Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM10000000259WN
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): B00D212; Restraint System Malfunction Indicator 1 Circuit Short to Battery; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

DTC

B00D212

Restraint System Malfunction Indicator 1 Circuit Short to Battery

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

DTC Output from

Priority

Test Mode / Check Mode

B00D212

Restraint System Malfunction Indicator 1 Circuit Short to Battery

  • The airbag sensor assembly detects a short circuit +B signal in the passenger airbag ON/OFF indicator "ON" circuit when the airbag sensor assembly sends an "ON" request signal to the "ON" indicator in the passenger airbag ON/OFF indicator.
  • Passenger airbag ON/OFF indicator malfunction
  • Airbag sensor assembly malfunction
  • Harness or connector
  • Passenger airbag ON/OFF indicator (map light assembly)
  • Airbag sensor assembly

Comes on

SRS Airbag

A

Does not apply to test/check mode

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: AUTOMATIC LEARNING CHART

  • After replacing the airbag sensor assembly, refer to work procedure.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE

PROCEDURE

1.

CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag sensor assembly and map light assembly.

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK

2.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag sensor assembly connector.

*1

Map Light Assembly

*2

Airbag Sensor Assembly

*3

Wire Harness

(b) Disconnect the map light assembly connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

I47-35 (PAON) or T6-20 (PAON) - Body ground

Ignition switch ON

Below 1 V

Result:

Proceed to

OK

NG

*1

Map Light Assembly

*2

Airbag Sensor Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Map Light Assembly)

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

Post-procedure1

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK PASSENGER AIRBAG ON/OFF INDICATOR

Pre-procedure1

(a) Connect the map light assembly connector.

*1

Map Light Assembly

*2

Airbag Sensor Assembly

*3

Wire Harness

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

(b) Using a service wire, connect terminal 35 (PAON) of connector B and body ground.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON.

Procedure1

(e) Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator "ON" come on.

Post-procedure1

(f) Turn the ignition switch off.

(g) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

(h) Disconnect the service wire from connector B.

OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY