K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: DATA LIST / ACTIVE TEST; 2023 MY Corolla Corolla Hatchback [09/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000025YO1
Model Year Start: 2023	Model: Corolla Hatchback	Prod Date Range: [09/2022 - 11/2022]
Title: K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: DATA LIST / ACTIVE TEST; 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Warm up the engine.

(b) Turn the engine switch off.

(d) Turn the engine switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / Transmission / Data List.

(g) According to the display on the Techstream, read the Data List.

Powertrain > Transmission > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Total Distance Traveled	Total distance traveled	Min.: 0 Max.: 16777215	-	-
Total Distance Traveled - Unit	Unit for Total Distance Traveled	km or mile	-	-
Vehicle Speed	Vehicle speed	Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph)	Actual vehicle speed	The vehicle speed is detected using the wheel speed sensors. There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.
Engine Speed	Engine speed	Min.: 0 rpm Max.: 16383 rpm	750 to 850 rpm: Engine idling (shift lever in P, engine warmed up and A/C off)	When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Calculate Load	Load calculated by ECM	Min.: 0% Max.: 100%	-	This is the engine load calculated based on the estimated intake pressure. Calculate Load = Estimated intake pressure / maximum intake pressure x 100 (%) (For example, when the estimated intake pressure is the same as atmospheric pressure, Calculate Load is 100%.)
Coolant Temperature	Coolant temperature	Min.: -40°C (-40°F) Max.: 140°C (284°F)	75 to 100°C (167 to 212°F): After warming up	HINT: After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F). After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal. If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted. Check if the engine overheats if the value indicated is higher than 135°C (275°F).
Intake Air Temperature	Intake air temperature	Min.: -40°C (-40°F) Max.: 140°C (284°F)	Equivalent to temperature at location of mass air flow meter sub-assembly	HINT: After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal. If the value is -40°C (-40°F), or higher than 128°C (262°F), the sensor circuit is open or shorted.
Ambient Temperature	Ambient temperature	Min.: -40°C (-40°F) Max.: 215 °C (419 °F)	Equivalent to ambient air temperature	HINT: After a long soak, the engine coolant temperature, engine oil temperature, intake air temperature and ambient air temperature are approximately equal.
Engine Run Time	Engine run time	Min.: 0 sec. Max.: 65535 sec.	Time elapsed since engine started.	This is the time elapsed since the engine was started. HINT: The time is counted only while the engine is running.
Battery Voltage	Battery voltage	Min.: 0 V Max.: 65.5 V	11 to 14 V: Engine idling	If 11 V or less, characteristics of some electrical components may change.
IG2 / IGP	Status of IGP terminal	ON or OFF	ON: IGP ON OFF: IGP OFF	-
Glow Indicator Supported	Glow indicator supported	Unsupp or Supp	-	-
Throttle Position Sensor No.1 Voltage %	Absolute throttle position sensor (No. 1)	Min.: 0% Max.: 100%	10 to 22%: Accelerator pedal fully released 64 to 96%: Accelerator pedal fully depressed (engine running)	The No. 1 throttle position sensor output is converted using 5 V = 100%. HINT: If there are no throttle position sensor DTCs stored, it is possible to conclude that the throttle position sensor system is normal.
Starter SW	Starter signal	OFF or ON	ON: Starter operating OFF: Starter not operating	-
Shift SW Status (Neutral) Supported	Status of shift switch (neutral) supported	Unsupp or Supp	Unsupp	-
Stop Light SW	Stop light switch assembly status	OFF or ON	OFF: Brake pedal released ON: Brake pedal depressed	-
Complete Parts Monitor	Comprehensive component monitor	Not Avl or Avail	-	*2
Complete Parts Monitor Result	Comprehensive component monitor	Compl or Incmpl	-	*2
Ignition Monitor	Ignition monitor	Spark Ignition or Compression Ignition	-	-
Fuel System Monitor	Fuel system monitor	Not Avl or Avail	-	*2
Fuel System Monitor Result	Fuel system monitor	Compl or Incmpl	-	*2
Misfire Monitor	Misfire monitor	Not Avl or Avail	-	*2
Misfire Monitor Result	Misfire monitor	Compl or Incmpl	-	*2
EGR/VVT Monitor	EGR/VVT monitor	Not Avl or Avail	-	*2
EGR/VVT Monitor Result	EGR/VVT monitor	Compl or Incmpl	-	*2
A/F (O2) Sensor Heater Monitor	O2S (A/FS) heater monitor	Not Avl or Avail	-	*2
A/F (O2) Sensor Heater Monitor Result	O2S (A/FS) heater monitor	Compl or Incmpl	-	*2
A/F (O2) Sensor Monitor	O2S (A/FS) monitor	Not Avl or Avail	-	*2
A/F (O2) Sensor Monitor Result	O2S (A/FS) monitor	Compl or Incmpl	-	*2
Secondary Air Injection System Monitor	Secondary air injection system monitor	Not Avl or Avail	-	*2
Secondary Air Injection System Monitor Result	Secondary air injection system monitor	Compl or Incmpl	-	*2
EVAP Monitor	EVAP monitor	Not Avl or Avail	-	*2
EVAP Monitor Result	EVAP monitor	Compl or Incmpl	-	*2
Heated Catalyst Monitor	Heated catalyst monitor	Not Avl or Avail	-	*2
Heated Catalyst Monitor Result	Heated catalyst monitor	Compl or Incmpl	-	*2
Catalyst Monitor	Catalyst monitor	Not Avl or Avail	-	*2
Catalyst Monitor Result	Catalyst monitor	Compl or Incmpl	-	*2
Component Monitor ENA (Current)	Comprehensive component monitor	Unable or Enable	-	*3
Component Monitor Result (Current)	Comprehensive component monitor	Compl or Incmpl	-	*3
Ignition Monitor (Current)	Ignition monitor	Spark Ignition or Compression Ignition	-	-
Fuel System Monitor ENA (Current)	Fuel system monitor	Unable or Enable	-	*3
Fuel System Monitor Result (Current)	Fuel system monitor	Compl or Incmpl	-	*3
Misfire Monitor ENA (Current)	Misfire monitor	Unable or Enable	-	*3
Misfire Monitor Result (Current)	Misfire monitor	Compl or Incmpl	-	*3
EGR/VVT Monitor ENA (Current)	EGR monitor	Unable or Enable	-	*3
EGR/VVT Monitor Result (Current)	EGR monitor	Compl or Incmpl	-	*3
O2 Sensor Heater ENA (Current)	O2S (A/FS) heater monitor	Unable or Enable	-	*3
O2 Sensor Heater Monitor Result (Current)	O2S (A/FS) heater monitor	Compl or Incmpl	-	*3
A/F (O2) Sensor Monitor ENA (Current)	O2S (A/FS) monitor	Unable or Enable	-	*3
A/F (O2) Sensor Monitor Result (Current)	O2S (A/FS) monitor	Compl or Incmpl	-	*3
Secondary Air Injection System Monitor ENA (Current)	Secondary air injection system monitor	Unable or Enable	-	*3
Secondary Air Injection System Monitor Result (Current)	Secondary air injection system monitor	Compl or Incmpl	-	*3
EVAP Monitor ENA (Current)	EVAP monitor	Unable or Enable	-	*3
EVAP Monitor Result (Current)	EVAP monitor	Compl or Incmpl	-	*3
Heated Catalyst Monitor ENA (Current)	Heated catalyst monitor	Unable or Enable	-	*3
Heated Catalyst Monitor Result (Current)	Heated catalyst monitor	Compl or Incmpl	-	*3
Catalyst Monitor ENA (Current)	Catalyst monitor	Unable or Enable	-	*3
Catalyst Monitor Result (Current)	Catalyst monitor	Compl or Incmpl	-	*3
TC Terminal	TC terminal status	ON or OFF	OFF	-
MIL	MIL status	ON or OFF	OFF	-
MIL ON Run Distance	MIL ON run distance	Min.: 0 km (0 mile) Max.: 65535 km (40723 miles)	Actual distance driven since DTC detected	-
Running Time from MIL ON	Running time from MIL on	Min.: 0 min. Max.: 65535 min.	Actual running time since MIL was illuminated	-
Time after DTC Cleared	Time after DTC cleared	Min.: 0 min. Max.: 65535 min.	Actual time elapsed since DTCs were cleared	This is the time elapsed since DTCs were cleared (or after the vehicle left the factory). Time elapsed when the engine switch is turned off is not counted.
Distance from DTC Cleared	Distance driven after DTCs cleared	Min.: 0 km (0 mile) Max.: 65535 km (40723 miles)	Actual distance driven since DTCs cleared	This is the distance driven since DTCs were cleared (or after the vehicle left the factory).
Warmup Cycle Cleared DTC	Warmup cycles after DTCs cleared	Min.: 0 Max.: 255	-	This is the number of times the engine was warmed up*1 after DTCs were cleared (or after the vehicle left the factory).
OBD Requirements	OBD requirement	-	-	-
Number of Emission DTC	Emissions-related DTCs stored	Min.: 0 Max.: 127	-	-
IG ON Duration Time	IG ON duration time	Min.: 0 ms, Max.: 2147483647 ms	-	-
IG OFF Duration Time	IG OFF duration time	Min.: 0 ms, Max.: 2147483647 ms	-	-
Accel Position from EFI	Accelerator pedal position	Min.: 0% Max.: 127.5%	Actual accelerator pedal position	-
NSS Sensor Speed	Secondary pulley speed (NSS)	Min.: 0 rpm Max.: 65535 rpm	0 rpm: Vehicle stopped and shift lever in D Equal to NO Sensor Speed: Vehicle being driven in belt mode	-
NSS Sensor Voltage	Transmission revolution sensor (NSS) output voltage	Min.: 0.000 V Max.: 4.999 V	0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N)	-
NO Sensor Speed	Output shaft speed (NOUT)	Min.: 0 rpm Max.: 65535 rpm	0 rpm: Vehicle stopped Equal to NSS Sensor Speed: Vehicle being driven in belt mode	-
NO Sensor Voltage	Transmission revolution sensor (NOUT) output voltage	Min.: 0.000 V Max.: 4.999 V	0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N)	-
NT Sensor Speed	Input turbine speed (NT)	Min.: 0 rpm Max.: 65535 rpm	Equal to engine speed (NE): Lock-up ON (After warming up engine) Nearly equal to engine speed (NE): Lock-up OFF (Engine idling with shift lever in P or N) 0 rpm: Vehicle stopped with shift lever in R	-
NC1 Sensor Speed	Intermediate shaft (C1 clutch) speed (NC1)	Min.: 0 rpm Max.: 65535 rpm	0 rpm: Vehicle stopped and synchronizer engaged Equal to NT Sensor Speed: Vehicle being driven in gear mode	-
NC1 Sensor Voltage	Transmission revolution sensor (NC1) output voltage	Min.: 0.000 V Max.: 4.999 V	0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N)	-
Belt Clamping Force Sensor	Secondary oil pressure value	Min.: -64 MPa Max.: 63.998 MPa	Secondary oil pressure inspection: 3.5 to 4.3 MPa (35.7 to 43.8 kgf/cm², 508 to 624 psi): D position stall test 1.6 to 2.4 MPa (16.3 to 24.5 kgf/cm², 232 to 348 psi): R position stall test	-
Shift SW Status (P Range)	Park/neutral position switch assembly status	OFF or ON	OFF: Shift lever not in P ON: Shift lever in P	When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. HINT: If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*4.
Shift SW Status (R Range)	Park/neutral position switch assembly status	OFF or ON	OFF: Shift lever not in R ON: Shift lever in R	When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. HINT: If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*4.
Shift SW Status (N Range)	Park/neutral position switch assembly status	OFF or ON	OFF: Shift lever not in N ON: Shift lever in N	When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. HINT: If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*4.
Shift SW Status (N,P Range)	Park/neutral position switch assembly status	ON or OFF	ON: Shift lever in P or N OFF: Shift lever not in P or N	When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. HINT: If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*4.
Shift SW Status (N,P Range) Supported	Status of park/neutral position switch (N or P) supported	Unsupp or Supp	Supp	-
Sport Shift Up SW	Sport shift up switch status	OFF or ON	ON: Shift lever held in "+" or "+" shift paddle switch operated OFF: Shift lever not held in "+" and "+" shift paddle switch released	-
Sport Shift Down SW	Sport shift down switch status	OFF or ON	ON: Shift lever held in "-" or "-" shift paddle switch operated OFF: Shift lever not held in "-" and "-" shift paddle switch released	-
Shift SW Status (S Range)	Transmission control switch status	OFF or ON	ON: Shift lever in M, "+" or "-" OFF: Shift lever not in M, "+" or "-"	-
Shift SW Status (B Range)	Park/neutral position switch status	OFF or ON	OFF: Shift lever not in B ON: Shift lever in B	When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. HINT: If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*4.
Shift SW Status (D Range)	Park/neutral position switch assembly status	OFF or ON	OFF: Shift lever not in D ON: Shift lever in D	When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. HINT: If the same malfunction occurs even after adjusting these parts, refer to DTC P070513*4.
A/T Oil Temperature No.1	CVT fluid temperature sensor value	Min.: -40°C (-40°F) Max.: 150°C (302°F)	Approximately 100°C (212°F): After stall speed test Equal to ambient temperature: After cold soak	If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.
ATF Thermal Degradation Estimate	Estimated value of CVT fluid thermal degradation	Min.: 0 Max.: 65535	-	If 50000 or more is displayed, thermal degradation of the CVT fluid is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the CVT fluid.
CVT Oil Press Calibration	CVT Oil Pressure Calibration status	Incompl or Compl	Compl	-
NT Sensor Voltage	Transmission revolution sensor (NT) output voltage	Min.: 0.000 V Max.: 4.999 V	0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N)	-
Acceleration Sensor Voltage	Converted output voltage of yaw rate and acceleration sensor	Min.: 0.000 V Max.: 79.999 V	2.31 V to 2.69 V: Vehicle on level ground 1.88 V to 2.5 V: Decelerating 2.5 V to 3.11 V: Accelerating 1.87 V: G sensor malfunction 1.87 V: Communication malfunction	-
Synchronize Stroke Sensor Position	Position of synchronizer	Min.: 0.000 mm Max.: 255.996 mm	0.000 to 1.573 mm (0 to 0.062 in.): Synchronizer not engaged 9.139 to 11.798 mm (0.360 to 0.464 in.): Synchronizer engaged	-
Synchronize Stroke Sensor Voltage	Shift stroke sensor voltage	Min.: 0.000 V Max.: 4.999 V	3.587 to 4.429 V: Synchronizer not engaged 0.622 to 1.393 V: Synchronizer engaged	-
Status of Synchronize	Synchronizer status	OFF or ON	OFF: Synchronizer not engaged ON: Synchronizer engaged	-
Lock Up Status	Lock-up	OFF, ON or Invalid Value	ON: Lock-up operating OFF: Lock-up not operating	-
CVT Shift Status Ratio	TCM gear ratio command	Min.: 0 Max.: 15.999	Same as actual gear ratio	-
Shift Mode	Shift mode status	Gear Mode or Belt Mode	-	-
Solenoid (SLU)	Shift solenoid valve SLU status	OFF or ON	ON: Shift solenoid valve SLU operating OFF: Shift solenoid valve SLU not operating	-
Solenoid (SLS) High/Low	Shift solenoid valve SLS status	OFF or ON	ON: After engine start OFF: Engine switch on (IG)	-
Solenoid (SLS) MAX/MIN	Shift solenoid valve SLS status	OFF or ON	ON: After engine start OFF: Engine switch on (IG)	-
Solenoid (SLP)	Shift solenoid valve SLP status	OFF or ON	ON: Shift solenoid valve SLP operating OFF: Shift solenoid valve SLP not operating	-
Solenoid (SLG)	Shift solenoid valve SLG status	OFF or ON	ON: Shift solenoid valve SLG operating OFF: Shift solenoid valve SLG not operating	-
Solenoid (SL1)	Shift solenoid valve SL1 status	OFF or ON	ON: Shift solenoid valve SL1 operating OFF: Shift solenoid valve SL1 not operating	-
Solenoid (SL2)	Shift solenoid valve SL2 status	OFF or ON	ON: Shift solenoid valve SL2 operating OFF: Shift solenoid valve SL2 not operating	-
Acceleration Sensor Calibration	Deceleration sensor zero point calibration status	Incompl or Compl	Complete	-
Acceleration Sensor Learn Value	Yaw rate and acceleration sensor learned value voltage	Min.: 0.000 V Max.: 79.998 V	2.31 to 2.69 V: Deceleration Sensor Zero Point Calibration complete	-

HINT:

*1: An engine warmup is defined as the engine coolant temperature rising 20°C (68°F) or more and reaching a temperature of 70°C (158°F) or more after the engine is started.
*2:
- Avail: The monitor is available on this vehicle.
- Not Avl: The monitor is not available on this vehicle.
- Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at sometime in the past. This item does not change when the engine switch is turned off. However, it will change to Incmpl when DTCs are cleared or the cable is disconnected from the negative (-) battery terminal.
- Monitor result (mode 06): The last judgment result is output. This is not cleared when the engine switch is turned off, but is cleared when DTCs are cleared.
*3:
- Enable: The monitor is available on the vehicle.
- Unable: The monitor is not available on the vehicle.
- Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed during the current trip. The item changes back to Incmpl when the engine switch is turned off.
- Monitor result (mode 06): The last judgment result is output. This is not cleared when the engine switch is turned off, but is cleared when DTCs are cleared. Therefore, only when DTCs are cleared at the beginning of a trip does the system monitor (Test Result [Monitor Status]) and monitor result (mode 06) match.
*4: Refer to DTC P070513.
Click here

(h) Enter the following menus: Powertrain / Engine / Data List.

(i) According to the display on the Techstream, read the Data List.

Powertrain > Engine > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Drive Mode Status	Drive mode status	Normal, Power, Sport, Sport+, Comfort or ECO	-	-
Power Mode SW	SPORT switch (combination switch assembly) status	ON or OFF	ON: SPORT switch (combination switch assembly) being pushed OFF: SPORT switch (combination switch assembly) not being pushed	-
Drive Mode Select Switch (DMS+)	Drive mode select switch (combination switch assembly) status	ON or OFF	ON: Drive mode select switch (combination switch assembly) pushed forward OFF: Drive mode select switch (combination switch assembly) in neutral position	-
Drive Mode Select Switch (DMS-)	Drive mode select switch (combination switch assembly) status	ON or OFF	ON: Drive mode select switch (combination switch assembly) pulled rearward OFF: Drive mode select switch (combination switch assembly) in neutral position	-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Turn the engine switch off.

(d) Turn the engine switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / Transmission / Active Test.

(g) According to the display on the Techstream, perform the Active Test.

Powertrain > Transmission > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Activate the TC Terminal	Turn on and off TC and TE1 (CG) connection	ON or OFF	ON: TC and TE1 are connected. OFF: TC and TE1 are disconnected. (Vehicle Condition) Engine switch on (IG), engine stopped and shift lever in P
Activate the Lock Up Solenoid	Operates the lock-up	ON or OFF	Can be used to check lock-up operation. Perform "Activate the Lock Up Solenoid" while monitoring "Engine Speed" and "NT Sensor Speed". (Vehicle Condition) Vehicle speed: 40 km/h (25 mph) or more
Activate the Solenoid (SLU)	Operates the shift solenoid valve SLU	ON or OFF	(Vehicle Condition) Engine switch on (IG), engine stopped and shift lever in P or N
Activate the Solenoid (SLS) High/Low	Operates the shift solenoid valve SLS	High or Low	(Vehicle Condition) Engine switch on (IG), engine stopped and shift lever in P or N
Activate the Solenoid (SLS) MAX/MIN	Operates the shift solenoid valve SLS	MIN or MAX	(Vehicle Condition) Engine switch on (IG), engine stopped and shift lever in P or N
Activate the Solenoid (SLP)	Operates the shift solenoid valve SLP	ON or OFF	(Vehicle Condition) Engine switch on (IG), engine stopped and shift lever in P or N
Active the Synchronize	Operates the synchronizer	ON or OFF	HINT: If the value of Data List item Status of Synchronize is "ON", this Active Test cannot be changed to "ON". Additionally, if the value is "OFF", this Active Test cannot be changed to "OFF". (Vehicle Condition) Engine switch on (IG), engine running, stop light switch assembly ON, shift lever in P and CVT fluid temperature between 20°C (68°F) and 100°C (212°F)
Control the Shift Mode	Changes the shift mode	GEAR: Gear Mode LOW: Belt Mode (Low) MIDDLE: Belt Mode (Middle) HIGH: Belt Mode (High)	HINT: Perform "Control the Shift Mode" while monitoring "CVT Shift Status Ratio" and "Shift Mode" to confirm actual shift mode. (Vehicle Condition) Vehicle speed between 20 km/h (10.8 mph) and 45 km/h (24.3 mph) and CVT fluid temperature -20°C (-4 °F) or more
Activate the Solenoid (SLG)	Operates the shift solenoid valve SLG	ON or OFF	(Vehicle Condition) Engine switch on (IG), engine stopped and shift lever in P or N
Activate the Solenoid (SL1)	Operates the shift solenoid valve SL1	ON or OFF	(Vehicle Condition) Engine switch on (IG), engine stopped and shift lever in P or N
Activate the Solenoid (SL2)	Operates the shift solenoid valve SL2	ON or OFF	(Vehicle Condition) Engine switch on (IG), engine stopped and shift lever in P or N

DATA LIST / ACTIVE TEST

Powertrain > Transmission > Data List

Powertrain > Engine > Data List

Powertrain > Transmission > Active Test

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)

(Vehicle Condition)