Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM1000000025OKB
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: EXTERIOR PANELS / TRIM: FRONT BUMPER (for Sedan without Illumination): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

for TMC Made:

HINT:

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

for Target Adjustment (Triangle Target):

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: MILLIMETER WAVE RADAR SENSOR (for TMC Made): TARGET ADJUSTMENT(TRIANGLE TARGET)

for Target Adjustment (Flat Surface Target):

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: MILLIMETER WAVE RADAR SENSOR (for TMC Made): TARGET ADJUSTMENT(FLAT SURFACE TARGET)

for Driving Adjustment:

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: MILLIMETER WAVE RADAR SENSOR (for TMC Made): DRIVING ADJUSTMENT

for TMMMS Made:

HINT:

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: MILLIMETER WAVE RADAR SENSOR (for TMMMS Made): ADJUSTMENT

PROCEDURE

1. REMOVE RADIATOR SUPPORT OPENING COVER (for Gasoline Model)

(a) for TMMMS Made:

(1) Remove the 8 clips.

(2) Disengage the guide as shown in the illustration to remove the radiator support opening cover.

Remove in this Direction (1)

Remove in this Direction (2)

(b) for TMC Made:

(1) Disengage the 7 clips to remove the radiator support opening cover.

2. REMOVE RADIATOR SUPPORT OPENING COVER (for HV Model)

(a) Disengage the 6 clips to remove the radiator support opening cover.

3. REMOVE FRONT BUMPER ASSEMBLY

(a) Apply protective tape around the front bumper assembly as shown in the illustration.

Protective Tape

(b) As shown in the illustration, pull the front bumper assembly horizontally to release each claw and disengage the front fender liner retainer.

Remove in this Direction (1)

Remove in this Direction (2)

HINT:

Use the same procedure for the RH side and LH side.

(c) Remove the clip.

HINT:

Use the same procedure for the RH side and LH side.

(d) Remove the 10 screws.

(e) Disengage the 4 claws as shown in the illustration.

Place Hand Here

Remove in this Direction

HINT:

Use the same procedure for the RH side and LH side.

(f) Disconnect the connector.

*A

w/o Pre-collision System

*B

w/ Pre-collision System

(g) Remove the bolt and 2 screws.

(h) Disengage the claw of the front bumper assembly as shown in the illustration.

*a

Press location

-

-

NOTICE:

If the front bumper assembly is moved in the direction forward of the vehicle, the claw may be damaged.

HINT:

Use the same procedure for the RH side and LH side.

(1) Pull the end portion of the front bumper assembly away from the vehicle.

(2) While pressing the location shown in the illustration, move the end portion of the front bumper assembly in the direction indicated by the arrow.

(3) Using your hand, strike the location shown in the illustration to disengage the claw.

*a

Location to strike with hand

-

-

NOTICE:

Be careful not to damage the front bumper assembly when striking it with your hand.

(i) Disengage the 3 claws as shown in the illustration to remove the front bumper assembly.

Remove in this Direction