Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM1000000026A79
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): Steering Lock does not Lock; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]

Steering Lock does not Lock

DESCRIPTION

The steering lock actuator or upper bracket assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.

Related Data List and Active Test Items

Problem Symptom

Data List and Active Test

Steering Lock does not Lock

Smart Key

  • Lock Request Receive
  • L Code Check
  • S Code Check
  • Steering Lock

Main Body

  • FL Door Courtesy SW

Power Source Control

  • Shift P Signal

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus Body Electrical Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
  • Perform either of the following operations to lock/unlock the steering:

    for Manual Transaxle

    • To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).
    • To lock the steering, turn the engine switch off, and then open a door.

    except Manual Transaxle

    • To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).
    • To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.
  • The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.

    Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): HOW TO PROCEED WITH TROUBLESHOOTING

  • Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), refer to Registration.

    Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): REGISTRATION

  • After performing repairs, confirm that the problem does not recur.
  • When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

PROCEDURE

1.

READ VALUE USING TECHSTREAM (LOCK REQUEST RECEIVE)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Lock Request Receive

Status of steering lock command from certification ECU (smart key ECU assembly)

OK or NG

for Manual Transaxle

  • OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with engine switch off)
  • NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with engine switch off)

except Manual Transaxle

  • OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and engine switch off)
  • NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and engine switch off)

If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

Body Electrical > Smart Key > Data List

Tester Display

Lock Request Receive

OK:

for Manual Transaxle

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to on (ACC) or off and opening a door, and OK is displayed on the Techstream screen.

except Manual Transaxle

The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the engine switch from on (IG) to on (ACC) or off and opening a door with the shift lever in P, and OK is displayed on the Techstream screen.

NG

GO TO STEP 12

OK

2.

READ VALUE USING TECHSTREAM (S CODE CHECK)

(a) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

S Code Check

S code verification result

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When NG is displayed:

  • The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot be started).

Body Electrical > Smart Key > Data List

Tester Display

S Code Check

OK:

OK is displayed on the Techstream.

HINT:

Reasons for verification failure:

  • The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
  • There is a problem with the communication between ECUs.
  • An ECU was replaced, but not registered.
  • An ECU was replaced with an ECU which has already been registered to another vehicle.
NG

GO TO STEP 11

OK

3.

READ VALUE USING TECHSTREAM (L CODE CHECK)

(a) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

L Code Check

Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When NG is displayed:

  • The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot be started).

Body Electrical > Smart Key > Data List

Tester Display

L Code Check

OK:

OK is displayed on the Techstream.

HINT:

Reasons for verification failure:

  • The steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly) is malfunctioning.
  • There is a problem with the communication between ECUs.
  • An ECU was replaced, but not registered.
  • An ECU was replaced with an ECU which has already been registered to another vehicle.
NG

GO TO STEP 10

OK

4.

CHECK FOR DTC

(a) Check for DTCs.

Chassis > ABS/VSC/TRC > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

w/ Electric Parking Brake System: Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System TMMMS Made): DIAGNOSTIC TROUBLE CODE CHART

w/o Electric Parking Brake System: Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMMMS Made): DIAGNOSTIC TROUBLE CODE CHART

A

5.

READ VALUE USING TECHSTREAM (STEERING LOCK)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Smart Key / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Sensor Value

History of malfunction of position sensor in steering lock ECU (steering lock actuator or upper bracket assembly) (DTC B2781 is stored)

OK or NG(Past)

OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) does not exist.

NG(Past): History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator or upper bracket assembly) being on exists. (Under normal operation, neither sensor is on.)

When NG(Past) is displayed, either the position sensor in the steering lock ECU (steering lock actuator or upper bracket assembly) or the assembly itself may be malfunctioning.

Body Electrical > Smart Key > Data List

Tester Display

Sensor Value

OK:

OK is displayed on the Techstream.

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

OK

6.

CHECK HARNESS AND CONNECTOR (POWER SOURCE)

(a) Disconnect the I59 steering lock ECU (steering lock actuator or upper bracket assembly) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I59-1 (GND) - Body ground

Always

Below 1 Ω

NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.

*a

Front view of wire harness connector

(to Steering Lock ECU Steering Lock Actuator or Upper Bracket Assembly))

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

I59-7 (B) - Body ground

Always

11 to 14 V
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

7.

CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

(a) Connect the I59 steering lock ECU (steering lock actuator or upper bracket assembly) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

I59-3 (IGE) - I59-1 (GND)

for Manual Transaxle

  • Steering lock motor operating when all conditions met, and then door opened:
    • The steering is unlocked.
    • The engine switch is off.

except Manual Transaxle

  • Steering lock motor operating when all conditions met, and then door opened:
    • The steering is unlocked.
    • The engine switch is off.
    • The shift lever is in P.

11 to 14 V → Below 1 V

*a

Component with harness connected

(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

8.

CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

(a) Disconnect the I59 steering lock ECU (steering lock actuator or upper bracket assembly) connector.

(b) Disconnect the I1 certification ECU (smart key ECU assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I59-3 (IGE) - I1-25 (SLR+)

Always

Below 1 Ω

I59-3 (IGE) or I1-25 (SLR+) - Other terminals and body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

9.

CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

(a) Connect the I59 steering lock ECU (steering lock actuator or upper bracket assembly) connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

I59-3 (IGE) - Body ground

Always

11 to 14 V

*a

Component with harness connected

(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

10.

CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

(a) Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one and perform registration.

HINT:

  • For replacement.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: DISASSEMBLY

  • For registration.

    Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): REGISTRATION

(b) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

L Code Check

Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When NG is displayed:

  • The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot be started).

Body Electrical > Smart Key > Data List

Tester Display

L Code Check

OK:

OK is displayed on the Techstream.

OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)
NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

11.

CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

  • For replacement.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

  • For registration.

    Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): REGISTRATION

(b) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

S Code Check

S code verification result

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When NG is displayed:

  • The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot be started).

Body Electrical > Smart Key > Data List

Tester Display

S Code Check

OK:

OK is displayed on the Techstream.

OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)
NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

12.

READ VALUE USING TECHSTREAM (FL DOOR COURTESY SW)

(a) Enter the following menus: Body Electrical / Main Body / Data List.

(b) Using the Techstream, check the following main body ECU (multiplex network body ECU) Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

FL Door Courtesy SW

Front door LH courtesy light switch signal

OFF or ON

OFF: Front door LH closed

ON: Front door LH open

-

Body Electrical > Main Body > Data List

Tester Display

FL Door Courtesy SW

OK:

The Data List item changes in accordance with the opening and closing of the driver door.

Result

Proceed to

OK (except Manual Transaxle)

A

OK (for Manual Transaxle)

B

NG

C
B

GO TO STEP 15

C

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit)

A

13.

READ VALUE USING TECHSTREAM (SHIFT P SIGNAL)

(a) Enter the following menus: Body Electrical / Power Source Control / Data List.

(b) Move the shift lever to P.

(c) Read the Data List according to the display on the Techstream.

Body Electrical > Power Source Control > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Shift P Signal

Shift position P

OFF or ON

OFF: Shift lever not in P

ON: Shift lever in P

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

Body Electrical > Power Source Control > Data List

Tester Display

Shift P Signal

OK:

ON is displayed on the Techstream.

NG

GO TO OTHER PROBLEM

OK

14.

CHECK FOR DTC

(a) Check for DTCs.

Chassis > ABS/VSC/TRC > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

w/ Electric Parking Brake System: Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System TMMMS Made): DIAGNOSTIC TROUBLE CODE CHART

w/o Electric Parking Brake System: Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMMMS Made): DIAGNOSTIC TROUBLE CODE CHART

A

15.

READ VALUE USING TECHSTREAM (STEERING LOCK)

(a) Enter the following menus: Body Electrical / Smart Key / Data List.

(b) Check that the steering is unlocked.

(c) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Steering Lock

Steering lock ECU (steering lock actuator or upper bracket assembly) lock confirmation status

Unset or Set

Unset: Lock not confirmed

Set: Lock confirmed

When Unset is displayed, the steering is not locked.

Body Electrical > Smart Key > Data List

Tester Display

Steering Lock

OK:

Set is displayed on the Techstream.

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

OK

16.

READ VALUE USING TECHSTREAM (LOCK REQUEST RECEIVE)

(a) Replace the certification ECU (smart key ECU assembly) with a new one and perform registration.

HINT:

  • For replacement.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL

  • For registration.

    Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): REGISTRATION

(b) Read the Data List according to the display on the Techstream.

Body Electrical > Smart Key > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Lock Request Receive

Status of steering unlock command from certification ECU (smart key ECU assembly)

OK or NG

for Manual Transaxle

  • OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with engine switch off)
  • NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with engine switch off)

except Manual Transaxle

  • OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and engine switch off)
  • NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and engine switch off)

If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.

Body Electrical > Smart Key > Data List

Tester Display

Lock Request Receive

OK:

for Manual Transaxle

Within 10 seconds after any of the doors is opened with engine switch off, the Data List item changes to "OK".

except Manual Transaxle

Within 10 seconds after any of the doors is opened with shift lever in P and engine switch off, the Data List item changes to "OK".

OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)
NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)