BRAKE SYSTEM (OTHER): BRAKE FLUID (for HV Model): BLEEDING; 2023 - 2025 MY Corolla Corolla HV [09/2022

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM10000000265CF
Model Year Start: 2023	Model: Corolla	Prod Date Range: [09/2022 - ]
Title: BRAKE SYSTEM (OTHER): BRAKE FLUID (for HV Model): BLEEDING; 2023 - 2025 MY Corolla Corolla HV [09/2022 - ]

BLEEDING

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake fluid bleeding are shown below.

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

CAUTION / NOTICE / HINT

NOTICE:

Move the shift lever to P and apply the parking brake before bleeding the brakes.
Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.
If brake fluid leaks onto any painted surface, immediately wash it off.
Do not operate the brake actuator assembly while air is in the brake system or in the brake master cylinder sub-assembly. Doing so may cause air to enter the brake actuator assembly.
If bleeding the brake actuator assembly is difficult due to air in the brake actuator assembly, replace it with a new one.
Do not operate the brake pedal with 2 or more breeder plugs open.

HINT:

If any work is performed on the brake system or if air in the brake lines is suspected, bleed the air from the brake system.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

3. REMOVE CENTER COWL TOP VENTILATOR LOUVER

(a) Disengage the 2 clips (A) as shown in the illustration.

*a	Clip (A)
*b	Clip (B)
	Remove in this Direction

(b) Disengage the clip (B) and separate the hood to cowl top seal from the cowl top ventilator louver sub-assembly.

(c) Disengage the 2 claws and 2 guides to remove the center cowl top ventilator louver from the cowl top ventilator louver sub-assembly.

4. REMOVE BRAKE MASTER CYLINDER RESERVOIR FILLER CAP ASSEMBLY

(a) Remove the brake master cylinder reservoir filler cap assembly.

5. FILL RESERVOIR WITH BRAKE FLUID

(a) Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT3

SAE J1704 or FMVSS No. 116 DOT4

NOTICE:

Make sure that there is sufficient brake fluid in the reservoir.
Do not remove the filter from the brake master cylinder reservoir assembly and be sure to fill the brake master cylinder reservoir assembly with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.

HINT:

When replacing the brake fluid, the brake fluid bottle can be inverted and placed on the reservoir filler opening.

6. BLEED BRAKE LINE

(a) Remove the bleeder plug cap.

(b) Connect a vinyl tube to the bleeder plug.

NOTICE:

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while replacing the brake fluid.
Do not operate the brake pedal with 2 or more breeder plugs open.

(d) When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2

(e) Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.

(f) Tighten the bleeder plug completely.

Torque:

8.3 N·m {85 kgf·cm, 73 in·lbf}

(g) Install the bleeder plug cap.

(h) Repeat the above steps to bleed the brake fluid of the brake lines for each wheel.

7. INSPECT FOR BRAKE FLUID LEAK

8. ADJUST BRAKE FLUID LEVEL IN RESERVOIR

Click here

9. INSTALL BRAKE MASTER CYLINDER RESERVOIR FILLER CAP ASSEMBLY

(a) Install the brake master cylinder reservoir filler cap assembly.

10. INSTALL CENTER COWL TOP VENTILATOR LOUVER

(a) Engage the 2 guides and 2 claws to install the center cowl top ventilator louver to the cowl top ventilator louver sub-assembly.

(b) Engage the clip (B) and install the hood to cowl top seal to the cowl top ventilator louver sub-assembly.

*a	Clip (A)
*b	Clip (B)
	Install in this Direction

11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

12. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here