Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM1000000025UNX |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: EA67F / EA68F (MANUAL TRANSMISSION / TRANSAXLE): MANUAL TRANSAXLE SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING; 2023 - 2025 MY Corolla Corolla Hatchback GR Corolla [09/2022 - ] |
HOW TO PROCEED WITH TROUBLESHOOTING
|
CAUTION / NOTICE / HINT
HINT:
-
The ECM of this system is connected to the CAN communication system. Therefore, before starting troubleshooting, be sure to check that there are no malfunctions in the CAN communication system.
-
*: Use the Techstream.
PROCEDURE
1.
|
VEHICLE BROUGHT TO WORKSHOP
|
NEXT
|
|
|
2.
|
CUSTOMER PROBLEM ANALYSIS
|
(a) Refer to How to Troubleshoot ECU Controlled Systems in Introduction.
Click here
NEXT
|
|
|
(a) Check the battery voltage.
Standard Voltage:
11 to 14 V
HINT:
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
NEXT
|
|
|
4.
|
CONNECT TECHSTREAM TO DLC3*
|
HINT:
If the display indicates a communication fault in the Techstream, inspect the DLC3.
When any CAN communication system DTCs are output, perform troubleshooting on the CAN communication system first.
NEXT
|
|
|
5.
|
CHECK CAN COMMUNICATION SYSTEM*
|
(a) Use the Techstream to check if the CAN communication system is functioning normally.
CAN Bus Check
Result
|
Proceed to
|
CAN communication DTCs are not output
|
A
|
CAN communication DTCs are output
|
B
|
A
|
|
|
6.
|
CHECK AND CLEAR DTCS AND FREEZE FRAME DATA*
|
(a) Check for DTCs.
Click here
Powertrain > Engine > Trouble Codes
(b) Check for freeze frame data.
Click here
HINT:
Record or print DTCs and freeze frame data if necessary.
(c) Clear for DTCs.
Click here
Powertrain > Engine > Clear DTCs
NEXT
|
|
|
7.
|
PROBLEM SYMPTOM CONFIRMATION
|
(a) Refer to Road Test.
Click here
Result
|
Proceed to
|
Symptom does not occur
|
A
|
Symptom occurs
|
B
|
A
|
|
|
(a) Refer to Symptom Simulation.
Click here
NEXT
|
|
|
(a) Check for DTCs.
Powertrain > Engine > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTCs are output
|
B
|
A
|
|
|
10.
|
PROBLEM SYMPTOMS TABLE
|
(a) Refer to Problem Symptoms Table.
Click here
Result
|
Proceed to
|
Fault is not listed in problem symptoms table
|
A
|
Fault is listed in problem symptoms table
|
B
|
A
|
|
|
11.
|
OVERALL ANALYSIS AND TROUBLESHOOTING*
|
(a) Data List / Active Test
Click here
(b) Terminals of ECM
Click here
NEXT
|
|
|
12.
|
REPAIR OR REPLACEMENT
|
NEXT
|
|
|
(a) Refer to the road test section to perform a road test.
NEXT |
|
END
|
14.
|
DIAGNOSTIC TROUBLE CODE CHART
|
(a) Proceed to Diagnostic Trouble Code Chart.
Click here
NEXT
|
|
|
NEXT
|
|
|
16.
|
IDENTIFICATION OF PROBLEM
|
|