Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000259XB |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): B005211; Passenger Seat Belt Sensor Circuit Short to Ground; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] |
DTC
|
B005211
|
Passenger Seat Belt Sensor Circuit Short to Ground
|
DESCRIPTION
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Warning Indicate
|
DTC Output from
|
Priority
|
Test Mode / Check Mode
|
B005211
|
Passenger Seat Belt Sensor Circuit Short to Ground
|
One of the following conditions is met:
-
The airbag sensor assembly detects a short circuit to ground signal in the passenger seat belt sensor circuit for 2 seconds.
-
Passenger seat buckle switch malfunction.
-
Airbag sensor assembly malfunction.
|
-
Harness or connector
-
Passenger seat buckle switch (Front seat inner belt assembly RH)
-
Airbag sensor assembly
|
Comes on
|
SRS Airbag
|
A
|
Does not apply to test/check mode
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
PROCEDURE
1.
|
CHECK CONNECTION OF CONNECTORS
|
Pre-procedure1
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
Procedure1
(c) Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly RH.
OK:
The connectors are properly connected.
Post-procedure1
(d) None
NG |
|
CONNECT CONNECTORS PROPERLY
|
OK
|
|
|
Pre-procedure1
(a) Disconnect the airbag sensor assembly connector.
|
|
*1
|
Front Seat Inner Belt Assembly RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
|
|
(b) Disconnect the front seat inner belt assembly RH connector.
Procedure1
(c) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
Post-procedure1
(d) None
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN THE CIRCUIT)
|
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
j5-1 (+) - j5-2 (-)
|
Always
|
1 MΩ or higher
|
|
|
*1
|
Front Seat Inner Belt Assembly RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
*a
|
Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)
|
|
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)
|
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
j5-1 (+) - Body ground
|
Always
|
1 MΩ or higher
|
j5-2 (-) - Body ground
|
Always
|
1 MΩ or higher
|
|
|
*1
|
Front Seat Inner Belt Assembly RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
*a
|
Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)
|
|
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
Pre-procedure1
(a) Connect the airbag sensor assembly connector.
|
|
*1
|
Front Seat Inner Belt Assembly RH
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
|
|
(b) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
(c) Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
(d) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs
Post-procedure1
(e) Turn the ignition switch off.
NEXT
|
|
|
Pre-procedure1
(a) Turn the ignition switch to ON, and wait for at least 60 seconds.
Procedure1
(b) Check for DTCs.
Body Electrical > SRS Airbag > Trouble Codes
Result
|
Proceed to
|
B005211 is output
|
A
|
B005211 is not output
|
B
|
HINT:
Codes other than DTC B005211 may be output at this time, but they are not related to this check.
Post-procedure1
(c) None
|