Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000260TN
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: G16E-GTS (ENGINE MECHANICAL): ENGINE ASSEMBLY: INSTALLATION; 2023 MY GR Corolla [09/2022 - 11/2022]

INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

PROCEDURE

1. INSTALL ENGINE HANGER

Click here 2023 MY GR Corolla [09/2022 - 11/2022]; G16E-GTS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

2. REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

(a) Remove the engine assembly from the engine stand.

3. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE MECHANICAL): REAR CRANKSHAFT OIL SEAL: INSTALLATION+

4. INSTALL FLYWHEEL SUB-ASSEMBLY

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE MECHANICAL): REAR CRANKSHAFT OIL SEAL: INSTALLATION+

5. INSTALL COVER AND DISC CLUTCH SET

Click here 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; CLUTCH: CLUTCH UNIT (for EA67F / EA68F): INSTALLATION+

6. INSTALL MANUAL TRANSAXLE ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; EA67F / EA68F (MANUAL TRANSMISSION / TRANSAXLE): MANUAL TRANSAXLE ASSEMBLY: INSTALLATION+

7. INSTALL PROPELLER SHAFT HEAT INSULATOR

Click here 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; EA67F / EA68F (MANUAL TRANSMISSION / TRANSAXLE): MANUAL TRANSAXLE ASSEMBLY: INSTALLATION+

8. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (EMISSION CONTROL): MONOLITHIC CONVERTER: INSTALLATION+

9. INSTALL ENGINE WIRE

(a) Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.

(b) Install the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(c) Install the 4 bolts.

Torque:

Bolt (A) :

10 N·m {102 kgf·cm, 7 ft·lbf}

Bolt (B) :

20 N·m {204 kgf·cm, 15 ft·lbf}

(d) Install the 4 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

10. INSTALL GENERATOR ASSEMBLY

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (BATTERY / CHARGING): GENERATOR: INSTALLATION+

11. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

(a) Install the V-ribbed belt tensioner assembly with the 2 bolts.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

12. INSTALL FAN AND GENERATOR V BELT

Click here 2023 MY GR Corolla [09/2022 - 11/2022]; MAINTENANCE: G16E-GTS DRIVE BELT: INSTALLATION+

13. INSTALL FLYWHEEL HOUSING UNDER COVER

(a) Align the claw of the flywheel housing under cover with the notch of the cylinder block sub-assembly then install.

NOTICE:

Make sure that the orientation is correct when installing.

14. INSTALL STARTER ASSEMBLY

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (STARTING): STARTER: INSTALLATION+

15. INSTALL FLYWHEEL HOUSING SIDE COVER

(a) Install the flywheel housing side cover to the cylinder block sub-assembly.

16. INSTALL NO. 1 FUEL VAPOR FEED HOSE

(a) Engage the 2 clamps.

(b) Install the No. 1 fuel vapor feed hose to the purge valve (purge VSV).

17. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.

(a) Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.

*a

Temporarily Tighten

(b) Install the 2 bolts and nut in the order shown in the illustration.

Torque:

72 N·m {734 kgf·cm, 53 ft·lbf}

(c) Connect the air conditioner tube with the clamp.

18. INSTALL RESERVE TANK ASSEMBLY

(a) Install the bolt and reserve tank assembly to the vehicle.

Torque:

5.0 N·m {51 kgf·cm, 44 in·lbf}

(b) Connect the No. 3 water by-pass hose to the reserve tank assembly and slide the clip to secure it.

19. INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.

(a) Temporarily install the engine mounting insulator LH to the vehicle.

*a

Temporarily Tighten

(b) Install the 4 bolts and nut in the order shown in the illustration.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

(c) Engage the clamp.

20. REMOVE ENGINE HANGER

Click here 2023 MY GR Corolla [09/2022 - 11/2022]; G16E-GTS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

21. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

(a) Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:

  • Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.
  • Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
  • To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly with transaxle.

(b) Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.

NOTICE:

  • Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
  • While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.

(c) Connect the front suspension crossmember sub-assembly to the vehicle with the 4 bolts.

Torque:

141 N·m {1438 kgf·cm, 104 ft·lbf}

(d) Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 3 bolts in the order shown illustration.

Torque:

72 N·m {734 kgf·cm, 53 ft·lbf}

(e) Install the engine mounting insulator LH to the transaxle assembly with the 4 bolts in the order shown illustration.

Torque:

52 N·m {530 kgf·cm, 38 ft·lbf}

22. CONNECT NO. 1 CLUTCH HOSE

(a) Connect the No. 1 clutch hose to the clutch flexible hose bracket with a new clip.

*a

10 mm Union Nut Wrench

*b

Torque Wrench Fulcrum Length

(b) Using a 10 mm union nut wrench, connect the bleeder clutch release tube to the No. 1 clutch hose.

Torque:

Specified tightening torque :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

23. INSTALL NO. 1 AIR TUBE

(a) Tighten the 2 hose clamps to install the No. 1 air tube.

Torque:

6.0 N·m {61 kgf·cm, 53 in·lbf}

24. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

(a) Install the rear side rail reinforcement sub-assembly RH to the front suspension crossmember sub-assembly and vehicle body with the 6 bolts.

Torque:

Bolt (A) :

70 N·m {714 kgf·cm, 52 ft·lbf}

Bolt (B) :

7.0 N·m {71 kgf·cm, 62 in·lbf}

25. INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

(a) Install the rear side rail reinforcement sub-assembly LH to the front suspension crossmember sub-assembly and vehicle body with the 4 bolts.

Torque:

70 N·m {714 kgf·cm, 52 ft·lbf}

26. INSTALL DRIVE SHAFT ASSEMBLY

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; DRIVE SHAFT / PROPELLER SHAFT: FRONT DRIVE SHAFT ASSEMBLY (for G16E-GTS): INSTALLATION

27. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; DRIVE SHAFT / PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY: INSTALLATION

28. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION+

29. INSTALL COLUMN HOLE COVER SILENCER SHEET

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION+

30. CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Click here 2023 MY GR Corolla [09/2022 - 11/2022]; HEATING / AIR CONDITIONING: COMPRESSOR (for G16E-GTS): INSTALLATION+

31. CONNECT SUCTION HOSE SUB-ASSEMBLY

Click here 2023 MY GR Corolla [09/2022 - 11/2022]; HEATING / AIR CONDITIONING: COMPRESSOR (for G16E-GTS): INSTALLATION+

32. CONNECT FUEL TUBE SUB-ASSEMBLY

(a) Connect the fuel tube sub-assembly to the fuel pipe.

Click here 2023 MY GR Corolla [09/2022 - 11/2022]; G16E-GTS (FUEL): FUEL SYSTEM: PRECAUTION

(b) Install the No. 1 fuel pipe clamp to the fuel tube sub-assembly.

33. CONNECT INLET HEATER WATER HOSE

(a) Connect the inlet heater water hose to the No. 1 water by-pass pipe and slide the clip to secure it.

34. CONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

(a) Connect the No. 3 water by-pass hose to the No. 3 water by-pass pipe and slide the clip to secure it.

35. CONNECT NO. 1 FUEL VAPOR FEED HOSE

(a) Connect the No. 1 fuel vapor feed hose to the fuel tank to canister tube.

36. CONNECT NO. 2 WATER BY-PASS HOSE

(a) Connect the No. 2 water by-pass hose to the No. 4 water by-pass pipe and slide the clip to secure it.

37. CONNECT NO. 1 WATER BY-PASS HOSE

(a) Connect the No. 1 water by-pass hose to the No. 4 water by-pass pipe and slide the clip to secure it.

38. CONNECT UNION TO CONNECTOR TUBE HOSE

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; BRAKE SYSTEM (OTHER): VACUUM PUMP (for G16E-GTS): INSTALLATION+

39. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

(a) Connect the transmission control cable assembly to the control cable bracket assembly with 2 new clips (B).

NOTICE:

Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.

*a

Paint Mark

*b

Clip

*c

Washer

(b) Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips (A).

40. INSTALL ECM

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): ECM: INSTALLATION+

41. INSTALL NO. 2 AIR TUBE

(a) Install the No. 2 air tube with the bolt.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

(b) Tighten the 2 hose clamps.

Torque:

6.0 N·m {61 kgf·cm, 53 in·lbf}

42. CONNECT NO. 2 RADIATOR HOSE

(a) Connect the No. 2 radiator hose to the water inlet with thermostat sub-assembly and slide the clip to secure it.

43. CONNECT NO. 1 RADIATOR HOSE

(a) Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.

44. CONNECT ENGINE WIRE

(a) Engage the 2 clamps to connect the engine wire to the vehicle.

(b) Connect the engine wire to the vehicle with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(c) Connect the 3 connectors to the engine room relay block.

(d) Install the nut.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(e) Install the nut.

Torque:

7.6 N·m {77 kgf·cm, 67 in·lbf}

45. INSTALL COVER RELAY BLOCK UPR

(a) Install the junktion block cover.

46. INSTALL NO. 1 RELAY BLOCK COVER

(a) Install the No. 1 relay block cover.

47. INSTALL AIR CLEANER BRACKET

(a) Install the air cleaner bracket with the 2 bolts.

Torque:

7.0 N·m {71 kgf·cm, 62 in·lbf}

(b) Engage the clamp to the air cleaner bracket.

48. INSTALL AIR CLEANER WITH AIR CLEANER HOSE

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (EMISSION CONTROL): MONOLITHIC CONVERTER: INSTALLATION+

49. INSTALL NO. 1 AIR CLEANER INLET

50. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

(a) Engage the 4 clamps to install the No. 1 engine cover sub-assembly.

NOTICE:

  • Securely engage the clamps.
  • If the clamps are forcibly engaged or struck with an object, they may be damaged.

51. INSTALL RADIATOR SUPPORT OPENING COVER

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 08/2023]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Hatchback, GR): INSTALLATION+

52. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; MAINTENANCE: G16E-GTS BATTERY: INSTALLATION+

53. INSTALL SPARE WHEEL CUSHION

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; INTERIOR PANELS / TRIM: ROOF HEADLINING (for Hatchback): INSTALLATION+

54. INSTALL DECK BOARD ASSEMBLY

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; INTERIOR PANELS / TRIM: ROOF HEADLINING (for Hatchback): INSTALLATION+

55. BLEED CLUTCH LINE

Click here 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; CLUTCH: CLUTCH SYSTEM (for EA67F / EA68F): BLEEDING+

56. ADD ENGINE OIL

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; MAINTENANCE: G16E-GTS OIL AND OIL FILTER: REPLACEMENT+

57. ADD ENGINE COOLANT

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; MAINTENANCE: G16E-GTS COOLANT: REPLACEMENT+

58. ADD MANUAL TRANSAXLE OIL

Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; MAINTENANCE: EA67F / EA68F MANUAL TRANSAXLE OIL: REPLACEMENT+

59. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Click here 2021 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2020 -        ]; HEATING / AIR CONDITIONING: REFRIGERANT (for HFO-1234yf(R1234yf)): REPLACEMENT+

60. WARM UP ENGINE

Click here 2021 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2020 -        ]; HEATING / AIR CONDITIONING: REFRIGERANT (for HFO-1234yf(R1234yf)): REPLACEMENT+

61. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; EA67F / EA68F (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE: ADJUSTMENT+

62. INSPECT FOR ENGINE OIL LEAK

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; MAINTENANCE: G16E-GTS OIL AND OIL FILTER: REPLACEMENT+

63. INSPECT MANUAL TRANSAXLE OIL LEAK

64. INSPECT FOR COOLANT LEAK

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (COOLING): COOLING SYSTEM: ON-VEHICLE INSPECTION+

65. INSPECT FOR REFRIGERANT LEAK

Click here 2021 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2020 -        ]; HEATING / AIR CONDITIONING: REFRIGERANT (for HFO-1234yf(R1234yf)): REPLACEMENT+

66. INSPECT FOR FUEL LEAK

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (FUEL): FUEL SYSTEM: ON-VEHICLE INSPECTION+

67. INSPECT FOR EXHAUST GAS LEAK

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (INTAKE / EXHAUST): EXHAUST PIPE: INSTALLATION+

68. CHECK ENGINE OIL LEVEL

Click here 2023 MY GR Corolla [09/2022 - 08/2023]; G16E-GTS (LUBRICATION): LUBRICATION SYSTEM: ON-VEHICLE INSPECTION+

69. INSPECT RADIATOR RESERVE TANK ENGINE COOLANT LEVEL

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (COOLING): COOLING SYSTEM: ON-VEHICLE INSPECTION+

70. INSTALL REAR ENGINE UNDER COVER LH

(a) Install the rear engine under cover LH to the vehicle with the screw and 5 clips.

71. INSTALL REAR ENGINE UNDER COVER RH

(a) Install the rear engine under cover RH to the vehicle with the screw and 5 clips.

72. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

(a) Install the No. 1 engine under cover assembly to the vehicle with the 4 bolts and 10 clips.

Torque:

7.5 N·m {76 kgf·cm, 66 in·lbf}

73. INSTALL FRONT WHEELS

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; MAINTENANCE: TIRE AND WHEEL: INSTALLATION

74. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

75. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT

76. PERFORM INITIALIZATION

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

77. INSPECT IGNITION TIMING

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE MECHANICAL): ENGINE: ON-VEHICLE INSPECTION+

78. INSPECT ENGINE IDLE SPEED

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE MECHANICAL): ENGINE: ON-VEHICLE INSPECTION+

79. INSPECT CO/HC

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE MECHANICAL): ENGINE: ON-VEHICLE INSPECTION+

80. CHECK SPEED SENSOR SIGNAL

Click here 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMC Made): TEST MODE PROCEDURE