| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000269FV |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - ] |
| Title: DOOR LOCK: KEY REMINDER WARNING SYSTEM: DATA LIST / ACTIVE TEST; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ] | ||
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the GTS to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the GTS on.
(d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List according to the display on the GTS. (for TMMMS Made)
Body Electrical > Main Body > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Key Unlock Warning SW |
Unlock warning switch signal |
OFF or ON |
OFF: No key in ignition key cylinder ON: Key in ignition key cylinder |
- |
|
FL Door Courtesy SW |
Front door courtesy light switch assembly (for LH) signal |
OFF or ON |
OFF: Front door LH closed ON: Front door LH open |
- |
(f) Read the Data List according to the display on the GTS. (for TMC Made)
Body Electrical > Main Body > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
FL Door Courtesy Switch Status |
Front door courtesy light switch assembly (for LH) signal |
Close or Open |
Close: Front door LH closed Open: Front door LH open |
- |
|
Key Unlock Warning Switch |
Unlock warning switch signal |
OFF or ON |
OFF: No key in ignition key cylinder ON: Key in ignition key cylinder |
- |
ACTIVE TEST
HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the GTS to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the GTS on.
(d) Enter the following menus: Body Electrical / Combination Meter/ Active Test.
(e) Perform the Active Test according to the display on the GTS.
Body Electrical > Combination Meter > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Buzzer Operation (800Hz, Vol L, W/ Damping) |
Combination meter buzzer
|
ON |
- |
|
Buzzer Operation (800Hz, Vol L, W/O Damping) |
Combination meter buzzer
|
ON |
- |
|
Buzzer Operation (800Hz, Vol S, W/ Damping) |
Combination meter buzzer
|
ON |
- |
|
Buzzer Operation (800Hz, Vol S, W/O Damping) |
Combination meter buzzer
|
ON |
- |
|
Buzzer Operation (1.6kHz, Vol S, W/O Damping) |
Combination meter buzzer
|
ON |
- |
|
Buzzer Operation (2.0kHz, Vol S, W/O Damping) |
Combination meter buzzer
|
ON |
- |
|
Buzzer Operation (2.4kHz, Vol L, W/O Damping) |
Combination meter buzzer
|
ON |
- |
|
|