Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM1000000025YV5
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 -           ]
Title: AXLE AND DIFFERENTIAL: REAR DIFFERENTIAL CARRIER ASSEMBLY: REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear differential carrier assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Replacement of 4WD linear solenoid (electro magnetic control coupling sub-assembly)

ECU Data Write (When replacing 4WD linear solenoid (electro magnetic control coupling sub-assembly))

Active Torque Split AWD System

2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; GF1A (TRANSFER / 4WD / AWD): ACTIVE TORQUE SPLIT AWD SYSTEM: CALIBRATION

Gas leaks from exhaust system

Inspection after repair

  • Poor idle, etc.
  • Engine start function, etc.

2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

Rear wheel alignment adjustment

  • Perform "Reset Memory"
  • Perform "Calibration"
  • VSC is disabled or malfunctions
  • DTCs are output
  • Slip indicator light illuminates
  • ABS warning light illuminates

2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMC Made): UTILITY

Tire

ECU Data Initialization (When performing tire replacement after RoB code X2104 is output)

Active Torque Split AWD System

2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; GF1A (TRANSFER / 4WD / AWD): ACTIVE TORQUE SPLIT AWD SYSTEM: CALIBRATION

CAUTION:

  • To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
  • The rear differential carrier assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the rear differential carrier assembly may fall off the engine lifter.

    *a

    An Object Exceeding Weight Limit of Engine Lifter

PROCEDURE

1. DRAIN DIFFERENTIAL OIL

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; MAINTENANCE: DIFFERENTIAL OIL: REPLACEMENT+

2. REMOVE REAR STABILIZER BAR

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; REAR SUSPENSION: REAR STABILIZER BAR (for Hatchback): REMOVAL

3. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; DRIVE SHAFT / PROPELLER SHAFT: PROPELLER SHAFT ASSEMBLY: REMOVAL

4. REMOVE UPPER MAIN MUFFLER HEAT INSULATOR

(a) Remove the 4 nuts and upper main muffler heat insulator from the vehicle body.

5. REMOVE REAR DRIVE SHAFT ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 -        ]; DRIVE SHAFT / PROPELLER SHAFT: REAR DRIVE SHAFT ASSEMBLY (for Gasoline Model): REMOVAL

6. LOOSEN REAR NO. 1 DIFFERENTIAL SUPPORT

HINT:

Loosen the bolts only when removal of the rear No. 1 differential support is required.

(a) Loosen the 2 bolts.

7. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY

NOTICE:

  • Do not damage the contact surface when removing the rear differential carrier assembly.
  • The remaining oil may leak out when removing the rear differential carrier assembly.
  • Securely support the rear differential carrier assembly while performing this step to avoid excessively tilting or dropping the rear differential carrier assembly.
  • Remove the bolts and nuts with the rear differential carrier assembly secured.

(a) Disconnect the vacuum hose from the electro magnetic control coupling sub-assembly.

(b) Support the rear differential carrier assembly with an engine lifter using 2 attachments or equivalent tools as shown in the illustration.

*1

Rear Lower Differential Mount Stopper

*a

Attachment

*b

Engine Lifter

(c) Remove the bolt (A) from the rear differential support.

(d) Remove the 2 bolts (B), and 2 rear lower differential mount stoppers from the rear No. 1 differential support.

(e) Remove the 2 bolts (C), 2 nuts from the rear No. 1 differential support.

HINT:

The nuts have tabs to prevent them from rotating.

(f) Disconnect the connector and disengage the clamp (A).

*1

Vacuum Hose

*a

Clamp (A)

*b

Clamp (B)

(g) Separate the vacuum hose from the clamp (B).

(h) Slightly lower the rear differential carrier assembly, remove the vacuum hose from the clamp.

NOTICE:

Do not damage the vacuum hose and electro magnetic control coupling wire harness.

HINT:

Lower the engine lifter to the extent that the vacuum hose can still be removed.

*1

Vacuum Hose

(i) Lower the rear differential carrier assembly slowly to remove the rear differential carrier assembly.

NOTICE:

  • Do not damage the vacuum hose and electro magnetic control coupling wire harness.
  • Move the engine lifter forward and backward as necessary to prevent the rear differential carrier assembly from contacting the rear suspension member sub-assembly.

8. REMOVE DAMPER (w/ Damper)

(a) Remove the bolt and damper from the rear No. 1 differential support.

9. REMOVE REAR UPPER DIFFERENTIAL MOUNT STOPPER

(a) Remove the 2 rear upper differential mount stoppers from the rear No. 1 differential support.

10. REMOVE REAR DIFFERENTIAL DYNAMIC DAMPER

(a) Remove the 2 bolts and rear differential dynamic damper from the rear differential support.

11. REMOVE REAR DIFFERENTIAL SUPPORT

(a) Remove the 3 bolts and rear differential support from the rear differential carrier assembly.