- Sensor installation
- Yaw rate sensor (airbag sensor assembly)
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000025DVA |
| Model Year Start: 2023 | Model: Corolla | Prod Date Range: [09/2022 - ] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): Zero Point Calibration of Yaw Rate Sensor Undone (X204C); 2023 - 2025 MY Corolla Corolla HV [09/2022 - ] | ||
|
Zero Point Calibration of Yaw Rate Sensor Undone (X204C) |
DESCRIPTION
The airbag sensor assembly has a built-in yaw rate and acceleration sensor.
|
Code |
Tester Display |
Measurement Item |
Trouble Area |
Output ECU |
|---|---|---|---|---|
|
X204C |
Zero Point Calibration of Yaw Rate Sensor Undone |
History of incomplete yaw rate sensor zero point calibration |
|
Skid control ECU (brake actuator assembly) |
PROCEDURE
|
1. |
CHECK DTC (HEALTH CHECK) |
(a) Perform the Health Check using the GTS.
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTCs are output |
B |
| B |
|
GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
|
2. |
CLEAR ZERO POINT VALUE FOR YAW RATE AND ACCELERATION SENSOR |
(a) Clear the zero point value for the yaw rate and acceleration sensor.
Click here
![2023 - 2025 MY Corolla Corolla HV [09/2022 - ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): UTILITY](/t3Portal/stylegraphics/info.gif)
Chassis > Brake/EPB > Utility
|
Tester Display |
|---|
|
Reset Memory |
|
|
3. |
PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR |
(a) Perform zero point calibration of the yaw rate and acceleration sensor.
Click here
Chassis > Brake/EPB > Utility
|
Tester Display |
|---|
|
Calibration |
|
|
4. |
CLEAR VEHICLE CONTROL HISTORY (RoB) |
(a) Using the GTS, clear the Vehicle Control History (RoB).
Chassis > Brake/EPB > Utility
|
Tester Display |
|---|
|
Vehicle Control History (RoB) |
|
|
5. |
CHECK VEHICLE CONTROL HISTORY (RoB) |
(a) Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
(b) Using the GTS, check for Vehicle Control History (RoB).
Chassis > Brake/EPB > Utility
|
Tester Display |
|---|
|
Vehicle Control History (RoB) |
|
Result |
Proceed to |
|---|---|
|
X204C is not output |
A |
|
X204C is output |
B |
| A |
|
END |
|
|
6. |
CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION |
(a) Turn the ignition switch off.
(b) Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click here
OK:
The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.
The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.
| NG |
|
INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY
|
|
|
7. |
READ VALUE USING GTS (LATERAL G, FORWARD AND REARWARD G AND YAW RATE SENSOR VALUE) |
(a) Check the yaw rate and acceleration sensor output value displayed on the GTS.
Chassis > Brake/EPB > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Lateral G |
Lateral G |
Min.: -25.105 m/s2, Max.: 24.908 m/s2 |
Turning right: -25.105 to 0.000 m/s2 Turning left: 0.000 to 24.908 m/s2 |
During turning: Changes in proportion with lateral acceleration |
|
Forward and Rearward G |
Forward and rearward G |
Min.: -25.105 m/s2, Max.: 24.908 m/s2 |
During deceleration: -25.105 to 0.000 m/s2 During acceleration: 0.000 to 24.908 m/s2 |
During acceleration/deceleration: Changes in proportion with acceleration |
|
Yaw Rate Sensor Value |
Yaw rate sensor |
Min.: -128°/s, Max.: 127°/s |
Vehicle stopped: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
Chassis > Brake/EPB > Data List
|
Tester Display |
|---|
|
Lateral G |
|
Forward and Rearward G |
|
Yaw Rate Sensor Value |
OK:
The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.
| OK |
|
| NG |
|
REPLACE AIRBAG SENSOR ASSEMBLY
|
|
|