Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM10000000260TW
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 -           ]
Title: G16E-GTS (ENGINE MECHANICAL): CYLINDER HEAD: INSPECTION; 2023 - 2025 MY GR Corolla [09/2022 -        ]

INSPECTION

PROCEDURE

1. INSPECT CYLINDER HEAD SUB-ASSEMBLY

(a) Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces where the cylinder head sub-assembly contacts the cylinder block sub-assembly, intake manifold and turbocharger sub-assembly side.

*a

Bottom Side

*b

Intake Manifold Side

*c

Turbocharger Sub-assembly Side

-

-

Maximum Warpage:

Item

Specified Condition

Bottom side

0.05 mm (0.00197 in.)

Intake manifold side

0.10 mm (0.00394 in.)

Turbocharger Sub-assembly Side

0.10 mm (0.00394 in.)

HINT:

If the warpage is more than the maximum, replace the cylinder head sub-assembly.

(b) Using a dye penetrant, check the intake ports, exhaust ports and cylinder head sub-assembly surface for cracks.

HINT:

If cracks are found, replace the cylinder head sub-assembly.

2. INSPECT COMPRESSION SPRING

(a) Intake Side:

(1) Using a vernier caliper, measure the free length of the compression spring.

Standard Free Length:

57.70 mm (2.27 in.)

NOTICE:

Compression springs come in 2 different lengths. Make sure all compression springs are the same length when replacing them.

(2) Using a steel square, measure the deviation of the compression spring.

Maximum Deviation (Reference):

1.0 mm (0.0394 in.)

HINT:

If the deviation is more than the maximum, replace the compression spring.

*a

Deviation

*b

37 mm (1.46 in.)

(b) Exhaust Side:

(1) Using a vernier caliper, measure the free length of the compression spring.

Standard Free Length:

59.11 mm (2.33 in.)

NOTICE:

Compression springs come in 2 different lengths. Make sure all compression springs are the same length when replacing them.

(2) Using a steel square, measure the deviation of the compression spring.

Maximum Deviation (Reference):

1.0 mm (0.0394 in.)

HINT:

If the deviation is more than the maximum, replace the compression spring.

*a

Deviation

*b

37 mm (1.46 in.)

3. INSPECT INTAKE VALVE

(a) Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.470 to 5.485 mm (0.215 to 0.216 in.)

HINT:

If the valve stem diameter is not as specified, check the intake valve guide bush oil clearance.

*a

35 mm (1.38 in.)

*b

70 mm (2.76 in.)

(b) Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)

Minimum Margin Thickness:

0.5 mm (0.0197 in.)

HINT:

If the margin thickness is less than the minimum, replace the intake valve.

*a

Margin Thickness

(c) Using a vernier caliper, measure the overall length of the intake valve.

Standard Overall Length:

113.63 mm (4.47 in.)

Minimum Overall Length:

113.13 mm (4.45 in.)

HINT:

If the overall length is less than the minimum, replace the intake valve.

*a

Overall Length

4. INSPECT EXHAUST VALVE

(a) Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:

5.465 to 5.480 mm (0.215 to 0.216 in.)

HINT:

If the valve stem diameter is not as specified, check the exhaust valve guide bush oil clearance.

*a

35 mm (1.38 in.)

*b

70 mm (2.76 in.)

(b) Using a vernier caliper, measure the valve head margin thickness.

Standard Margin Thickness:

1.0 mm (0.0394 in.)

Minimum Margin Thickness:

0.5 mm (0.0197 in.)

HINT:

If the margin thickness is less than the minimum, replace the exhaust valve.

*a

Margin Thickness

(c) Using a vernier caliper, measure the overall length of the exhaust valve.

Standard Overall Length:

117.05 mm (4.608 in.)

Minimum Overall Length:

116.55 mm (4.59 in.)

HINT:

If the overall length is less than the minimum, replace the exhaust valve.

*a

Overall Length

5. INSPECT VALVE GUIDE BUSH OIL CLEARANCE

(a) Using a caliper gauge, measure the inside diameter of the valve guide bush.

Standard Valve Guide Bush Inside Diameter:

5.51 to 5.53 mm (0.217 to 0.218 in.)

(b) Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:

Item

Specified Condition

Intake Side

0.025 to 0.060 mm (0.000984 to 0.00236 in.)

Exhaust Side

0.030 to 0.065 mm (0.00118 to 0.00256 in.)

Maximum Oil Clearance:

Item

Specified Condition

Intake Side

0.080 mm (0.00315 in.)

Exhaust Side

0.10 mm (0.00394 in.)

HINT:

  • Oil clearance = Valve guide bush inside - Valve stem diameter
  • If the oil clearance is more than the maximum, replace the valve and valve guide bush.

6. INSPECT INTAKE VALVE SEAT

(a) Apply a light coat of Prussian blue to the valve face.

(b) Lightly press the valve face against the intake valve seat.

NOTICE:

Do not rotate the valve while pressing it.

*a

Width

(c) Check the valve face and intake valve seat by using the following procedure:

(1) If Prussian blue appears 360° around the entire intake valve face, the valve face is concentric.

HINT:

If the valve face is not concentric, replace the intake valve.

(2) If Prussian blue appears 360° around the entire intake valve seat, the intake valve seat and valve face are concentric.

HINT:

If the valve face is not concentric, resurface the intake valve seat.

(3) Measure the width of the contact area of the intake valve seat and valve face.

Standard Width:

1.0 to 1.4 mm (0.0394 to 0.0551 in.)

7. INSPECT EXHAUST VALVE SEAT

(a) Apply a light coat of Prussian blue to the valve face.

(b) Lightly press the valve face against the exhaust valve seat.

NOTICE:

Do not rotate the valve while pressing it.

*a

Width

(c) Check the valve face and exhaust valve seat by using the following procedure:

(1) If Prussian blue appears 360° around the entire exhaust valve face, the valve face is concentric.

HINT:

If the valve face is not concentric, replace the exhaust valve.

(2) If Prussian blue appears 360° around the entire exhaust valve seat, the exhaust valve seat and valve face are concentric.

HINT:

If the valve face is not concentric, resurface the exhaust valve seat.

(3) Measure the width of the contact area of the exhaust valve seat and valve face.

Standard Width:

1.3 to 1.7 mm (0.0512 to 0.0669 in.)

8. INSPECT CAMSHAFT THRUST CLEARANCE

(a) Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 5 camshaft bearing cap, No. 6 camshaft bearing cap, 6 No. 4 camshaft bearing caps, camshaft journals.

(b) Place the intake camshaft sub-assembly and exhaust camshaft sub-assembly on the cylinder head sub-assembly.

(c) Install the camshaft bearing caps.

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE MECHANICAL): ENGINE UNIT: REASSEMBLY+

(d) Using a dial indicator, measure the thrust clearance while moving the intake camshaft sub-assembly and exhaust camshaft sub-assembly back and forth.

Standard Thrust Clearance:

Item

Specified Condition

Intake camshaft sub-assembly

0.04 to 0.17 mm (0.00157 to 0.00669 in.)

Exhaust camshaft sub-assembly

0.04 to 0.17 mm (0.00157 to 0.00669 in.)

Maximum Thrust Clearance:

Item

Specified Condition

Intake camshaft sub-assembly

0.22 mm (0.00866 in.)

Exhaust camshaft sub-assembly

0.22 mm (0.00866 in.)

HINT:

If the thrust clearance is more than the maximum, replace the cylinder head sub-assembly. If the thrust surface is damaged, replace the camshaft.