- Brake warning light / red (malfunction) illuminates*
- ABS warning light illuminates
- Slip indicator light illuminates
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000265UV |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMMMS Made): VEHICLE CONTROL HISTORY (RoB); 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022] | ||
VEHICLE CONTROL HISTORY (RoB)
DESCRIPTION
- Vehicle Control History (RoB) is a function that captures and stores ECU data when triggered by specific vehicle behavior.
- It may be possible to determine the cause of the malfunction by checking the vehicle history information and freeze frame data.
- The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.
-
The stored data items for Vehicle Control History (RoB) Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.
Click here
![2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMMMS Made): DATA LIST / ACTIVE TEST](/t3Portal/stylegraphics/info.gif)
PRECAUTIONS
- As Vehicle Control History (RoB) may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History (RoB) before performing any inspections.
- As Vehicle Control History (RoB) may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History (RoB) before returning the vehicle to the customer.
CHECK VEHICLE CONTROL HISTORY (RoB) (ELECTRONICALLY CONTROLLED BRAKE SYSTEM
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / Brake / Utility / Vehicle Control History (RoB).
Chassis > Brake > Utility
|
Tester Display |
|---|
|
Vehicle Control History (RoB) |
Vehicle Control History (RoB) Item
|
Code |
Tester Display |
Measurement Item |
User Notification |
Diagnostic Note |
|---|---|---|---|---|
|
X0451 |
FL Speed Sensor Wrong Installation |
History of front speed sensor LH being installed incorrectly |
|
Refer to FL Speed Sensor Wrong Installation (X0451).
|
|
X0452 |
FR Speed Sensor Wrong Installation |
History of front speed sensor RH being installed incorrectly |
|
Refer to FR Speed Sensor Wrong Installation (X0452).
|
|
X0453 |
RL Speed Sensor Wrong Installation |
History of rear speed sensor LH being installed incorrectly |
|
Refer to RL Speed Sensor Wrong Installation (X0453).
|
|
X0454 |
RR Speed Sensor Wrong Installation |
History of rear speed sensor RH being installed incorrectly |
|
Refer to RR Speed Sensor Wrong Installation (X0454).
|
|
X0455 |
Steering Angle Sensor Wrong Installation |
History of steering angle sensor being installed incorrectly |
Slip indicator light illuminates |
- |
|
X0456 |
Yaw Rate Sensor Wrong Installation |
History of yaw rate sensor (airbag sensor assembly) being installed incorrectly |
Slip indicator light illuminates |
Refer to Yaw Rate Sensor Wrong Installation (X0456).
|
|
X2079 |
Communication Error from Brake Control Module to Engine Control Module |
History of receiving an invalid communication signal from ECM |
Slip indicator light illuminates |
|
|
X2086 |
SRS Airbag Malfunction |
History of receiving an abnormal secondary collision brake control request signal from airbag sensor assembly |
- |
Refer to How to Proceed with Troubleshooting in Airbag System.
|
|
X2087 |
Engine Malfunction |
History of receiving an SFI system abnormal signal from ECM |
Slip indicator light illuminates |
Refer to How to Proceed with Troubleshooting in SFI System. for 2ZR-FAE:
for M20A-FKS:
|
|
X208A |
Zero Point Calibration of Steering Angle Sensor Initialization Malfunction |
History of failure in acquiring steering angle zero point even after the vehicle is driven in a straight line at a vehicle speed of 15 km/h (9 mph) or more for 115 seconds or more with the steering angle sensor zero point calibration cleared |
Slip indicator light illuminates |
Refer to Zero Point Calibration of Steering Angle Sensor Initialization Malfunction (X208A).
|
|
X2096 |
Pre-Collision Brake |
History of pre-collision brake operation |
In accordance with Pre-collision System behavior |
- |
|
X2098 |
Pre-Collision Brake Assist |
History of pre-collision brake assist operation |
In accordance with Pre-collision System behavior |
- |
|
X20A0 |
ABS |
History of ABS operation |
- |
- |
|
X20A1 |
VSC |
History of VSC operation |
Slip indicator light blinks |
- |
|
X20A2 |
TRC(TRAC) |
History of TRC operation |
Slip indicator light blinks |
- |
|
X20A5 |
Hill Start Assist |
History of hill start assist operation |
- |
- |
|
X20A7 |
Brake Assist |
History of brake assist operation |
- |
- |
|
X20A8 |
Secondary Collision Brake |
History of secondary collision brake operation |
- |
- |
|
X20A9 |
ABS Continuous Operation Request |
History of ABS being operated for 60 seconds or more |
|
- |
|
X20AA |
VSC Continuous Operation Request |
History of VSC being operated for 10 seconds or more |
|
- |
|
X2105 |
Shift N Switch Malfunction |
History of receiving an abnormal neutral position switch signal via CAN communication |
- |
- |
-
*: The brake warning light / red (malfunction) illuminates when any of the following vehicle conditions are met:
- When EBD is prohibited
- When a malfunction has occurred
- When failure compensation control is prohibited
CLEAR VEHICLE CONTROL HISTORY (RoB) (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / Brake / Utility / Vehicle Control History (RoB).
Chassis > Brake > Utility
|
Tester Display |
|---|
|
Vehicle Control History (RoB) |
(f) Press the DTC clear button.
NOTICE:
By performing this procedure, all stored Vehicle Control History (RoB) items will be cleared.
VEHICLE CONTROL HISTORY (RoB) (AIRBAG SYSTEM)
HINT:
A part of the control history can be confirmed using the vehicle control history (RoB).
Click here
|
|