Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000025DVJ
Model Year Start: 2023 Model: Corolla Prod Date Range: [09/2022 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): VSC OFF Switch Circuit; 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]

VSC OFF Switch Circuit

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRAC operation, and pressing and holding this switch turns off TRAC and VSC operation. If TRAC and VSC operations are turned off, "Traction Control Turned Off" will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

PROCEDURE

1.

READ VALUE USING GTS (TRAC/VSC OFF MODE)

(a) Operate the GTS to read the Data List.

Chassis > Brake/EPB > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

TRC(TRAC)/VSC OFF Mode

TRAC/VSC off mode

Normal mode (TRC(TRAC) ON/VSC ON) /

TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) /

VSC expert mode (VSC expert mode MID ON) /

VSC OFF mode (TRC(TRAC) OFF/VSC OFF)

Normal mode (TRC(TRAC) ON/VSC ON): Normal mode

TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRAC off mode

VSC expert mode (VSC expert mode MID ON): VSC expert mode

VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode

-

Chassis > Brake/EPB > Data List

Tester Display

TRC(TRAC)/VSC OFF Mode

(b) Check the indicator light and mode condition on the GTS changes according to VSC OFF switch operation.

Standard:

Switch Operation

Mode Condition Display

Multi-information Display ("Traction Control Turned Off")

VSC OFF Indicator Light

Not pressed

Normal mode (TRC(TRAC) ON/VSC ON)

Not displayed

Does not come on

Pressing the VSC OFF switch

TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON)

Displayed

Does not come on

Pressing and holding the VSC OFF switch

VSC OFF mode (TRC(TRAC) OFF/VSC OFF)

Displayed

Comes on

Result

Proceed to

Indicator light and mode condition display do not change (VSC OFF switch (for Instrument Panel))

A

Indicator light and mode condition display do not change (VSC OFF switch (for Shift Panel))

B

Mode condition display is normal, but indicator light does not change

C

Indicator light and mode condition display are normal

D

B

GO TO STEP 4

C

INSPECT METER / GAUGE SYSTEM 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): HOW TO PROCEED WITH TROUBLESHOOTING 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): HOW TO PROCEED WITH TROUBLESHOOTING

D

USE SIMULATION METHOD TO CHECK

A

2.

INSPECT VSC OFF SWITCH

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VSC OFF SWITCH: INSPECTION

OK:

The VSC OFF switch is normal.

NG

REPLACE VSC OFF SWITCH 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VSC OFF SWITCH: REMOVAL 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VSC OFF SWITCH: REMOVAL

OK

3.

CHECK HARNESS AND CONNECTOR (VSC OFF SWITCH - BRAKE ACTUATOR ASSEMBLY)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

(b) Disconnect the A51 skid control ECU (brake actuator assembly) connector.

(c) Disconnect the I45 VSC OFF switch connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I45-5 (+) - A51-38 (CSW)

Always

Below 1 Ω

I45-5 (+) or A51-38 (CSW) - Body ground

Always

10 kΩ or higher

I45-2 (E) - Body ground

1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal

Below 1 Ω

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.

INSPECT COMBINATION SWITCH ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VSC OFF SWITCH: INSPECTION

OK:

The VSC OFF switch (combination switch assembly) is normal.

NG

REPLACE COMBINATION SWITCH ASSEMBLY 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VSC OFF SWITCH: REMOVAL 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VSC OFF SWITCH: REMOVAL

OK

5.

CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION SWITCH ASSEMBLY)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.

(b) Disconnect the A51 skid control ECU (brake actuator assembly) connector.

(c) Disconnect the I61 VSC OFF switch (combination switch assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I61-7 (+) - A51-38 (CSW)

Always

Below 1 Ω

I61-7 (+) or A51-38 (CSW) - Body ground

Always

10 kΩ or higher

I61-5 (E) - Body ground

1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal

Below 1 Ω

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR