| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000025DLW |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: LIGHTING (EXT): LIGHTING SYSTEM (for TMC Made): LO-beam Headlight does not Illuminate; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
|
LO-beam Headlight does not Illuminate |
DESCRIPTION
The main body ECU (multiplex network body ECU) controls the low beam headlights.
WIRING DIAGRAM
for LED Type Turn Signal Light (for G16E-GTS)
for LED Type Turn Signal Light (for M20A-FKS, 2ZR-FXE)
for Bulb Type Turn Signal Light
CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
-
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
for HV Model:Click here
![2023 - 2025 MY Corolla Corolla HV [09/2022 - ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): REGISTRATION](/t3Portal/stylegraphics/info.gif)
for Gasoline Model:Click here
-
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CXPI communication malfunctions before troubleshooting this symptom.
Click here
PROCEDURE
|
1. |
CONFIRM MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
for LED Type Turn Signal Light |
A |
|
for Bulb Type Turn Signal Light |
B |
| B |
|
|
|
2. |
PERFORM ACTIVE TEST USING GTS |
(a) Perform the Active Test according to the display on the GTS.
Body Electrical > Main Body > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Headlight Relay / Light Power Supply Relay |
Low beam headlights |
OFF or ON |
- |
Body Electrical > Main Body > Active Test
|
Tester Display |
|---|
|
Headlight Relay / Light Power Supply Relay |
OK:
Low beam headlights illuminate.
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (LH side low beam headlight does not illuminate) |
B |
|
NG (RH side low beam headlight does not illuminate) |
C |
| A |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| B |
|
| C |
|
|
3. |
PERFORM ACTIVE TEST USING GTS |
(a) Perform the Active Test according to the display on the GTS.
Body Electrical > Main Body > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Headlight Relay / Light Power Supply Relay |
Low beam headlights |
OFF or ON |
- |
Body Electrical > Main Body > Active Test
|
Tester Display |
|---|
|
Headlight Relay / Light Power Supply Relay |
OK:
Low beam headlights illuminate.
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (for LH Side) |
B |
|
NG (for RH Side) |
C |
| A |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| C |
|
|
|
4. |
INSPECT HEADLIGHT UNIT ASSEMBLY LH (LO TERMINAL VOLTAGE) |
(a) Disconnect the A130 headlight unit assembly LH connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A130-2 (LO) - Body ground |
Light control switch in head position |
11 to 14 V |
| NG |
|
|
|
5. |
CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT ASSEMBLY LH - BODY GROUND) |
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A130-5 (E) - Body ground |
Always |
Below 1 Ω |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
6. |
CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT UNIT ASSEMBLY LH) |
(a) Remove the H-LP LH relay.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (H-LP LH relay) - A130-2 (LO) |
Always |
Below 1 Ω |
|
3 (H-LP LH relay) or A130-2 (LO) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
7. |
INSPECT H-LP LH RELAY |
|
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG |
|
REPLACE H-LP LH RELAY |
|
|
8. |
CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY) |
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
2 (H-LP LH relay) - Body ground |
Always |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - POWER DISTRIBUTION BOX ASSEMBLY) |
(a) Disconnect the 8F power distribution box assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
1 (H-LP LH relay) - 8F-3 |
Always |
Below 1 Ω |
|
1 (H-LP LH relay) or 8F-3 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
10. |
INSPECT POWER DISTRIBUTION BOX ASSEMBLY |
(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
8F-3 - MB-8 (HRLY) |
Always |
Below 1 Ω |
| OK |
|
| NG |
|
|
11. |
INSPECT HEADLIGHT UNIT ASSEMBLY RH (LO TERMINAL VOLTAGE) |
(a) Disconnect the A129 headlight unit assembly RH connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A129-2 (LO) - Body ground |
Light control switch in head position |
11 to 14 V |
| NG |
|
|
|
12. |
CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT ASSEMBLY RH - BODY GROUND) |
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A129-5 (E) - Body ground |
Always |
Below 1 Ω |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
13. |
CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT UNIT ASSEMBLY RH) |
(a) Remove the H-LP RH relay.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (H-LP RH relay) - A129-2 (LO) |
Always |
Below 1 Ω |
|
3 (H-LP RH relay) or A129-2 (LO) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
14. |
INSPECT H-LP RH RELAY |
|
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG |
|
REPLACE H-LP RH RELAY |
|
|
15. |
CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY) |
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
2 (H-LP RH relay) - Body ground |
Always |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
16. |
CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - POWER DISTRIBUTION BOX ASSEMBLY) |
(a) Disconnect the 8F power distribution box assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
1 (H-LP RH relay) - 8F-4 |
Always |
Below 1 Ω |
|
1 (H-LP RH relay) or 8F-4 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
17. |
INSPECT POWER DISTRIBUTION BOX ASSEMBLY |
(a) Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
8F-4 - MB-9 (HRY2) |
Always |
Below 1 Ω |
| OK |
|
| NG |
|
|
|