Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000002579A |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for 12.3 Inch Display): B150718; Turn Signal Light Circuit Current Below Threshold; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ] |
DTC
|
B150718
|
Turn Signal Light Circuit Current Below Threshold
|
DESCRIPTION
This DTC is stored when the combination meter assembly detects an open in a front turn signal light circuit or rear turn signal light circuit.
HINT:
-
If there is an open in a front turn signal light circuit or rear turn signal light circuit, the turn signal lights on the side with the open circuit will blink faster than usual.
-
If there is an open in a side turn signal light circuit, DTC B150718 will not be stored.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B150718
|
Turn Signal Light Circuit Current Below Threshold
|
Diagnosis Condition:
-
Auxiliary battery voltage is 10 V or more
Malfunction Status:
-
Open in front turn signal light circuit
-
Open in rear turn signal light circuit
|
-
Headlight assembly
-
Rear Combination Light Assembly
-
Rear turn signal light LED
-
Harness or connector
-
Combination meter assembly
|
WIRING DIAGRAM
LH SIDE
RH SIDE
CAUTION / NOTICE / HINT
NOTICE:
-
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
-
Inspect the turn signal light bulbs before performing the following procedure.
-
When replacing the combination meter assembly, update the ECU security key.
Click here
PROCEDURE
(a) Inspect the illumination of each turn signal light.
Result
|
Proceed to
|
Front turn signal light LH does not blink
|
A
|
Rear turn signal light LH does not blink
|
B
|
Front turn signal light RH does not blink
|
C
|
Rear turn signal light RH does not blink
|
D
|
A
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
|
(a) Disconnect the A170 headlight assembly LH connector.
(b) Disconnect the I5 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A170-6 (B) - I5-5 (LL)
|
Always
|
Below 1 Ω
|
A170-3 (E) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
CHECK TURN SIGNAL LIGHT (HEADLIGHT ASSEMBLY LH)
|
(a) Remove the headlight assembly LH.
HINT:
Click here
(b) Remove the Headlight Assembly RH.
HINT:
Click here
(c) Interchange the Headlight Assembly LH with RH and connect the connectors.
(d) Check the front turn signal light (LH side) operates normally.
Result
|
Proceed to
|
Problem symptoms do not change
(Front turn signal light (LH side) does not blink)
|
A
|
Front turn signal light (LH side) operates normally
|
B
|
4.
|
CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
|
(a) Disconnect the O43 rear combination light assembly LH connector.
(b) Disconnect the I5 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
O43-4 (B) - I5-22 (TRNL)
|
Always
|
Below 1 Ω
|
O43-3 (E) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
5.
|
INSPECT REAR COMBINATION LIGHT ASSEMBLY LH
|
Click here
6.
|
CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
|
(a) Disconnect the A171 headlight assembly RH connector.
(b) Disconnect the I5 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A171-6 (B) - I5-6 (LR)
|
Always
|
Below 1 Ω
|
A171-3 (E) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
7.
|
CHECK TURN SIGNAL LIGHT (HEADLIGHT ASSEMBLY RH)
|
(a) Remove the headlight assembly RH.
HINT:
Click here
(b) Remove the Headlight Assembly LH.
HINT:
Click here
(c) Interchange the Headlight Assembly RH with LH and connect the connectors.
(d) Check the front turn signal light (RH side) operates normally.
Result
|
Proceed to
|
Problem symptoms do not change
(Front turn signal light (RH side) does not blink)
|
A
|
Front turn signal light (RH side) operates normally
|
B
|
8.
|
CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
|
(a) Disconnect the O42 rear combination light assembly RH connector.
(b) Disconnect the I5 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
O42-4 (B) - I5-21 (TRNR)
|
Always
|
Below 1 Ω
|
O42-3 (E) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
9.
|
INSPECT REAR COMBINATION LIGHT ASSEMBLY RH
|
Click here
|