Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM10000000259X1
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): OPERATION CHECK; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

OPERATION CHECK

PRECAUTION FOR OPERATION CHECK

CAUTION:

Use the correct procedure to replace the airbag parts.

CHECK SRS WARNING LIGHT

(a) Primary check

(1) Turn the ignition switch to ON and check that the SRS warning light turns on.

(2) Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system (including the seat belt pretensioners) is performed.

NOTICE:

Turn the ignition switch off when the auxiliary battery is connected.

HINT:

  • If the SRS warning light remains on for approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a malfunction with the airbag system.
  • If the warning light occasionally turns on approximately 6 seconds or more after the ignition switch has been turned to ON, there may be a short to +B, short to ground or an open in the SRS warning light circuit.
  • If the warning light illuminates after turning the ignition switch off or to ACC, there may be a malfunction in the power source circuit or combination meter assembly.
  • The SRS warning light turns off, and then turns on. This blinking pattern indicates a source voltage drop. The SRS warning light turns off 6 to 10 seconds after the source voltage returns to normal.

FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR

(a) Initial check

(1) Turn the ignition switch to ON.

(2) The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.

(3) Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the following conditions.

Indicator Operation

Front Passenger Seat Condition

Passenger Airbag ON/OFF Indicator

SRS Warning Light

ON Indicator

OFF Indicator

Vacant

OFF

ON

OFF

Adult*1 is seated

ON

OFF

OFF

Child*2 is seated

ON or OFF*2

OFF or ON*2

OFF

Child restraint system is installed

OFF

ON

OFF

Occupant classification system failure

OFF

ON

ON
  • *1: The system judges a person of average adult weight or more as an adult. If a smaller adult sits in the front passenger seat, the system may not recognize them as an adult depending on their physique and posture.
  • *2: The system may not recognize a child or a child in a child restraint system as a child depending on factors such as the positioning of the child restraint system or the child's physique or posture.

HINT:

  • The timing chart below shows the operation of the passenger airbag ON/OFF indicator. Use the chart to check the indicator light circuit.
  • When the occupant classification system has trouble, both the SRS warning light and passenger airbag ON/OFF indicator ("OFF") come on. In this case, check for DTCs for "Airbag System" first.

INSPECT AIRBAG COMPONENTS

(a) Inspect the SRS parts in table below.

Component to Inspect

Procedure

Horn button assembly
  1. Perform a diagnostic system check.
  2. Visually check for defects with the horn button assembly installed to the vehicle.

    HINT:

    The defects are as follows:

    • Cuts on the surface or in the grooves
    • Small cracks on the surface or in the grooves
    • Significant discoloration on the surface or in the grooves

    OK:

    No defects are found.

    If any defects are found, replace the horn button assembly with a new one.

Lower No. 1 instrument panel airbag assembly
  1. Perform a diagnostic system check.
  2. Visually check for defects with the lower No. 1 instrument panel airbag assembly installed to the vehicle.

    HINT:

    The defects are as follows:

    • Cuts
    • Small cracks
    • Significant discoloration

    OK:

    No defects are found.

    If any defects are found, replace the lower No. 1 instrument panel airbag assembly with a new one.

Instrument panel passenger airbag assembly
  1. Perform a diagnostic system check.
  2. Visually check for defects with the instrument panel passenger airbag assembly installed to the vehicle.

    HINT:

    The defects are as follows:

    • Cuts on the instrument panel safety pad sub-assembly around the instrument panel passenger airbag assembly
    • Small cracks on the instrument panel safety pad sub-assembly around the instrument panel passenger airbag assembly
    • Significant discoloration on the instrument panel safety pad sub-assembly around the instrument panel passenger airbag assembly

    OK:

    No defects are found.

    If any defects are found, replace the instrument panel safety pad sub-assembly with a new one.

Curtain shield airbag assembly
  1. Perform a diagnostic system check.
  2. Visually check for defects with the curtain shield airbag assemblies installed to the vehicle.

    HINT:

    The defects are as follows:

    • Cuts on each pillar garnish or the roof headlining assembly around the curtain shield airbag assemblies
    • Small cracks on each pillar garnish or the roof headlining assembly around the curtain shield airbag assemblies
    • Significant discoloration on each pillar garnish or the roof headlining assembly around the curtain shield airbag assemblies

    OK:

    No defects are found.

    If any defects are found, replace each pillar garnish or the roof headlining assembly with a new one.

Front seat airbag assembly
  1. Perform a diagnostic system check.
  2. Visually check for defects with the front seat airbag assemblies installed to the vehicle.

    HINT:

    The defects are as follows:

    • Scratches, broken or frayed threads on the surface of the separate type front seatback assembly around the front seat airbag assemblies
    • Small cracks on the separate type front seatback assembly around the front seat airbag assemblies
    • Significant discoloration on the separate type front seatback assembly around the front seat airbag assemblies

    OK:

    No defects are found.

    If any defects are found, replace the separate type front seatback pad or separate type front seatback cover with a new one.

Rear seat airbag assembly
  1. Perform a diagnostic system check.
  2. Visually check for defects with the rear seat airbag assemblies installed to the vehicle.

    HINT:

    The defects are as follows:

    • Cuts
    • Small cracks
    • Significant discoloration

    OK:

    No defects are found.

    If any defects are found, replace the rear seat airbag assembly with a new one.

Front seat cushion airbag assembly RH
  1. Perform a diagnostic system check.
  2. Visually check for defects with the front seat cushion airbag assembly RH installed to the vehicle.

    HINT:

    The defects are as follows:

    • Scratches, broken or frayed threads on the surface of the front seat cushion assembly around the front seat cushion airbag assembly RH
    • Small cracks on the front seat cushion assembly around the front seat cushion airbag assembly RH
    • Significant discoloration on the front seat cushion assembly around the front seat cushion airbag assembly RH

    OK:

    No defects are found.

    If any defects are found, replace the separate type front seat cushion pad or separate type front seat cushion cover with a new one.

Front seat outer belt assembly
  1. Perform a diagnostic system check.
  2. Visually check for defects with the front seat outer belt assemblies installed to the vehicle.

    HINT:

    The defects are as follows:

    • Cuts
    • Small cracks
    • Significant discoloration

    OK:

    No defects are found.

    If any defects are found, replace the front seat outer belt assembly with a new one.

Rear 3 point type seat outer belt assembly
  1. Perform a diagnostic system check.
  2. Visually check for defects with the rear 3 point type seat outer belt assemblies installed to the vehicle.

    HINT:

    The defects are as follows:

    • Cuts
    • Small cracks
    • Significant discoloration

    OK:

    No defects are found.

    If any defects are found, replace the rear 3 point type seat outer belt assembly with a new one.

Airbag sensor assembly
  1. Check for DTCs and freeze frame data.

Front airbag sensor

Side airbag pressure sensor

Side No. 1 airbag sensor

Harness and connector