Q810 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL; 2023 MY Corolla Corolla HV [09/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000025SQK
Model Year Start: 2023	Model: Corolla	Prod Date Range: [09/2022 - 11/2022]
Title: Q810 (HYBRID TRANSMISSION / TRANSAXLE): REAR TRACTION MOTOR: REMOVAL; 2023 MY Corolla Corolla HV [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear traction motor with transaxle assembly removal/installation are shown below.

Necessary Procedures after parts removed/installed/replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
Replacement of rear traction motor with transaxle assembly	Resolver learning Initialize resolver	DTCs are stored Slight vibration at a vehicle speed of 5 km/h (3 mph) or less Shock or vibration during acceleration
Rear wheel alignment adjustment	Perform "Reset Memory" Perform "Calibration"	DTCs are stored ABS warning light illuminates Brake system warning light (yellow indicator) illuminates Slip indicator light illuminates Electronically controlled brake system disabled or malfunctions
Gas leak from exhaust system is repaired	Inspection after repair	Poor idle, etc. Engine start function, etc.

CAUTION:

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click here
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
Front Camera System (for TMC Made)	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

PROCEDURE

1. PERFORM RESOLVER INITIALIZATION

NOTICE:

If it is necessary to replace the rear traction motor with transaxle assembly, make sure to perform resolver initialization before starting work.

Click here

2. REMOVE SERVICE PLUG GRIP

Click here

3. REMOVE CONNECTOR COVER ASSEMBLY

Click here

4. CHECK TERMINAL VOLTAGE

Click here

5. INSTALL CONNECTOR COVER ASSEMBLY

Click here

6. REMOVE SPARE WHEEL COVER

Click here

7. REMOVE SPARE WHEEL CUSHION

(a) Remove the spare wheel cushion.

8. REMOVE MOTOR CONNECTOR PROTECTOR

(a) Remove the 3 nuts and motor connector protector from the vehicle body.

9. DISCONNECT REAR TRACTION MOTOR CABLE

(a) Disengage the 2 clamps to disconnect the rear traction motor cable from the vehicle body.

(b) Remove the 2 nuts to disconnect the radio earth bracket from the vehicle body.

HINT:

Release the lock before rotating the lock lever.

(d) Separate the grommet of the rear traction motor cable from the vehicle body and push out the rear traction motor cable from the cabin.

10. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

Click here

11. REMOVE NO. 6 FLOOR WIRE

(a) Disconnect the motor temperature sensor connector.

*a	Motor Temperature Sensor Connector
*b	Motor Resolver Sensor Connector

(b) Disconnect the motor resolver sensor connector.

12. DISCONNECT REAR TRACTION MOTOR CABLE

(a) Disengage the 2 clamps to disconnect the rear traction motor cable.

13. REMOVE REAR TRACTION MOTOR WITH TRANSAXLE ASSEMBLY

(a) Using a mini crane and 2 belt slings, hold the rear traction motor with transaxle assembly.

CAUTION:

Do not lift the rear traction motor with transaxle assembly more than necessary.
When lifting the rear traction motor with transaxle assembly, make sure it is well balanced.

NOTICE:

Lightly shake the rear traction motor with transaxle assembly by hand to make sure it is securely held while performing work.
Do not shake the rear traction motor with transaxle assembly excessively while holding it.

(b) Remove the 4 bolts, 2 upper differential mount stoppers, 2 lower differential mount stoppers, differential mass damper and rear traction motor with transaxle assembly from the rear suspension member sub-assembly.

*1	Upper Differential Mount Stopper	*2	Front Differential Support Assembly
*3	Lower Differential Mount Stopper	*4	Rear Suspension Member Sub-assembly
*5	Differential Mass Damper	-	-

NOTICE:

Be careful not to drop the rear traction motor with transaxle assembly.
Be careful not to damage the installation surfaces of the rear traction motor with transaxle assembly when removing it.

14. REMOVE FRONT DIFFERENTIAL SUPPORT ASSEMBLY

(a) Remove the 2 bolts and front differential support assembly from the rear traction motor with transaxle assembly.

15. REMOVE REAR TRACTION MOTOR CABLE

Click here

16. REMOVE MOTOR CABLE BRACKET

(a) Remove the 3 bolts and 3 motor cable brackets from the rear traction motor with transaxle assembly.

17. REMOVE WIRE HARNESS CLAMP BRACKET

(a) Remove the bolt and wire harness clamp bracket from the rear traction motor with transaxle assembly.

18. REMOVE DIFFERENTIAL DYNAMIC DAMPER

HINT:

Perform this procedure only when replacement of the differential dynamic damper is necessary.

The illustration shown is an example only. The illustration may differ from the actual parts according to the model.

*A	for Type A	*B	for Type B
*C	for Type C	-	-

(a) Remove the bolts and differential dynamic dampers from the front differential support assembly.

REMOVAL

CAUTION / NOTICE / HINT

Necessary Procedures after parts removed/installed/replaced

Learning completes when vehicle is driven

PROCEDURE

for Type A:

for Type B:

for Type C: