Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000025DTQ |
Model Year Start: 2023 |
Model: Corolla |
Prod Date Range: [09/2022 -
] |
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model): C05202A,C11782A; Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range; 2023 - 2025 MY Corolla Corolla HV [09/2022 - ] |
DTC
|
C05202A
|
Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range
|
DTC
|
C11782A
|
Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range
|
DESCRIPTION
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
The skid control ECU (brake actuator assembly) memorizes the range of the acceleration sensor (airbag sensor assembly) and the range of vehicle speed calculated using each speed sensor.
This DTC is stored when the acceleration sensor (airbag sensor assembly) value is abnormal when the vehicle is accelerating or decelerating.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
DTC Output from
|
Note
|
C05202A
|
Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range
|
From the time the vehicle starts off until it stops, the longitudinal acceleration sensor value fluctuates 0.5 m/s2 or less during acceleration/deceleration between 1.47 m/s2 and 12 m/s2 , or the value always remains 36% or less of vehicle acceleration for 1 to 2 seconds.*
|
Acceleration sensor (airbag sensor assembly)
|
Comes on
|
Brake/EPB
|
-
SAE Code: C051C (Case 3)
-
Output ECU: Skid control ECU (brake actuator assembly)
-
for AWD
|
C11782A
|
Multi-axis Acceleration Sensor Module "A" Signal Stuck In Range
|
From the time the vehicle starts off until it stops, the longitudinal acceleration sensor value fluctuates 0.5 m/s2 or less during acceleration/deceleration between 1.47 m/s2 and 12 m/s2 , or the value always remains 36% or less of vehicle acceleration for 1 to 2 seconds.*
|
Acceleration sensor (airbag sensor assembly)
|
Does not come on
|
Brake/EPB
|
-
Output ECU: Skid control ECU (brake actuator assembly)
-
for 2WD
|
-
*: Varies depending on the vehicle driving conditions.
MONITOR DESCRIPTION
When CAN communication of the yaw rate and acceleration sensor (airbag sensor assembly) is valid, the vehicle is being driven within a certain range of acceleration and deceleration, and the longitudinal acceleration sensor (airbag sensor assembly) signal is a certain value or less for a certain amount of time, the skid control ECU (brake actuator assembly) illuminates the MIL and stores this DTC.
MONITOR STRATEGY
Related DTCs
|
C051C (Case 3): Longitudinal acceleration sensor constant signal monitoring
|
Required Sensors/Components(Main)
|
Skid control ECU (brake actuator assembly)
Acceleration sensor (airbag sensor assembly)
|
Required Sensors/Components(Related)
|
Skid control ECU (brake actuator assembly)
Acceleration sensor (airbag sensor assembly)
|
Frequency of Operation
|
Continuous
|
Duration
|
1 to 2 seconds (depending on driving situation)
|
MIL Operation
|
2 driving cycles
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
TMC's intellectual property
|
Other conditions belong to TMC's intellectual property
|
-
|
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property
|
-
|
COMPONENT OPERATING RANGE
TMC's intellectual property
|
-
|
CONFIRMATION DRIVING PATTERN
NOTICE:
When performing the normal judgment procedure, make sure that the driver door is closed and is not opened at any time during the procedure.
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
-
Connect the GTS to the DLC3.
-
Turn the ignition switch to ON and turn the GTS on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off.
-
Turn the ignition switch to ON (READY) and turn the GTS on.
-
Drive the vehicle at a speed of 1 km/h (1 mph) or more for 1 second or more. [*]
HINT:
[*]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
-
Enter the following menus: Chassis / Brake/EPB* / Utility / All Readiness.
*: Electric Parking Brake System
-
Check the DTC judgment result.
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result shows INCOMPLETE, perform driving pattern again.
PROCEDURE
1.
|
REPLACE AIRBAG SENSOR ASSEMBLY
|
(a) Replace the yaw rate and acceleration sensor (airbag sensor assembly).
Click here
NEXT |
|
END
|
|