Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000002692X
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 -           ]
Title: AXLE AND DIFFERENTIAL: REAR AXLE HUB BOLT (for Torsion Beam Type Suspension): REPLACEMENT; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]

REPLACEMENT

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE REAR WHEEL

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL

2. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(a) Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:

  • Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
  • Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.

3. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

(a) Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear caliper support bracket.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.

4. REMOVE REAR DISC

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; BRAKE (REAR): REAR BRAKE (w/ Electric Parking Brake): REMOVAL+

5. REMOVE REAR AXLE HUB BOLT

(a) Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)

NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.

*a

Service Nut

(b) Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST: 09611-12010

NOTICE:

Do not damage the threads of the rear axle hub bolts.

6. INSTALL REAR AXLE HUB BOLT

(a) Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.

*a

Service Nut

*b

Washer

(b) Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)

HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.

(c) Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:

  • Install the service nuts to prevent damage to the rear axle hub bolts.
  • Do not damage the threads of the rear axle hub bolts.

(d) Remove the 3 service nuts and washer from the 3 rear axle hub bolts.

7. INSTALL REAR DISC

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; BRAKE (REAR): REAR BRAKE (w/ Electric Parking Brake): INSTALLATION+

8. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

(a) Install the rear disc brake caliper assembly to the rear caliper support bracket with the 2 bolts.

Torque:

107 N·m {1091 kgf·cm, 79 ft·lbf}

9. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(a) Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.

NOTICE:

  • Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
  • Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.

10. INSTALL REAR WHEEL

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; MAINTENANCE: TIRE AND WHEEL: INSTALLATION