2ZR-FXE (EMISSION CONTROL): EGR VALVE: REMOVAL; 2023 MY Corolla Corolla HV [09/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM1000000025P13
Model Year Start: 2023	Model: Corolla	Prod Date Range: [09/2022 - 11/2022]
Title: 2ZR-FXE (EMISSION CONTROL): EGR VALVE: REMOVAL; 2023 MY Corolla Corolla HV [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
Replacement of inverter with converter assembly	ECU configuration	-
Replacement of inverter with converter assembly	Resolver learning	DTCs are stored Slight vibration at a vehicle speed of 5 km/h (3 mph) or less Shock or vibration during acceleration
Replacement of ECM	Vehicle Identification Number (VIN) or frame number registration	MIL comes on
	ECU configuration	-
	Update ECU security key	Vehicle Control History (RoB) are stored
Replacement of EGR valve assembly Gas leak from exhaust system is repaired	Inspection after repair	Poor idle, etc. Engine start function, etc.

CAUTION:

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click here
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.
Be sure to wear insulating gloves when working on high voltage wiring or components.
If work is performed without wearing insulating gloves, there is a danger of electric shock.

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly recordsvarious types of memory and settings. As a result, after turning the ignition switch off,make sure to wait at least 3 minutes before disconnecting the cable from the negative(-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and thesecurity lock setting has been enabled, multi-display operations will be disabled uponnext startup unless the password is entered. Be sure to check the security lock settingbefore disconnecting the cable from the negative (-) auxiliary battery terminal. (forAudio and Visual System (for Single Knob Type))

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
Front Camera System (for TMC Made)	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. DRAIN ENGINE COOLANT (for Engine)

Click here

3. REMOVE INVERTER WITH CONVERTER ASSEMBLY

Click here

4. REMOVE EGR PIPE ASSEMBLY

Click here

5. REMOVE EGR VALVE ASSEMBLY

(a) Disconnect the EGR valve assembly connector.

(b) Slide the clip and disconnect the No. 6 water by-pass hose from the EGR valve assembly.

(d) Remove the 3 nuts.

(e) Using an E8 "TORX" socket wrench, remove the stud bolt from the camshaft housing sub-assembly.

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.

(f) Remove the EGR valve assembly from the EGR pipe with cooler sub-assembly.

(g) Remove the EGR valve gasket from the EGR valve assembly.