION)

(a) Remove 1 of the following ECUs.

  • Radio and display receiver assembly

    HINT:

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

  • Combination meter assembly

    HINT:

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL

(b) Measure the resistance of the removed ECU.

NOTICE:

  • Refer to the following table for the specified conditions of each ECU.
  • If the specified conditions are met, repeat the inspection procedure from step (a) for another ECU.

HINT:

If the results of an ECU are not as specified, it is suspected that the ECU is the cause of the DTC.

(1) Inspect the radio and display receiver assembly.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I175-11 (CNH1) - I175-12 (CNL1)

Always

108 to 132 Ω

*a

Component without harness connected

(Radio and Display Receiver Assembly)

(2) Inspect the combination meter assembly.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I5-32 (TX+) - I5-15 (TX-)

Always

108 to 132 Ω

Result:

Result

Proceed to

The results of all ECUs are as specified

A

The results of the radio and display receiver assembly is not as specified

B

The results of the combination meter assembly is not as specified

C

*a

Component without harness connected

(Combination Meter Assembly)

A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

REPLACE COMBINATION METER ASSEMBLY

4.

CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Combination Meter > Clear DTCs

NEXT

5.

CHECK FOR DTC

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

HINT:

By disconnecting the cable from the negative (-) auxiliary battery terminal, the internally stored information related to local bus communication for the combination meter assembly is reset.

(b) Disconnect the I175 radio and display receiver assembly connector.

(c) Connect the cable to the negative (-) auxiliary battery terminal.

(d) Turn the ignition switch to ON.

(e) Wait 30 seconds or more.

(f) Check for DTCs.

Body Electrical > Combination Meter > Trouble Codes

HINT:

By resetting the internally stored information related to local bus communication, the detection conditions of DTC B132187 are not met as the combination meter assembly does not detect the radio and display receiver assembly. If the combination meter assembly is operating normally, DTC B132187 will not be stored.

Result

Proceed to

DTC B132187 is not output

A

DTC B132187 is output

B

A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

REPLACE COMBINATION METER ASSEMBLY

6.

CHECK FOR DTC

(a) Check each system for DTCs.

Body Electrical > Combination Meter > Trouble Codes

Body Electrical > Navigation System > Trouble Codes

(b) Confirm the DTC combinations of the following table.

DTC Output Pattern

DTC Output Part Name

(Display on GTS)

Combination Meter Assembly

(Combination Meter)

Radio and Display Receiver Assembly

(Navigation System)

1

B132187

B1324

2

B132187

Not output

Result

Proceed to

DTC output pattern 1

A

DTC output pattern 2

B

B

GO TO STEP 8

A

7.

INSPECT EACH ECU (INTERNAL MALFUNCTION)

(a) Remove 1 of the following ECUs.

  • Radio and display receiver assembly

    HINT:

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; AUDIO / VIDEO: RADIO RECEIVER: REMOVAL

  • Combination meter assembly

    HINT:

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; METER / GAUGE / DISPLAY: COMBINATION METER: REMOVAL

(b) Measure the resistance of the removed ECU.

NOTICE:

  • Refer to the following table for the specified conditions of each ECU.
  • If the specified conditions are met, repeat the inspection procedure from step (a) for another ECU.

HINT:

If the results of an ECU are not as specified, it is suspected that the ECU is the cause of the DTC.

(1) Inspect the radio and display receiver assembly.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I56-5 (CNH1) - I56-6 (CNL1)

Always

108 to 132 Ω

*a

Component without harness connected

(Radio and Display Receiver Assembly)

(2) Inspect the combination meter assembly.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I4-27 (MSCH) - I4-10 (MSCL)

Always

108 to 132 Ω

Result:

Result

Proceed to

The results of all ECUs are as specified

A

The results of the radio and display receiver assembly is not as specified

B

The results of the combination meter assembly is not as specified

C

*a

Component without harness connected

(Combination Meter Assembly)

A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

REPLACE COMBINATION METER ASSEMBLY

8.

CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Combination Meter > Clear DTCs

NEXT

9.

CHECK FOR DTC

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

HINT:

By disconnecting the cable from the negative (-) auxiliary battery terminal, the internally stored information related to local bus communication for the combination meter assembly is reset.

(b) Disconnect the I56 radio and display receiver assembly connector.

(c) Connect the cable to the negative (-) auxiliary battery terminal.

(d) Turn the ignition switch to ON.

(e) Wait 30 seconds or more.

(f) Check for DTCs.

Body Electrical > Combination Meter > Trouble Codes

HINT:

By resetting the internally stored information related to local bus communication, the detection conditions of DTC B132187 are not met as the combination meter assembly does not detect the radio and display receiver assembly. If the combination meter assembly is operating normally, DTC B132187 will not be stored.

Result

Proceed to

DTC B132187 is not output

A

DTC B132187 is output

B

A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

REPLACE COMBINATION METER ASSEMBLY