Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000257A9
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): B150013; Fuel Sender Circuit Open; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

DTC

B150013

Fuel Sender Circuit Open

DESCRIPTION

  • The fuel sender gauge assembly is connected to the combination meter assembly via direct line. If there is an open or short in the direct line, the combination meter assembly stores DTC B150013.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B150013

Fuel Sender Circuit Open

Diagnosis Condition:

  • Ignition switch ON
  • IG power source voltage is 9.5 V or more

Malfunction Status:

  • Voltage signal from fuel sender gauge assembly is 0.2 V or less
  • Voltage signal from fuel sender gauge assembly is 4.7 V or more

Malfunction Time:

  • 10 seconds or more
  • Fuel suction tube with pump and gauge assembly
  • Fuel sender gauge assembly
  • Harness or connector
  • Combination meter assembly

Combination Meter

A

WIRING DIAGRAM

for TMC Made
for TMMMS Made

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
  • for TMC Made

    When replacing the combination meter assembly, update the ECU security key.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: UPDATE ECU SECURITY KEY

PROCEDURE

1.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for TMC Made

A

for TMMMS Made

B

B

GO TO STEP 11

A

2.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for HV Model

A

for Gasoline Model

B

B

GO TO STEP 7

A

3.

READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Fuel Input

Fuel level gauge output

Min.: 0.00 L, Max.: 655.35 L or Unset

for 4WD

  • Fuel receiver gauge indicates F: 35.58 L
  • Fuel receiver gauge indicates 3/4: 27.78 L
  • Fuel receiver gauge indicates 1/2: 19.99 L
  • Fuel receiver gauge indicates 1/4: 12.19 L
  • Fuel receiver gauge indicates E: 4.39 L

except 4WD

  • Fuel receiver gauge indicates F: 37.82 L
  • Fuel receiver gauge indicates 3/4: 29.43 L
  • Fuel receiver gauge indicates 1/2: 21.04 L
  • Fuel receiver gauge indicates 1/4: 12.64 L
  • Fuel receiver gauge indicates E: 4.25 L

-

Body Electrical > Combination Meter > Data List

Tester Display

Fuel Input

Result

Proceed to

Fuel level data can be displayed on the GTS

A

Fuel level data cannot be displayed on the GTS

B

A

REPLACE COMBINATION METER ASSEMBLY

B

4.

INSPECT FUEL SENDER GAUGE ASSEMBLY

w/ Canister Pump Module: Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; 2ZR-FXE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module): INSPECTION

w/o Canister Pump Module: Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; 2ZR-FXE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module): INSPECTION

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

w/ Canister Pump Module: Click here 2023 MY Corolla Corolla HV [09/2022 - 11/2022]; 2ZR-FXE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module): REMOVAL

w/o Canister Pump Module: Click here 2023 MY Corolla Corolla HV [09/2022 - 11/2022]; 2ZR-FXE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module): REMOVAL

OK

5.

INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O46-1 (FV) - A-3

Always

Below 1 Ω

O46-2 (FE) - A-2

Always

Below 1 Ω

O46-3 (FR) - A-1

Always

Below 1 Ω

O46-1 (FV) - O46-2 (FE)

or

A-3 - A-2

Always

10 kΩ or higher

O46-1 (FV) - O46-3 (FR)

or

A-3 - A-1

Always

10 kΩ or higher

O46-2 (FE) - O46-3 (FR)

or

A-2 - A-1

Always

10 kΩ or higher

*a

Component without harness connected

(Fuel Suction Tube with Pump and Gauge Assembly)

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

w/ Canister Pump Module: Click here 2023 MY Corolla Corolla HV [09/2022 - 11/2022]; 2ZR-FXE (FUEL): FUEL PUMP (w/ Canister Pump Module): REMOVAL

w/o Canister Pump Module: Click here 2023 MY Corolla Corolla HV [09/2022 - 11/2022]; 2ZR-FXE (FUEL): FUEL PUMP (w/o Canister Pump Module): REMOVAL

OK

6.

CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the I5 combination meter assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O46-3 (FR) - I5-7 (FR)

Always

Below 1 Ω

O46-2 (FE) - I5-25 (FE&B)

Always

Below 1 Ω

O46-1 (FV) - I5-23 (FV)

Always

Below 1 Ω

O46-3 (FR) or I5-7 (FR) - Body ground

Always

10 kΩ or higher

O46-1 (FV) or I5-23 (FV) - Body ground

Always

10 kΩ or higher

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.

READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Fuel Input

Fuel level gauge output

Min.: 0.00 L, Max.: 655.35 L or Unset

for 50liter Tank Model

  • Fuel receiver gauge indicates F: 44.50 L
  • Fuel receiver gauge indicates 3/4: 34.63 L
  • Fuel receiver gauge indicates 1/2: 24.75 L
  • Fuel receiver gauge indicates 1/4: 14.88 L
  • Fuel receiver gauge indicates E: 5.00 L

for 47liter Tank Model

  • Fuel receiver gauge indicates F: 41.86 L
  • Fuel receiver gauge indicates 3/4: 32.57 L
  • Fuel receiver gauge indicates 1/2: 23.28 L
  • Fuel receiver gauge indicates 1/4: 13.99 L
  • Fuel receiver gauge indicates E: 4.70 L

-

Body Electrical > Combination Meter > Data List

Tester Display

Fuel Input

Result

Proceed to

Fuel level data can be displayed on the GTS

A

Fuel level data cannot be displayed on the GTS

B

A

REPLACE COMBINATION METER ASSEMBLY

B

8.

INSPECT FUEL SENDER GAUGE ASSEMBLY

w/o Canister Pump Module (for Double Wishbone Type Suspension): Click here 2022 - 2025 MY Corolla Corolla Hatchback [06/2021 -        ]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module (for Double Wishbone Type Suspension)): INSPECTION

w/ Canister Pump Module (for Double Wishbone Type Suspension): Click here 2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module (for Double Wishbone Type Suspension)): INSPECTION

for Torsion Beam Type Suspension: Click here 2023 - 2025 MY Corolla Corolla Hatchback [09/2022 -        ]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module (for Torsion Beam Type Suspension)): INSPECTION

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

w/o Canister Pump Module (for Double Wishbone Type Suspension): Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

w/ Canister Pump Module (for Double Wishbone Type Suspension): Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

for Torsion Beam Type Suspension: Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module (for Torsion Beam Type Suspension)): REMOVAL

OK

9.

INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O46-1 (FV) - A-3

Always

Below 1 Ω

O46-2 (FE) - A-2

Always

Below 1 Ω

O46-3 (FR) - A-1

Always

Below 1 Ω

O46-1 (FV) - O46-2 (FE)

or

A-3 - A-2

Always

10 kΩ or higher

O46-1 (FV) - O46-3 (FR)

or

A-3 - A-1

Always

10 kΩ or higher

O46-2 (FE) - O46-3 (FR)

or

A-2 - A-1

Always

10 kΩ or higher

*a

Component without harness connected

(Fuel Suction Tube with Pump and Gauge Assembly)

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

w/o Canister Pump Module (for Double Wishbone Type Suspension): Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL PUMP (w/o Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

w/ Canister Pump Module (for Double Wishbone Type Suspension): Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL PUMP (w/ Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

for Torsion Beam Type Suspension: Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL PUMP (w/ Canister Pump Module (for Torsion Beam Type Suspension)): REMOVAL

OK

10.

CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the I5 combination meter assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O46-3 (FR) - I5-7 (FR)

Always

Below 1 Ω

O46-2 (FE) - I5-25 (FE&B)

Always

Below 1 Ω

O46-1 (FV) - I5-23 (FV)

Always

Below 1 Ω

O46-3 (FR) or I5-7 (FR) - Body ground

Always

10 kΩ or higher

O46-1 (FV) or I5-23 (FV) - Body ground

Always

10 kΩ or higher

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.

READ VALUE USING GTS

(a) Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Fuel Input

Fuel level gauge output

Min.: 0.00 L, Max.: 655.35 L or Unset

for M20A-FKS

  • Fuel receiver gauge indicates F: 45.00 L
  • Fuel receiver gauge indicates 3/4: 35.00 L
  • Fuel receiver gauge indicates 1/2: 25.00 L
  • Fuel receiver gauge indicates 1/4: 15.00 L
  • Fuel receiver gauge indicates E: 5.00 L

for 2ZR-FAE (w/ Canister Pump Module)

  • Fuel receiver gauge indicates F: 45.00 L
  • Fuel receiver gauge indicates 3/4: 35.00 L
  • Fuel receiver gauge indicates 1/2: 25.00 L
  • Fuel receiver gauge indicates 1/4: 15.00 L
  • Fuel receiver gauge indicates E: 5.00 L

for 2ZR-FAE (w/o Canister Pump Module)

  • Fuel receiver gauge indicates F: 44.85 L
  • Fuel receiver gauge indicates 3/4: 34.99 L
  • Fuel receiver gauge indicates 1/2: 25.00 L
  • Fuel receiver gauge indicates 1/4: 15.00 L
  • Fuel receiver gauge indicates E: 5.00 L

-

Body Electrical > Combination Meter > Data List

Tester Display

Fuel Input

Result

Proceed to

Fuel level data can be displayed on the GTS

A

Fuel level data cannot be displayed on the GTS

B

A

REPLACE COMBINATION METER ASSEMBLY

B

12.

INSPECT FUEL SENDER GAUGE ASSEMBLY

for 2ZR-FAE (w/ Canister Pump Module): Click here 2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module): INSPECTION

for 2ZR-FAE (w/o Canister Pump Module): Click here 2020 - 2023 MY Corolla [03/2019 - 11/2022]; 2ZR-FAE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module): INSPECTION

for M20A-FKS (w/ Canister Pump Module): Click here 2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module (for Double Wishbone Type Suspension)): INSPECTION

for M20A-FKS (w/o Canister Pump Module): Click here 2022 - 2025 MY Corolla Corolla Hatchback [06/2021 -        ]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module (for Double Wishbone Type Suspension)): INSPECTION

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

for M20A-FKS (w/ Canister Pump Module): Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

for M20A-FKS (w/o Canister Pump Module): Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

for 2ZR-FAE (w/ Canister Pump Module): Click here 2023 MY Corolla [09/2022 - 11/2022]; 2ZR-FAE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module): REMOVAL

for 2ZR-FAE (w/o Canister Pump Module): Click here 2023 MY Corolla [09/2022 - 11/2022]; 2ZR-FAE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module): REMOVAL

OK

13.

INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

*a

Component without harness connected

(Fuel Suction Tube with Pump and Gauge Assembly)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance (for M20A-FKS):

Tester Connection

Condition

Specified Condition

O46-1 (FV) - A-3

Always

Below 1 Ω

O46-2 (FE) - A-2

Always

Below 1 Ω

O46-3 (FS) - A-1

Always

Below 1 Ω

O46-1 (FV) - O46-3 (FS)

or

A-3 - A-1

Always

10 kΩ or higher

O46-1 (FV) - O46-2 (FE)

or

A-3 - A-2

Always

10 kΩ or higher

O46-2 (FE) - O46-3 (FS)

or

A-2 - A-1

Always

10 kΩ or higher

Standard Resistance (for 2ZR-FAE):

Tester Connection

Condition

Specified Condition

O44-1 (FV) - A-3

Always

Below 1 Ω

O44-2 (FE) - A-2

Always

Below 1 Ω

O44-3 (FS) - A-1

Always

Below 1 Ω

O44-1 (FV) - O44-3 (FS)

or

A-3 - A-1

Always

10 kΩ or higher

O44-1 (FV) - O44-2 (FE)

or

A-3 - A-2

Always

10 kΩ or higher

O44-2 (FE) - O44-3 (FS)

or

A-2 - A-1

Always

10 kΩ or higher

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

for 2ZR-FAE (w/ Canister Pump Module): Click here 2023 MY Corolla [09/2022 - 11/2022]; 2ZR-FAE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module): REMOVAL

for 2ZR-FAE (w/o Canister Pump Module): Click here 2023 MY Corolla [09/2022 - 11/2022]; 2ZR-FAE (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module): REMOVAL

for M20A-FKS (w/ Canister Pump Module): Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/ Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

for M20A-FKS (w/o Canister Pump Module): Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; M20A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (w/o Canister Pump Module (for Double Wishbone Type Suspension)): REMOVAL

OK

14.

CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the I4 combination meter assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance (for M20A-FKS):

Tester Connection

Condition

Specified Condition

O46-1 (FV) - I4-14 (FV)

Always

Below 1 Ω

O46-3 (FS) - I4-31 (FR)

Always

Below 1 Ω

O46-2 (FE) - I4-24 (FE&B)

Always

Below 1 Ω

O46-1 (FV) or I4-14 (FV) - Body ground

Always

10 kΩ or higher

O46-3 (FS) or I4-31 (FR) - Body ground

Always

10 kΩ or higher

Standard Resistance (for 2ZR-FAE):

Tester Connection

Condition

Specified Condition

O44-1 (FV) - I4-14 (FV)

Always

Below 1 Ω

O44-3 (FS) - I4-31 (FR)

Always

Below 1 Ω

O44-2 (FE) - I4-24 (FE&B)

Always

Below 1 Ω

O44-1 (FV) or I4-14 (FV) - Body ground

Always

10 kΩ or higher

O44-3 (FS) or I4-31 (FR) - Body ground

Always

10 kΩ or higher

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR