| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000002612E |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: LIGHTING (INT): LIGHTING SYSTEM (for TMMMS Made): Door Unlock Detection Switch Circuit; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
|
Door Unlock Detection Switch Circuit |
DESCRIPTION
The main body ECU (multiplex network body ECU) detects the condition of each door unlock detection switch.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.*
Click here
![2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): REGISTRATION](/t3Portal/stylegraphics/info.gif)
- *: w/ Smart Key System
PROCEDURE
|
1. |
CONFIRM MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
for Sedan without Unlock Detection Switch (for Rear Door Lock with Motor Assembly) |
A |
|
w/ Unlock Detection Switch (for Rear Door Lock with Motor Assembly) |
B |
| B |
|
|
|
2. |
READ VALUE USING TECHSTREAM |
(a) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
FR Door Lock Pos |
Front door RH unlock detection switch signal |
LOCK or UNLOCK |
LOCK: Front door RH locked UNLOCK: Front door RH unlocked |
- |
|
FL Door Lock Pos |
Front door LH unlock detection switch signal |
LOCK or UNLOCK |
LOCK: Front door LH locked UNLOCK: Front door LH unlocked |
- |
Body Electrical > Main Body > Data List
|
Tester Display |
|---|
|
FR Door Lock Pos |
|
FL Door Lock Pos |
OK:
Normal conditions listed above are displayed.
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG ("FL Door Lock Pos" is not normal) |
B |
|
NG ("FR Door Lock Pos" is not normal) |
C |
| A |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| B |
|
| C |
|
|
3. |
READ VALUE USING TECHSTREAM |
(a) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
FR Door Lock Pos |
Front door RH unlock detection switch signal |
LOCK or UNLOCK |
LOCK: Front door RH locked UNLOCK: Front door RH unlocked |
- |
|
FL Door Lock Pos |
Front door LH unlock detection switch signal |
LOCK or UNLOCK |
LOCK: Front door LH locked UNLOCK: Front door LH unlocked |
- |
|
RR-Door Lock Pos SW |
Rear door RH unlock detection switch signal |
OFF or ON |
OFF: Rear door RH locked ON: Rear door RH unlocked |
- |
|
RL-Door Lock Pos SW |
Rear door LH unlock detection switch signal |
OFF or ON |
OFF: Rear door LH locked ON: Rear door LH unlocked |
- |
Body Electrical > Main Body > Data List
|
Tester Display |
|---|
|
FR Door Lock Pos |
|
FL Door Lock Pos |
|
RR-Door Lock Pos SW |
|
RL-Door Lock Pos SW |
OK:
Normal conditions listed above are displayed.
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG ("FL Door Lock Pos" is not normal) |
B |
|
NG ("FR Door Lock Pos" is not normal) |
C |
|
NG ("RL-Door Lock Pos SW" and "RR-Door Lock Pos SW" are not normal) |
D |
| A |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| C |
|
| D |
|
|
|
4. |
INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH |
(a) Inspect the front door lock with motor assembly LH.
Click here
| NG |
|
|
|
5. |
CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND) |
(a) Disconnect the 4F instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
L4-8 (LSSR) - 4F-13 |
Always |
Below 1 Ω |
|
L4-8 (LSSR) or 4F-13 - Body ground |
Always |
10 kΩ or higher |
|
L4-7 (E) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6. |
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
4F-13 - MB-19 (LSFL) |
Always |
Below 1 Ω |
| OK |
|
| NG |
|
|
7. |
INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH |
(a) Inspect the front door lock with motor assembly RH.
Click here
| NG |
|
|
|
8. |
CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND) |
(a) Disconnect the 4F instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K5-7 (LSSR) - 4F-12 |
Always |
Below 1 Ω |
|
K5-7 (LSSR) or 4F-12 - Body ground |
Always |
10 kΩ or higher |
|
K5-8 (E) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
4F-12 - MB-17 (LSFR) |
Always |
Below 1 Ω |
| OK |
|
| NG |
|
|
10. |
INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH |
(a) Inspect the rear door lock with motor assembly LH.
Click here
| NG |
|
|
|
11. |
INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH |
(a) Inspect the rear door lock with motor assembly RH.
Click here
| NG |
|
|
|
12. |
CHECK HARNESS AND CONNECTOR (REAR DOOR LOCK WITH MOTOR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND) |
(a) Disconnect the 4F instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N1-6 (LSSR) - 4F-14 |
Always |
Below 1 Ω |
|
N1-9 (E) - Body ground |
Always |
Below 1 Ω |
|
M1-6 (LSSR) - 4F-14 |
Always |
Below 1 Ω |
|
M1-9 (E) - Body ground |
Always |
Below 1 Ω |
|
N1-6 (LSSR), M1-6 (LSSR) or 4F-14 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
13. |
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
4F-14 - MB-5 (LSR) |
Always |
Below 1 Ω |
| OK |
|
| NG |
|
|
|