HEATING / AIR CONDITIONING: COMPRESSOR (for G16E-GTS): INSTALLATION; 2023 MY GR Corolla [09/2022

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM1000000025Z02
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [09/2022 - 11/2022]
Title: HEATING / AIR CONDITIONING: COMPRESSOR (for G16E-GTS): INSTALLATION; 2023 MY GR Corolla [09/2022 - 11/2022]

INSTALLATION

PROCEDURE

1. ADJUST COMPRESSOR OIL

(a) When replacing the compressor assembly with pulley with a new one, gradually discharge the inert gas (helium) from the service valve, and drain the following amount of oil before installation.

NOTICE:

If a new compressor assembly with pulley is installed without removing the same amount of compressor oil as is remaining in the pipes, the amount of compressor oil will be excessive. This prevents heat exchange in the refrigerant cycle and will cause the air conditioning system to malfunction.
A certain amount of compressor oil remains in the compressor assembly with pulley during circulation and the compressor may be damaged if the amount of compressor oil is more/less than this amount. Therefore, make sure to adjust the amount of compressor oil correctly.
If the amount of compressor oil remaining in the removed compressor assembly with pulley is excessively low, check for compressor oil leaks.
Do not race the engine before replacing the compressor assembly with pulley.
Make sure to use ND-OIL 12 or equivalent compressor oil.

(b) Remove the drain bolt (seal washer) from the removed compressor assembly with pulley.

*a	Drain Bolt (Seal Washer)

(c) Drain the compressor oil from the oil port of the removed compressor assembly with pulley as shown in the illustration.

NOTICE:

Make sure to drain the compressor oil from the oil port.

Oil Port

Turn Clockwise

(d) Remove the drain bolt (seal washer) from a new compressor assembly with pulley.

HINT:

The drain bolt (seal washer) can be reused.

*a	Drain Bolt (Seal Washer)

(e) Drain the following amount of compressor oil from the oil port of the new compressor assembly with pulley as shown in the illustration.

Standard:

(The amount of oil in a new compressor assembly with pulley: 70 (+15) cc (2.37 (+0.51) fl.oz)) - (The amount of oil in the removed compressor assembly with pulley) = The amount of oil to be removed from the new compressor assembly with pulley.

NOTICE:

Make sure to drain the compressor oil from the oil port.
Make sure to add the compressor oil from the oil port, not from the discharge or intake port.
If a tool is used to add compressor oil to the new compressor assembly with pulley, make sure that it is free of foreign matter.
If the amount of compressor oil remaining in the removed compressor assembly with pulley cannot be estimated because the compressor was damaged and oil was discharged due to a frontal collision, etc., install a new compressor assembly with pulley without removing any oil. If the cooler condenser assembly is also replaced, do not add the specified amount of compressor oil for cooler condenser assembly replacement (40 cc (1.35 fl.oz)).

Oil Port

Turn Clockwise

(f) Install the drain bolt (seal washer) to the new compressor assembly with pulley.

Torque:

30 N·m {306 kgf·cm, 22 ft·lbf}

NOTICE:

Make sure that there is no damage or foreign matter on the seal washer edge.

2. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

(a) Using an E8 "TORX" socket wrench, temporarily install the compressor assembly with pulley with the 2 stud bolts.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

(b) Install the compressor assembly with pulley with the 2 bolts and 2 nuts.

	Bolt
	Nut

Torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

3. CONNECT SUCTION HOSE SUB-ASSEMBLY

(a) Remove the vinyl tape from the suction hose sub-assembly.

(b) Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.

Compressor Oil:

ND-OIL 12 or equivalent

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(d) Connect the suction hose sub-assembly to the compressor assembly with pulley with the bolt.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

4. CONNECT DISCHARGE HOSE SUB-ASSEMBLY

(a) Remove the vinyl tape from the discharge hose sub-assembly.

(b) Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.

Compressor Oil:

ND-OIL 12 or equivalent

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.

(d) Connect the discharge hose sub-assembly to the compressor assembly with pulley with the bolt.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

5. INSTALL NO. 1 AIR TUBE

(a) Install the No. 1 air tube with the 2 bolts.

Torque:

7.0 N·m {71 kgf·cm, 62 in·lbf}

6. CONNECT NO. 3 AIR HOSE

(a) Connect the No. 3 air hose as shown in the illustration.

*a	Vehicle Right Side	*b	Marking (White)
*c	Marking (Blue)	*d	Clip Installation Angle (90°)

(b) Tighten the hose clamp.

Torque:

6.0 N·m {61 kgf·cm, 53 in·lbf}

7. CONNECT NO. 2 AIR HOSE

(a) Connect the No. 2 air hose as shown in the illustration.

*a	Vehicle Right Side	*b	Vehicle Front Side
*c	Marking (White)	*d	Clip Installation Angle (15°)
*e	Clip Installation Angle (30°)	-	-

(b) Tighten the hose clamp.

8. INSTALL V-RIBBED BELT

Click here

9. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Click here

10. WARM UP ENGINE

Click here

11. INSPECT FOR REFRIGERANT LEAK

Click here