Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000259WJ
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): B00B500; Driver Seat Track Position Restraints Sensor Circuit Undetermined Failure; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

DTC

B00B500

Driver Seat Track Position Restraints Sensor Circuit Undetermined Failure

DESCRIPTION

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

DTC Output from

Priority

Test Mode / Check Mode

B00B500

Driver Seat Track Position Restraints Sensor Circuit Undetermined Failure

When it is determined that the specified number of times or more is not achieved after the ignition switch is turned to ON.

  • Harness or connector
  • Seat position sensor (front seat adjuster assembly LH)*
  • Front seat inner belt assembly LH
  • Airbag sensor assembly

Comes on

SRS Airbag

A

Does not apply to test/check mode

  • *: The seat position sensor is built into the front seat adjuster assembly LH.

WIRING DIAGRAM

for Manual Seat:
for Power Seat:

CAUTION / NOTICE / HINT

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: AUTOMATIC LEARNING CHART

  • After replacing the airbag sensor assembly, refer to work procedure.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE

PROCEDURE

1.

CHECK VEHICLE CONDITION

(a) Choose the model to be inspected.

Result

Proceed to

for Manual Seat

A

for Power Seat

B

B

GO TO STEP 19

A

2.

CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag sensor assembly and seat position sensor (front seat adjuster assembly LH).

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK

3.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag sensor assembly connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

(b) Disconnect the seat position sensor connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH OR REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

INSPECT SEAT POSITION SENSOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

Pre-procedure1

(a) Remove the seat position sensor (front seat adjuster assembly LH).

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): REMOVAL

Procedure1

(b) Inspect the seat position sensor.

(1) Remove and reinsert the metal plate under the bottom face of the seat position sensor and measure the current value.

*1

Seat Position Sensor

*2

Auxiliary battery

*a

Component without harness connected

(Seat Position Sensor (Front Seat Adjuster Assembly LH))

*b

Tester

*c

Metal plate

*d

Bottom Face

Standard Current:

Tester Connection

Condition

Specified Condition

Tester positive (+) - 1

Tester negative (-) - Auxiliary battery negative (-)

Metal plate inserted

4.7 to 7.3 mA

Metal plate not inserted

11.4 to 17.9 mA

Post-procedure1

(c) None

NG

REPLACE SEAT POSITION SENSOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

OK

5.

CHECK SEAT POSITION SENSOR CIRCUIT (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

(a) Using a service wire, connect terminals 27 (LSP+) and 24 (GNDL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*5

Service Wire

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

z20-1 (GND) - z20-2 (VS)

Always

Below 1 Ω

Post-procedure1

(c) Disconnect the service wire from connector B.

NG

GO TO STEP 16

OK

6.

CHECK SEAT POSITION SENSOR CIRCUIT (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

z20-1 (GND) - Body ground

Always

1 MΩ or higher

z20-2 (VS) - Body ground

Always

1 MΩ or higher

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

NG

GO TO STEP 13

OK

7.

CHECK SEAT POSITION SENSOR CIRCUIT (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

z20-1 (GND) - Body ground

Ignition switch ON

Below 1 V

z20-2 (VS) - Body ground

Ignition switch ON

Below 1 V

Result:

Proceed to

OK

NG

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

Post-procedure1

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

NG

GO TO STEP 10

OK

8.

CLEAR DTC

Pre-procedure1

(a) Connect the airbag sensor assembly connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

(b) Connect the seat position sensor (front seat adjuster assembly LH) connector.

(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

Procedure1

(e) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

Post-procedure1

(f) Turn the ignition switch off.

NEXT

9.

CHECK DTC

Pre-procedure1

(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

Procedure1

(b) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to

B00B500 is output

A

B00B500 is not output

B

HINT:

Codes other than DTC B00B500 may be output at this time, but they are not related to this check.

Post-procedure1

(c) None

A

REPLACE AIRBAG SENSOR ASSEMBLY

B

USE SIMULATION METHOD TO CHECK

10.

CHECK CONNECTION OF CONNECTORS

(a) Check that the connectors are properly connected to the front seat inner belt assembly LH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

11.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the front seat inner belt assembly LH connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

Procedure1

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(c) None

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH OR REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

12.

CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - AIRBAG SENSOR ASSEMBLY)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

O23-4 (LSP+) - Body ground

Ignition switch ON

Below 1 V

O23-3 (LSP-) - Body ground

Ignition switch ON

Below 1 V

Result:

Proceed to

OK

NG

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Front Seat Inner Belt Assembly LH)

Post-procedure1

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.

CHECK CONNECTION OF CONNECTORS

(a) Check that the connectors are properly connected to the front seat inner belt assembly LH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

14.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the front seat inner belt assembly LH connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

Procedure1

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(c) None

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH OR REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

15.

CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - AIRBAG SENSOR ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O23-4 (LSP+) - Body ground

Always

1 MΩ or higher

O23-3 (LSP-) - Body ground

Always

1 MΩ or higher

Result:

Proceed to

OK

NG

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Front Seat Inner Belt Assembly LH)

OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.

CHECK CONNECTION OF CONNECTORS

(a) Check that the connectors are properly connected to the front seat inner belt assembly LH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

17.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the front seat inner belt assembly LH connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

Procedure1

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(c) None

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH OR REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

18.

CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - AIRBAG SENSOR ASSEMBLY)

Pre-procedure1

(a) Using a service wire, connect terminals 27 (LSP+) and 24 (GNDL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O23-4 (LSP+) - O23-3 (LSP-)

Always

Below 1 Ω

Result:

Proceed to

OK

NG

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*5

Service Wire

*a

Front view of wire harness connector

(to Front Seat Inner Belt Assembly LH)

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

Post-procedure1

(c) Disconnect the service wire from connector B.

OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.

CHECK CONNECTION OF CONNECTORS

Pre-procedure1

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

Procedure1

(c) Check that the connectors are properly connected to the airbag sensor assembly and seat position sensor (front seat adjuster assembly LH).

OK:

The connectors are properly connected.

Post-procedure1

(d) None

NG

CONNECT CONNECTORS PROPERLY

OK

20.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the airbag sensor assembly connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

(b) Disconnect the seat position sensor connector.

Procedure1

(c) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(d) None

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

21.

INSPECT SEAT POSITION SENSOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

Pre-procedure1

(a) Remove the seat position sensor (front seat adjuster assembly LH).

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SEAT: FRONT SEAT ASSEMBLY (for Power Seat): REMOVAL

Procedure1

(b) Inspect the seat position sensor.

(1) Remove and reinsert the metal plate under the bottom face of the seat position sensor and measure the current value.

*1

Seat Position Sensor

*2

Auxiliary battery

*a

Component without harness connected

(Seat Position Sensor (Front Seat Adjuster Assembly LH))

*b

Tester

*c

Metal plate

*d

Bottom Face

Standard Current:

Tester Connection

Condition

Specified Condition

Tester positive (+) - 1

Tester negative (-) - Auxiliary battery negative (-)

Metal plate inserted

4.7 to 7.3 mA

Metal plate not inserted

11.4 to 17.9 mA

Post-procedure1

(c) None

NG

REPLACE SEAT POSITION SENSOR (FRONT SEAT ADJUSTER ASSEMBLY LH)

OK

22.

CHECK SEAT POSITION SENSOR CIRCUIT (CHECK FOR OPEN IN THE CIRCUIT)

Pre-procedure1

(a) Using a service wire, connect terminals 27 (LSP+) and 24 (GNDL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*5

Service Wire

-

-

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

q10-1 (GND) - q10-2 (VS)

Always

Below 1 Ω

Post-procedure1

(c) Disconnect the service wire from connector B.

NG

GO TO STEP 35

OK

23.

CHECK SEAT POSITION SENSOR CIRCUIT (CHECK FOR SHORT TO GROUND IN THE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

q10-1 (GND) - Body ground

Always

1 MΩ or higher

q10-2 (VS) - Body ground

Always

1 MΩ or higher

NG

GO TO STEP 31

OK

24.

CHECK SEAT POSITION SENSOR CIRCUIT (CHECK FOR SHORT TO +B IN THE CIRCUIT)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

-

-

Standard Voltage:

Tester Connection

Condition

Specified Condition

q10-1 (GND) - Body ground

Ignition switch ON

Below 1 V

q10-2 (VS) - Body ground

Ignition switch ON

Below 1 V

Post-procedure1

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

NG

GO TO STEP 27

OK

25.

CLEAR DTC

Pre-procedure1

(a) Connect the airbag sensor assembly connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

(b) Connect the seat position sensor (front seat adjuster assembly LH) connector.

(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

Procedure1

(e) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

Post-procedure1

(f) Turn the ignition switch off.

NEXT

26.

CHECK DTC

Pre-procedure1

(a) Turn the ignition switch to ON, and wait for at least 60 seconds.

Procedure1

(b) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

Result

Proceed to

B00B500 is output

A

B00B500 is not output

B

HINT:

Codes other than DTC B00B500 may be output at this time, but they are not related to this check.

Post-procedure1

(c) None

A

REPLACE AIRBAG SENSOR ASSEMBLY

B

USE SIMULATION METHOD TO CHECK

27.

CHECK CONNECTION OF CONNECTORS

(a) Check that the connectors are properly connected to the front seat inner belt assembly LH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

28.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the front seat inner belt assembly LH connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

Procedure1

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(c) None

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH OR REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

29.

CHECK HARNESS AND CONNECTOR (SEAT POSITION SENSOR - FRONT SEAT INNER BELT ASSEMBLY LH)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

-

-

Standard Voltage:

Tester Connection

Condition

Specified Condition

q10-2 (VS) - Body ground

Ignition switch ON

Below 1 V

q10-1 (GND) - Body ground

Ignition switch ON

Below 1 V

Post-procedure1

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

30.

CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - AIRBAG SENSOR ASSEMBLY)

Pre-procedure1

(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.

(b) Turn the ignition switch to ON.

Procedure1

(c) Measure the voltage according to the value(s) in the table below.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Front Seat Inner Belt Assembly LH)

-

-

Standard Voltage:

Tester Connection

Condition

Specified Condition

O23-4 (LSP+) - Body ground

Ignition switch ON

Below 1 V

O23-3 (LSP-) - Body ground

Ignition switch ON

Below 1 V

Post-procedure1

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.

OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.

CHECK CONNECTION OF CONNECTORS

(a) Check that the connectors are properly connected to the front seat inner belt assembly LH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

32.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the front seat inner belt assembly LH connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

Procedure1

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(c) None

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH OR REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

33.

CHECK HARNESS AND CONNECTOR (SEAT POSITION SENSOR - FRONT SEAT INNER BELT ASSEMBLY LH)

(a) Measure the resistance according to the value(s) in the table below.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

q10-2 (VS) - Body ground

Always

1 MΩ or higher

q10-1 (GND) - Body ground

Always

1 MΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

34.

CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - AIRBAG SENSOR ASSEMBLY)

(a) Measure the resistance according to the value(s) in the table below.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*a

Front view of wire harness connector

(to Front Seat Inner Belt Assembly LH)

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

O23-4 (LSP+) - Body ground

Always

1 MΩ or higher

O23-3 (LSP-) - Body ground

Always

1 MΩ or higher

OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.

CHECK CONNECTION OF CONNECTORS

(a) Check that the connectors are properly connected to the front seat inner belt assembly LH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

36.

CHECK CONNECTORS

Pre-procedure1

(a) Disconnect the front seat inner belt assembly LH connector.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

Procedure1

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

Post-procedure1

(c) None

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH OR REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

37.

CHECK HARNESS AND CONNECTOR (SEAT POSITION SENSOR - FRONT SEAT INNER BELT ASSEMBLY LH)

Pre-procedure1

(a) Using a service wire, connect terminals 2 (LSP+) and 1 (LSP-) of connector F.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*5

Service Wire

-

-

*a

Front view of wire harness connector

(to Seat Position Sensor (Front Seat Adjuster Assembly LH))

*b

Front view of wire harness connector

(to Front Seat Inner Belt Assembly LH)

Standard Resistance:

Tester Connection

Condition

Specified Condition

q10-2 (VS) - q10-1 (GND)

Always

Below 1 Ω

Post-procedure1

(c) Disconnect the service wire from connector F.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

38.

CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - AIRBAG SENSOR ASSEMBLY)

Pre-procedure1

(a) Using a service wire, connect terminals 27 (LSP+) and 24 (GNDL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

Procedure1

(b) Measure the resistance according to the value(s) in the table below.

*1

Seat Position Sensor (Front Seat Adjuster Assembly LH)

*2

Front Seat Inner Belt Assembly LH

*3

Airbag Sensor Assembly

*4

Wire Harness

*5

Service Wire

-

-

*a

Front view of wire harness connector

(to Front Seat Inner Belt Assembly LH)

*b

Front view of wire harness connector

(to Airbag Sensor Assembly)

Standard Resistance:

Tester Connection

Condition

Specified Condition

O23-4 (LSP+) - O23-3 (LSP-)

Always

Below 1 Ω

Post-procedure1

(c) Disconnect the service wire from connector B.

OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR