Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000025JBV
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): Engine Oil Pressure Switch Circuit; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

Engine Oil Pressure Switch Circuit

DESCRIPTION

The combination meter assembly and engine oil pressure switch assembly are connected via direct line. The combination meter assembly determines the engine oil pressure based on the engine oil pressure switch signal.

HINT:

  • The combination meter assembly receives various signals in order to output warnings from the ECM and hybrid vehicle control ECU via CAN communication.
  • The combination meter assembly operates the following to output oil pressure warnings:
    1. Engine oil pressure warning buzzer
    2. Engine oil pressure warning message on multi-information display

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
  • The following troubleshooting procedure is based on the assumption that the SFI system and hybrid control system are normal. Confirm that the SFI system and hybrid control system are not malfunctioning before performing the following procedure.

    SFI system (for 2ZR-FXE): Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

    SFI system (for 2ZR-FAE): Click here 2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

    Hybrid control system: Click here 2023 - 2025 MY Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with PA10): HOW TO PROCEED WITH TROUBLESHOOTING

  • for TMC Made

    When replacing the combination meter assembly, update the ECU security key.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: UPDATE ECU SECURITY KEY

PROCEDURE

1.

INSPECT ENGINE OIL PRESSURE SWITCH ASSEMBLY

for 2ZR-FXE: Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; 2ZR-FXE (LUBRICATION): OIL PRESSURE SWITCH: INSPECTION

for 2ZR-FAE: Click here 2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (LUBRICATION): OIL PRESSURE SWITCH: INSPECTION

NG

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY

for 2ZR-FXE: Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; 2ZR-FXE (LUBRICATION): OIL PRESSURE SWITCH: REMOVAL

for 2ZR-FAE: Click here 2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (LUBRICATION): OIL PRESSURE SWITCH: REMOVAL

OK

2.

CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the I5 combination meter assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

C39-1 - I5-9 (S)*1

C39-1 - I5-23 (S)*2

Always

Below 1 Ω

C39-1 or I5-9 (S) - Body ground*1

C39-1 or I5-23 (S) - Body ground*2

Always

10 kΩ or higher
  • *1: for TMC Made
  • *2: for TMMC Made
OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR