- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
- Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000025Q6G |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: INTERIOR PANELS / TRIM: ROOF HEADLINING (for Sedan): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining assembly removal/installation are shown below.
CAUTION:
Be sure to read Precaution thoroughly before servicing.
for TMC Made: Click here
![2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): PRECAUTION](/t3Portal/stylegraphics/info.gif)
for TMMMS Made: Click here
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for GR Model *2: except GR Model
Front Camera System (for TMC Made)
Pre-collision System (for TMMMS Made)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Hatchback Power Door Lock Control System
- Back door opener*1
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
Click here
2. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
Click here
3. REMOVE REAR SEAT ASSEMBLY
Click here
4. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Click here
6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
7. REMOVE FRONT PILLAR GARNISH LH
Click here
8. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)
Click here
9. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)
(a) Disengage the claw as shown in the illustration.
|
Place Hand Here |
|
Remove in this Direction |
(b) Disengage the 6 claws and 3 guides to remove the rear door scuff plate LH as shown in the illustration.
|
|
Remove in this Direction |
10. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
11. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)
Click here
12. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
13. REMOVE CENTER PILLAR LOWER GARNISH LH
Click here
14. REMOVE CENTER PILLAR UPPER GARNISH LH
Click here
15. REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
16. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
18. REMOVE FRONT PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
19. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
20. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
21. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)
HINT:
Use the same procedure as for the LH side.
22. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
23. REMOVE CENTER PILLAR LOWER GARNISH RH
HINT:
Use the same procedure as for the LH side.
24. REMOVE CENTER PILLAR UPPER GARNISH RH
HINT:
Use the same procedure as for the LH side.
25. REMOVE REAR UNDER SIDE COVER LH (for HV Model)
(a) Remove the 2 clips.
|
|
Remove in this Direction |
(b) Disengage the claw, 4 clips and guide to remove the rear under side cover LH as shown in the illustration.
26. REMOVE REAR SEAT SIDE GARNISH LH (w/o Rear Seat Side Airbag)
|
(a) Disengage the clip, 2 claws and 2 guides. |
|
(b) Pass the rear seatback hinge sub-assembly LH through the rear seat side garnish LH as shown in the illustration and remove the rear seat side garnish LH.
|
*1 |
Rear Seatback Hinge Sub-assembly LH |
|
|
Remove in this Direction |
27. REMOVE REAR SEAT SIDE GARNISH LH (w/ Rear Seat Side Airbag)
|
(a) Disengage the 8 claws and 4 guides. |
|
(b) Pass the rear seatback hinge sub-assembly LH through the rear seat side garnish LH as shown in the illustration and remove the rear seat side garnish LH.
|
*1 |
Rear Seatback Hinge Sub-assembly LH |
|
|
Remove in this Direction |
28. REMOVE ROOF SIDE INNER GARNISH LH
(a) Disengage the 3 clips as shown in the illustration.
|
|
Place Hand Here |
|
|
Remove in this Direction |
(b) Disengage the 2 guides to remove the roof side inner garnish LH as shown in the illustration.
|
|
Remove in this Direction |
29. REMOVE REAR UNDER SIDE COVER RH (for HV Model)
HINT:
Use the same procedure as for the LH side.
30. REMOVE REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
31. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
32. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
33. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for Manual Transaxle)
for EA67F / EA68F: Click here
for EG60: Click here
for EC65: Click here
34. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for CVT)
for K313: Click here
for K120: Click here
35. REMOVE MAP LIGHT ASSEMBLY
for TMC Made:
for TMMMS Made:
36. REMOVE NO. 1 ROOM LIGHT ASSEMBLY
for Bulb Type:
for LED Type:
37. REMOVE VANITY LIGHT ASSEMBLY (w/ Vanity Light)
for Bulb Type:
for LED Type:
38. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover)
Click here
39. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)
for TMC Made:
for TMMMS Made:
40. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)
for TMC Made:
for TMMMS Made:
41. REMOVE ASSIST GRIP SUB-ASSEMBLY
Click here
42. REMOVE REAR ASSIST GRIP ASSEMBLY LH
HINT:
Use the same procedure as for the assist grip sub-assembly.
43. REMOVE REAR ASSIST GRIP ASSEMBLY RH
HINT:
Use the same procedure as for the assist grip sub-assembly.
44. REMOVE VISOR ASSEMBLY LH
Click here
45. REMOVE VISOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
46. REMOVE ROOF HEADLINING ASSEMBLY
(a) for Windshield Glass Side with Connector:
(1) Disconnect each connector.
(b) for Front Pillar LH Side:
(1) Remove the protective cover.
|
(2) Using a clip remover, disengage the 4 clamps. |
|
(3) Disconnect the 2 connectors.
(4) Install the protective cover.
(c) for Front Pillar RH Side:
(1) Remove the protective cover.
|
(2) Using a clip remover, disengage the 3 clamps. |
|
(3) Disconnect each connector.
(4) Install the protective cover.
(d) for Rear Pillar RH Side:
|
(1) Disconnect the 2 connectors. |
|
(2) Disengage the clamp.
(e) Turn the visor holder approximately 45° and remove it as indicated by the arrows, in the order shown in the illustration.
|
*a |
45° |
|
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
HINT:
Use the same procedure for the LH side and RH side.
(f) for Roof Side (for Normal Roof):
(1) Disengage the 2 claws to remove the base of each visor holder.
|
*a |
Base of Visor Holder |
- |
- |
(2) Using a clip remover, remove the 3 clips.
(g) for Roof Side (for Moon Roof):
(1) Disconnect the connector.
|
*a |
Base of Visor Holder |
- |
- |
(2) Disengage the 2 claws to remove the base of each visor holder.
(3) Using a clip remover, remove the 3 clips.
(4) Disengage the 6 fasteners.
(h) Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.
|
|
Remove in this Direction |
- |
- |
NOTICE:
Do not damage the roof headlining assembly or vehicle interior.
|
|