Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000002579K |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for 12.3 Inch Display): B132187; Lost Communication with EMV Missing Message; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ] |
DTC
|
B132187
|
Lost Communication with EMV Missing Message
|
DESCRIPTION
After the combination meter assembly has started, the combination meter assembly attempts to detect the radio and display receiver assembly by performing communication via local bus.
This DTC is stored when the radio and display receiver assembly has been detected but communication between the combination meter assembly and radio and display receiver assembly is interrupted.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B132187
|
Lost Communication with EMV Missing Message
|
Diagnosis Condition:
-
The combination meter assembly has started
-
The radio and display receiver assembly has started
Malfunction Status:
-
After the radio and display receiver assembly is detected, communication via local bus is interrupted
|
-
Harness or connector
-
Radio and display receiver assembly
-
Combination meter assembly
|
WIRING DIAGRAM
CHECK POINT
-
When DTC B132187 is output from the combination meter assembly, other ECUs on the same detection circuit may simultaneously output the same DTC depending on the malfunctioning area.
-
Depending on the combination of DTCs simultaneously output by each ECU, the malfunctioning area can be narrowed down. Refer to the following table for DTC combinations output by each ECU.
DTC Output Pattern
|
DTC Output Part Name
(Display on GTS)
|
Malfunction Status/Suspected Area
|
Combination Meter Assembly
(Combination Meter)
|
Radio and Display Receiver Assembly
(Navigation System)
|
1
|
B132187
|
U11D087
|
-
Radio and display receiver assembly
-
Harness or connector
-
Combination meter assembly
|
2
|
B132187
|
Not output
|
-
Radio and display receiver assembly
-
Combination meter assembly
|
CAUTION / NOTICE / HINT
NOTICE:
-
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
-
When replacing the combination meter assembly, update the ECU security key.
Click here
-
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
-
If the power source circuit for any of the following ECUs is malfunctioning, DTCs may not be correctly output. Therefore, before performing troubleshooting using the following procedure, perform inspections related to the power source circuit of each ECU.
-
Radio and display receiver assembly
Click here
-
Combination meter assembly
Click here
PROCEDURE
(a) Check each system for DTCs.
Body Electrical > Combination Meter > Trouble Codes
Body Electrical > Navigation System > Trouble Codes
(b) Confirm the DTC combinations of the following table.
DTC Output Pattern
|
DTC Output Part Name
(Display on GTS)
|
Combination Meter Assembly
(Combination Meter)
|
Radio and Display Receiver Assembly
(Navigation System)
|
1
|
B132187
|
U11D087
|
2
|
B132187
|
Not output
|
Result
|
Proceed to
|
DTC output pattern 1
|
A
|
DTC output pattern 2
|
B
|
A
|
|
|
2.
|
INSPECT EACH ECU (INTERNAL MALFUNCTION)
|
(a) Remove 1 of the following ECUs.
-
Radio and display receiver assembly
HINT:
Click here
-
Combination meter assembly
HINT:
Click here
(b) Measure the resistance of the removed ECU.
NOTICE:
-
Refer to the following table for the specified conditions of each ECU.
-
If the specified conditions are met, repeat the inspection procedure from step (a) for another ECU.
HINT:
If the results of an ECU are not as specified, it is suspected that the ECU is the cause of the DTC.
(1) Inspect the radio and display receiver assembly.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I175-11 (CNH1) - I175-12 (CNL1)
|
Always
|
108 to 132 Ω
|
|
|
*a
|
Component without harness connected
(Radio and Display Receiver Assembly)
|
|
|
(2) Inspect the combination meter assembly.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I5-32 (TX+) - I5-15 (TX-)
|
Always
|
108 to 132 Ω
|
Result:
Result
|
Proceed to
|
The results of all ECUs are as specified
|
A
|
The results of the radio and display receiver assembly is not as specified
|
B
|
The results of the combination meter assembly is not as specified
|
C
|
|
|
*a
|
Component without harness connected
(Combination Meter Assembly)
|
|
|
A |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
(a) Clear the DTCs.
Body Electrical > Combination Meter > Clear DTCs
NEXT
|
|
|
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
HINT:
By disconnecting the cable from the negative (-) auxiliary battery terminal, the internally stored information related to local bus communication for the combination meter assembly is reset.
(b) Disconnect the I175 radio and display receiver assembly connector.
(c) Connect the cable to the negative (-) auxiliary battery terminal.
(d) Turn the ignition switch to ON.
(e) Wait 30 seconds or more.
(f) Check for DTCs.
Body Electrical > Combination Meter > Trouble Codes
HINT:
By resetting the internally stored information related to local bus communication, the detection conditions of DTC B132187 are not met as the combination meter assembly does not detect the radio and display receiver assembly. If the combination meter assembly is operating normally, DTC B132187 will not be stored.
Result
|
Proceed to
|
DTC B132187 is not output
|
A
|
DTC B132187 is output
|
B
|
|