Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026A1M |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function (TMMMS Made)): B27A1; Open in Driver Side Electrical Antenna Circuit; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] |
DTC
|
B27A1
|
Open in Driver Side Electrical Antenna Circuit
|
DESCRIPTION
The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for driver door) (electrical key antenna) at intervals of 0.25 seconds. For the front door outside handle assembly (for driver door) (electrical key antenna) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, a signal requesting a response from the electrical key transmitter sub-assembly is transmitted within approximately 1 m (3.28 ft.) of the driver door at intervals of 0.25 seconds. DTC B27A1 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (electrical key antenna) (between terminals CLG1 and ANT1, or terminals CG1B and ANT2).
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Note
|
B27A1
|
Open in Driver Side Electrical Antenna Circuit
|
An open is detected in the circuit between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) (CLG1 - ANT1, CG1B - ANT2) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*).
|
-
Certification ECU (smart key ECU assembly)
-
Front door outside handle assembly (for driver door)
-
Harness or connector
|
DTC Output Confirmation Operation:
|
-
*: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected
|
Fail-safe Operation when Malfunction Detected
|
Entry lock/unlock operation cannot be performed for driver door
|
-
|
Related Data List and Active Test
DTC No.
|
Data List and Active Test
|
B27A1
|
Key diagnostic mode can be used to perform troubleshooting
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
-
The smart key system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
Click here
-
Before replacing the certification ECU (smart key ECU assembly), refer to Precaution.
Click here
-
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
1.
|
CHECK CONNECTOR CONNECTION
|
(a) Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door).
OK:
Connectors are properly connected.
NG |
|
CONNECT CONNECTORS PROPERLY
|
OK
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
|
(a) Disconnect the O61 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the L3 front door outside handle assembly (for driver door) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
O61-17 (CLG1) - L3-6 (ANT1)
|
Always
|
Below 1 Ω
|
O61-16 (CG1B) - L3-4 (ANT2)
|
Always
|
Below 1 Ω
|
(d) Reconnect the O61 certification ECU (smart key ECU assembly) connector.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR))
|
*a
|
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
|
*b
|
Waveform 1
|
*c
|
Waveform 2
|
*d
|
Waveform 3
|
*e
|
Waveform 4
|
-
|
-
|
(a) Using an oscilloscope, check the waveform.
OK:
Tester Connection
|
Condition
|
Tool Setting
|
Specified Condition
|
O61-17 (CLG1) - I1-18 (E)
|
Procedure:
-
Ignition switch off
-
All doors closed
-
Electrical key transmitter sub-assembly not inside vehicle
-
All doors locked through wireless operation
(electrical key transmitter sub-assembly brought inside detection area*)
|
5 V/DIV., 500 ms/DIV.
|
Pulse generation
(See waveform 1)
|
Procedure:
-
Ignition switch off
-
All doors closed
-
Electrical key transmitter sub-assembly not inside vehicle
-
All doors locked through wireless operation
(electrical key transmitter sub-assembly brought outside detection area*)
|
5 V/DIV., 100 ms/DIV.
|
Pulse generation
(See waveform 2)
|
O61-16 (CG1B) - I1-18 (E)
|
Procedure:
-
Ignition switch off
-
All doors closed
-
Electrical key transmitter sub-assembly not inside vehicle
-
All doors locked through wireless operation
(electrical key transmitter sub-assembly brought inside detection area*)
|
5 V/DIV., 500 ms/DIV.
|
Pulse generation
(See waveform 3)
|
Procedure:
-
Ignition switch off
-
All doors closed
-
Electrical key transmitter sub-assembly not inside vehicle
-
All doors locked through wireless operation
(electrical key transmitter sub-assembly brought outside detection area*)
|
5 V/DIV., 100 ms/DIV.
|
Pulse generation
(See waveform 4)
|
-
*: For details about the entry function detection area, refer to Operation Check.
Click here
|