- Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
- Smart Key System (for Gasoline Model, Entry Function)
- Smart Key System (for Gasoline Model, Start Function)
- Steering lock function*1
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM10000000260TA |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: G16E-GTS (ENGINE MECHANICAL): CAMSHAFT: REMOVAL; 2023 MY GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
| *1:w/ Steering Lock Function | |||
|
Replacement of ECM |
Perform Vehicle Identification Number (VIN) or frame number registration |
MIL illuminates |
|
|
ECU configuration |
- |
|
|
|
Update ECU security key |
Vehicle Control History (RoB) are stored |
|
|
|
Heavy Knock History |
- |
|
|
|
Code registration (Smart Key System (for Gasoline Model, Start Function)) |
|
|
|
|
Inspection After Repair |
|
|
|
Front wheel alignment adjustment |
|
|
|
|
Tire |
ECU Data Initialization (When performing tire replacement after RoB code X2104 is output) |
Active Torque Split AWD System |
|
NOTICE:
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
-
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power door lock control system
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
PROCEDURE
1. REMOVE NO. 3 CYLINDER BLOCK INSULATOR
Click here
2. REMOVE SPARK PLUG
Click here
3. REMOVE OIL PRESSURE AND TEMPERATURE SENSOR
Click here
4. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)
Click here
5. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)
Click here
6. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
Click here
7. REMOVE WATER INLET WITH WATER PUMP HOUSING SUB-ASSEMBLY
Click here
8. REMOVE OIL FILLER CAP ASSEMBLY
Click here
9. REMOVE CRANKSHAFT POSITION SENSOR
Click here
10. REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
Click here
11. REMOVE VACUUM PUMP ASSEMBLY
Click here
12. REMOVE CRANKSHAFT PULLEY ASSEMBLY
Click here
13. REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)
Click here
14. REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)
Click here
15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Click here
16. REMOVE SPARK PLUG TUBE GASKET
Click here
17. REMOVE ENGINE MOUNTING BRACKET RH
Click here
18. REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY
Click here
19. REMOVE TIMING CHAIN COVER OIL SEAL
Click here
20. REMOVE TIMING CHAIN COVER ASSEMBLY
Click here
21. SET VALVE TIMING
Click here
22. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Click here
23. REMOVE TIMING CHAIN GUIDE
Click here
24. REMOVE DAMPER PLATE SPACER
Click here
25. REMOVE CHAIN TENSIONER SLIPPER
Click here
26. REMOVE CHAIN SUB-ASSEMBLY
Click here
27. REMOVE NO. 1 CHAIN VIBRATION DAMPER
Click here
28. REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET
Click here
29. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Click here
30. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
Click here
31. REMOVE FUEL PUMP LIFTER GUIDE
Click here
32. REMOVE FUEL PUMP LIFTER HOUSING
Click here
33. REMOVE CAMSHAFT POSITION SENSOR HOLDER
Click here
34. REMOVE CAMSHAFT BEARING CAP
Click here
35. REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY
Click here
36. REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY
Click here
|
|