Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000268J1
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 -           ]
Title: G16E-GTS (INTAKE / EXHAUST): INTAKE SYSTEM: ON-VEHICLE INSPECTION; 2023 - 2025 MY GR Corolla [09/2022 -        ]

ON-VEHICLE INSPECTION

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced when repairing air leaks in the intake system are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Air leaks from intake system

Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.

2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

PROCEDURE

1. INSPECT INTAKE SYSTEM

CAUTION:

To prevent injury due to contact with an operating cooling fan, keep your hands and clothing away from the cooling fans when working in the engine compartment with the engine running or the engine switch on (IG).

HINT:

Perform "Inspection After Repair" after repairing vacuum leaks in the intake system.

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

(a) Check that there are no vacuum leaks at the points shown in the illustration.

2. PERFORM INITIALIZATION

(a) Perform "Inspection After Repair" after repairing vacuum leaks in the intake system.

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

3. INSPECT INTAKE AIR CONTROL VALVE ACTUATOR

(a) Disconnect the vacuum hose from the intake air control valve actuator.

(b) Confirm that the intake air control valve opens smoothly under vacuum and closes smoothly when the vacuum is released.

If the intake air control valve does not close or open smoothly, replace the air cleaner assembly.

*a

Vacuum released

*b

Vacuum applied

*c

Intake Air Control Valve Actuator

*d

Intake Air Control Valve

(c) Connect the vacuum hose to the intake air control valve actuator.

4. INSPECT VACUUM SWITCHING VALVE ASSEMBLY (for AICV)

(a) Disconnect the vacuum switching valve assembly (for AICV) connector.

(b) Disconnect the 2 vacuum hoses from the vacuum switching valve assembly (for AICV).

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

20°C (68°F)

37 to 44 Ω

C137-1 - Body ground

Always

10 kΩ or higher

C137-2 - Body ground

Always

10 kΩ or higher

If the result is not as specified, replace the air cleaner assembly.

*a

Component without harness connected

(Vacuum Switching Valve Assembly (for AICV))

*b

Body Ground

(d) Check the operation of the vacuum switching valve assembly (for AICV).

(1) When vacuum is applied to the port (E), check that air is sucked into the filter.

If air is not sucked into the filter, replace the air cleaner assembly.

*a

Filter

*b

Port (E)

*c

Air

(2) Apply battery voltage across the terminals. When vacuum is applied to the port (F), check that air is sucked into the port (E).

If air is not sucked into the port (F), replace the air cleaner assembly.

*a

Port (E)

*b

Port (F)

*c

Air