Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000259U2 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): SRS Warning Light Remains ON; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] |
SRS Warning Light Remains ON
|
DESCRIPTION
The SRS warning light is located in the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.
When the auxiliary battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.
A malfunction in this circuit is not recorded in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
HINT:
When the SRS warning light is illuminated due to a drop in supply power voltage, check the vehicle control history (RoB) before performing an inspection as the airbag sensor assembly stores vehicle control history (RoB) (X210B).
Click here
PROCEDURE
1.
|
CHECK SRS WARNING LIGHT OPERATION
|
(a) Turn the ignition switch to ON and check the SRS warning light condition.
HINT:
The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.
Result
|
Proceed to
|
After the primary check period, the SRS warning light remains on.
|
A
|
After the primary check period, the SRS warning light goes off and comes on again.
|
B
|
A
|
|
|
2.
|
CHECK AUXILIARY BATTERY
|
(a) Measure the auxiliary battery voltage with the ignition switch off.
Standard Voltage:
11 to 14 V
NG |
|
REPLACE OR RECHARGE AUXILIARY BATTERY
|
OK
|
|
|
3.
|
CHECK CONNECTION OF CONNECTOR
|
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
(c) Check that the connector is properly connected to the airbag sensor assembly.
OK:
The connector is properly connected.
NG |
|
CONNECT CONNECTOR PROPERLY
|
OK
|
|
|
(a) Disconnect the airbag sensor assembly connector.
|
|
*1
|
Combination Meter Assembly
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
|
|
(b) Check that the terminals of the connector are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
5.
|
CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
|
(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
|
|
*a
|
Front view of wire harness connector
(to Airbag Sensor Assembly)
|
|
|
(b) Turn the ignition switch to ON.
(c) Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
I47-36 (IGR) - Body ground
|
Ignition switch ON
|
8 to 16 V
|
(e) Turn the ignition switch off.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I47-33 (E1) - Body ground
|
Always
|
Below 1 Ω
|
I47-32 (E2) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
6.
|
CHECK SRS WARNING LIGHT
|
(a) Turn the ignition switch to ON.
|
|
*1
|
Combination Meter Assembly
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
|
|
(b) Approximately 6 seconds after the ignition switch is turned to ON, check the condition of the SRS warning light.
Result
|
Proceed to
|
Turns off for 10 seconds, and then illuminates
|
A
|
Turns off for 10 seconds, and then remains off
|
B
|
7.
|
CHECK CAN COMMUNICATION SYSTEM
|
(a) Check if a CAN communication DTC is output.
for HV Model: Click here
for Gasoline Model: Click here
Result
|
Proceed to
|
DTC is not output
|
A
|
DTCs are output
|
B
|
B |
|
GO TO CAN COMMUNICATION SYSTEM
for HV Model: Click here
for Gasoline Model: Click here
|
A
|
|
|
8.
|
CHECK AUXILIARY BATTERY
|
(a) Measure the auxiliary battery voltage with the ignition switch off.
Standard Voltage:
11 to 14 V
NG |
|
REPLACE OR RECHARGE AUXILIARY BATTERY
|
OK
|
|
|
9.
|
CHECK CONNECTION OF CONNECTORS
|
(a) Turn the ignition switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
(c) Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.
OK:
The connectors are properly connected.
NG |
|
CONNECT CONNECTORS PROPERLY
|
OK
|
|
|
(a) Disconnect the airbag sensor assembly connector.
|
|
*1
|
Combination Meter Assembly
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
|
|
(b) Disconnect the combination meter assembly connector.
(c) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
11.
|
CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
|
(a) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
|
|
*a
|
Front view of wire harness connector
(to Airbag Sensor Assembly)
|
|
|
(b) Turn the ignition switch to ON.
(c) Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
I47-36 (IGR) - Body ground
|
Ignition switch ON
|
8 to 16 V
|
(e) Turn the ignition switch off.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I47-33 (E1) - Body ground
|
Always
|
Below 1 Ω
|
I47-32 (E2) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
12.
|
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)
|
(a) Turn the ignition switch to ON.
|
|
*a
|
Front view of wire harness connector
(to Combination Meter Assembly)
|
|
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
I4-6 (IG+) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
(c) Turn the ignition switch off.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I4-1 (EP) - Body ground
|
Always
|
Below 1 Ω
|
I4-2 (ES) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
13.
|
CHECK SRS WARNING LIGHT
|
(a) Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.
|
|
*1
|
Combination Meter Assembly
|
*2
|
Airbag Sensor Assembly
|
*3
|
Wire Harness
|
|
|
(b) Connect the combination meter assembly connector.
(c) Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.
(d) Turn the ignition switch to ON.
(e) Approximately 6 seconds after the ignition switch is turned to ON, check the condition of the SRS warning light.
Result
|
Proceed to
|
Turns off for 10 seconds, and then illuminates
|
A
|
Turns off for 10 seconds, and then remains off
|
B
|
|