SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): INSTALLATION; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000026782
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [09/2022 - 11/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): INSTALLATION; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

INSTALLATION

PROCEDURE

1. INSTALL SIDE AIRBAG PRESSURE SENSOR

(a) Check that the ignition switch (for Gasoline Model) or power switch (for HV Model) is off.

(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

for TMC Made:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

for TMMMS Made:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

(1) Insert the side airbag pressure sensor stopper into the door hole, engage the claw and install the side airbag pressure sensor to the front door panel with the nut.

Torque:

for G16E-GTS :

7.8 N·m {80 kgf·cm, 69 in·lbf}

except G16E-GTS :

9.0 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

If the side airbag pressure sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the side airbag pressure sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
Make sure that the side airbag pressure sensor stopper is securely inserted into the door hole.
Keep the stud bolt and waterproof rubber seal free of foreign matter.

Stopper

(d) for TMMMS Made:

(1) Engage the 2 stoppers to temporarily install the side airbag pressure sensor to the front door panel.

Stopper

(2) Install the side airbag pressure sensor with the nut.

Torque:

9.0 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

If the side airbag pressure sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the side airbag pressure sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
Make sure that the side airbag pressure sensor stopper is securely inserted into the door hole.
Keep the stud bolt and waterproof rubber seal free of foreign matter.

(e) Connect the connector to the side airbag pressure sensor.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click here

(f) Check that there is no looseness in the installed parts of the side airbag pressure sensor.

2. INSTALL FRONT DOOR SERVICE HOLE COVER

Click here

3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

4. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

5. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

6. INSTALL FRONT DOOR ASSIST GRIP ASSEMBLY

Click here

7. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

Click here

8. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

for M20A-FKS: Click here

for 2ZR-FAE: Click here

for 2ZR-FXE: Click here

for G16E-GTS: Click here

9. INSTALL DECK BOARD ASSEMBLY (for G16E-GTS)

Click here

10. INSPECT POWER WINDOW OPERATION

for TMC Made: Click here

except TMC Made: Click here

11. PERFORM DIAGNOSTIC SYSTEM CHECK (for TMMMS Made)

Click here

12. INSPECT SRS WARNING LIGHT

for TMC Made: Click here

for TMMMS Made: Click here

13. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click here