2ZR-FXE (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION; 2023 - 2025 MY Corolla Corolla HV [09/2022

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM10000000267J8
Model Year Start: 2023	Model: Corolla	Prod Date Range: [09/2022 - ]
Title: 2ZR-FXE (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION; 2023 - 2025 MY Corolla Corolla HV [09/2022 - ]

INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click here

PROCEDURE

1. INSTALL ENGINE HANGERS

Click here

2. REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

(a) Remove the engine assembly from the engine stand.

3. INSTALL FLYWHEEL SUB-ASSEMBLY

Click here

4. INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

Click here

5. INSTALL ENGINE ASSEMBLY

Click here

6. INSTALL ENGINE WIRE

(a) Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.

7. INSTALL FLYWHEEL HOUSING SIDE COVER

Click here

8. INSTALL STARTER HOLE INSULATOR

Click here

9. INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

Click here

10. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.

(a) Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.

*a	Temporarily Tighten

(b) Install the 2 bolts and nut in the order shown in the illustration.

Torque:

72 N·m {734 kgf·cm, 53 ft·lbf}

(c) Connect the air conditioner tube and accessory assembly to the engine mounting insulator sub-assembly RH with the bolt and nut.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

(d) Install the No. 2 earth wire to the engine mounting insulator sub-assembly RH and vehicle body with the 2 bolts as shown in the illustration.

Torque:

10.5 N·m {107 kgf·cm, 8 ft·lbf}

NOTICE:

Make sure that the mark is facing the front of the vehicle.

*a	Mark
*b	Contact Point to Stop Rotation When Tightening
*c	Front of Vehicle
*d	LH Side

11. INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.

(a) Temporarily install the engine mounting insulator LH to the vehicle.

*a	Temporarily Tighten

(b) Install the 4 bolts and nut in the order shown in the illustration.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

12. REMOVE ENGINE HANGER

Click here

13. INSTALL WIRE HARNESS CLAMP BRACKET

(a) Install the wire harness clamp bracket with the bolt.

Torque:

39 N·m {398 kgf·cm, 29 ft·lbf}

(b) Engage the 3 clamps.

14. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

(a) Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.

(b) Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.

NOTICE:

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.

Torque:

141 N·m {1438 kgf·cm, 104 ft·lbf}

(d) Apply adhesive to 2 or 3 threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

Adhesive

(e) Install the No. 2 engine mounting stay LH with the bolt.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(f) Install the engine mounting insulator LH to the hybrid vehicle transaxle assembly with the 3 bolts and nut.

Torque:

Bolt :

70 N·m {714 kgf·cm, 52 ft·lbf}

Nut :

20 N·m {204 kgf·cm, 15 ft·lbf}

(g) Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.

Torque:

Bolt :

72 N·m {734 kgf·cm, 53 ft·lbf}

Nut :

41 N·m {418 kgf·cm, 30 ft·lbf}

15. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Click here

16. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

17. INSTALL FRONT DRIVE SHAFT ASSEMBLY

Click here

18. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Click here

19. INSTALL FRONT FLOOR CENTER BRACE

Click here

20. INSTALL FRONT FLOOR COVER LH

Click here

21. INSTALL FRONT FLOOR COVER RH

HINT:

Use the same procedure as for the LH side.

22. CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Click here

23. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Click here

24. INSTALL COLUMN HOLE COVER SILENCER SHEET

Click here

25. CONNECT NO. 7 ENGINE WIRE

(a) Connect the No. 7 engine wire to the hybrid vehicle transaxle assembly with the bolt.

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

(b) Engage the 2 clamps.

26. CONNECT SUCTION HOSE SUB-ASSEMBLY

Click here

27. CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Click here

28. CONNECT NO. 2 INVERTER COOLING OUTLET HOSE

(a) Connect the No. 2 inverter cooling outlet hose to the motor cooling cooler and slide the clip to secure it.

29. CONNECT FUEL TUBE SUB-ASSEMBLY

Click here

30. CONNECT FUEL VAPOR FEED HOSE

(a) Connect the fuel vapor feed hose to the fuel vapor feed pipe and slide the clip to secure it.

31. CONNECT OUTLET HEATER WATER HOSE

(a) Connect the outlet heater water hose.

32. CONNECT INLET HEATER WATER HOSE

(a) Connect the inlet heater water hose.

33. CONNECT NO. 2 RADIATOR HOSE

(a) Connect the No. 2 radiator hose to the water inlet sub-assembly and slide the clip to secure it.

34. CONNECT NO. 1 RADIATOR HOSE (for Type B)

(a) Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.

35. CONNECT NO. 3 RADIATOR HOSE (for Type A)

(a) Connect the No. 3 radiator hose to the water outlet and slide the clip to secure it.

36. CONNECT FLOOR SHIFT TRANSMISSION CONTROL SELECT CABLE

(a) Connect the floor shift transmission control select cable to the engine assembly with the bolt.

Torque:

12 N·m {122 kgf·cm, 9 ft·lbf}

(b) Connect the floor shift transmission control select cable to the transmission control cable support.

(c) Connect the floor shift transmission control select cable to the No. 1 transmission control cable bracket with a new clip.

(d) Connect the floor shift transmission control select cable to the transmission control shaft lever as shown in the illustration.

*a	Correct
*b	Incorrect

37. INSTALL INVERTER WITH CONVERTER ASSEMBLY

Click here

38. INSTALL INLET NO. 1 AIR CLEANER

Click here

39. INSTALL AIR CLEANER SUPPORT BRACKET ASSEMBLY

Click here

40. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Click here

41. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here

42. INSTALL THROTTLE BODY ASSEMBLY

Click here

43. INSTALL INLET NO. 2 AIR CLEANER

Click here

44. INSTALL RADIATOR SUPPORT OPENING COVER

Click here

45. CONNECT NO. 8 WATER BY-PASS HOSE

(a) Connect the No. 8 water by-pass hose to the No. 4 water by-pass hose and slide the clip to secure it.

46. ADD ENGINE OIL

Click here

47. ADD HYBRID TRANSAXLE FLUID

Click here

48. ADD ENGINE COOLANT (for Engine)

Click here

49. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

for HFO-1234yf(R1234yf):
Click here
for HFC-134a(R134a):
Click here

50. CHECK ENGINE OIL LEVEL

Click here

51. INSPECT HYBRID TRANSAXLE FLUID

Click here

52. INSPECT SHIFT LEVER POSITION

Click here

53. ADJUST SHIFT LEVER POSITION

Click here

54. INSPECT FOR COOLANT LEAK (for Inverter)

Click here

55. INSPECT FOR COOLANT LEAK (for Engine)

Click here

56. WARM UP COMPRESSOR

for HFO-1234yf(R1234yf):
Click here
for HFC-134a(R134a):
Click here

57. INSPECT FOR REFRIGERANT LEAK

for HFO-1234yf(R1234yf):
Click here
for HFC-134a(R134a):
Click here

58. INSPECT FOR FUEL LEAK

Click here

59. INSPECT FOR OIL LEAK

Click here

60. INSPECT FOR EXHAUST GAS LEAK

Click here

61. INSTALL REAR ENGINE UNDER COVER LH

(a) Type A:

(1) Install the rear engine under cover LH to the vehicle with the 4 clips.

(2) Install the screw.

(b) Type B:

(1) Install the rear engine under cover LH to the vehicle with the 5 clips.

(2) Install the screw.

62. INSTALL REAR ENGINE UNDER COVER RH

(a) Type A:

(1) Install the rear engine under cover RH to the vehicle with the 4 clips.

(2) Install the screw.

(b) Type B:

(1) Install the rear engine under cover RH to the vehicle with the 5 clips.

(2) Install the screw.

63. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

(a) Install the No. 1 engine under cover assembly to the vehicle with the 10 clips.

(b) Install the 4 bolts.

Torque:

7.5 N·m {76 kgf·cm, 66 in·lbf}

64. INSTALL FRONT WHEELS

Click here

65. INSPECT IGNITION TIMING

Click here

66. INSPECT ENGINE IDLE SPEED

Click here

67. INSPECT CO/HC

Click here

68. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Click here

69. CHECK SPEED SENSOR SIGNAL

Click here

70. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here