Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000255X5 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: G16E-GTS (ENGINE CONTROL): SFI SYSTEM: P253314; Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open; 2023 - 2025 MY GR Corolla [09/2022 - ] |
DTC
|
P253314
|
Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open
|
DESCRIPTION
When the ignition switch is turned to ON, the battery power source is supplied to the IGP and IGR terminals of the ECM. When the ignition switch is off, the battery power source is cut off.
When the ignition switch is turned off during driving, the battery power source supplied to the IGP terminal is cut off. However, the battery power source supplied to the IGR terminal is supplied until the vehicle is stopped and the ignition switch is turned off.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Note
|
P253314
|
Ignition Switch On/Start Position Circuit Low Circuit Short to Ground or Open
|
Short to ground or open in IGR terminal circuit (2 trip detection logic).
|
-
Power Distribution Box Assembly
-
Wire harness or connector
-
ECM
|
Does not come on
|
SAE Code: P2534
|
MONITOR DESCRIPTION
The ECM stores a DTC when there is no battery voltage to the IGR terminal even though there is battery voltage to the IGP terminal.
WIRING DIAGRAM
CONFIRMATION DRIVING PATTERN
-
Connect the GTS to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the GTS on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
-
Turn the ignition switch to ON.
-
Turn the GTS on.
-
Wait 1 minute or more.
-
Enter the following menus: Powertrain / Engine / Trouble Codes.
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P253314
-
Check the DTC judgment result.
GTS Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system is malfunctioning.
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
READ VALUE USING GTS (IGR)
|
(a) Read the Data List.
Powertrain > Engine > Data List
Result
|
Proceed to
|
The value of IGR is ON
|
A
|
None of the above conditions are met
|
B
|
B
|
|
|
2.
|
CHECK TERMINAL VOLTAGE (IGR VOLTAGE)
|
(a) Disconnect the ECM connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
A139-13 (IGR) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Result:
|
|
*a
|
Front view of wire harness connector
(to ECM)
|
|
|
NG
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - ECM)
|
(a) Disconnect the ECM connector.
(b) Disconnect the power distribution box assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
8F-8 - A139-13 (IGR)
|
Always
|
Below 1 Ω
|
8F-8 or A139-13 (IGR) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - BODY GROUND)
|
(a) Disconnect the power distribution box assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
8A-8 - Body ground
|
Always
|
Below 1 Ω
|
8D-8 - Body ground
|
Always
|
Below 1 Ω
|
OK |
|
REPLACE POWER DISTRIBUTION BOX ASSEMBLY
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|