Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000255VJ
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 -           ]
Title: G16E-GTS (ENGINE CONTROL): SFI SYSTEM: P001600,P001700; Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A; 2023 - 2025 MY GR Corolla [09/2022 -        ]

DTC

P001600

Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A

DTC

P001700

Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B

DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft, cam timing oil control solenoid assembly, camshaft timing valve assembly (camshaft timing oil control valve) and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Note

P001600

Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A

Deviation in the crankshaft position sensor signal and camshaft sensor (for intake camshaft) signal (2 trip detection logic).

  • Valve timing
  • Cam timing oil control solenoid assembly (for intake camshaft)
  • Camshaft timing valve assembly (intake camshaft timing oil control valve)
  • Camshaft timing gear assembly
  • ECM

Comes on

SAE Code: P0016

P001700

Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B

Deviation in the crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal (2 trip detection logic).

  • Valve timing
  • Cam timing oil control solenoid assembly (for exhaust camshaft)
  • Camshaft timing valve assembly (exhaust camshaft timing oil control valve)
  • Camshaft timing exhaust gear assembly
  • ECM

Comes on

SAE Code: P0017

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the neutral position while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P001600.

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P001700.

MONITOR DESCRIPTION

Related DTCs

P0016: Camshaft timing misalignment at idling (for intake camshaft)

P0017: Camshaft timing misalignment at idling (for exhaust camshaft)

Required Sensors/Components (Main)

Camshaft timing gear assembly

Camshaft timing exhaust gear assembly

Required Sensors/Components (Related)

Camshaft position sensor

Crankshaft position sensor

Frequency of Operation

Continuous

Duration

Within 1 minute

MIL Operation

2 driving cycles

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

Engine speed

500 to 1200 rpm

TYPICAL MALFUNCTION THRESHOLDS

P0016: Camshaft timing misalignment at idling (for intake camshaft)

Either of the following conditions is met

A or B

A. VVT learned value at maximum retarded valve timing

Less than 16.6°CA (Crankshaft Angle)

B. VVT learned value at maximum retarded valve timing

More than 39.2°CA (Crankshaft Angle)

P0017: Camshaft timing misalignment at idling (for exhaust camshaft)

Either of the following conditions is met

A or B

A. VVT learned value at maximum advanced valve timing

Less than 106.1°CA (Crankshaft Angle)

B. VVT learned value at maximum advanced valve timing

More than 128.7°CA (Crankshaft Angle)

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON [A].
  7. Turn the GTS on.
  8. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  9. Idle the engine for 5 minutes or more [C].
  10. Enter the following menus: Powertrain / Engine / Trouble Codes [D].
  11. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  13. Input the DTC: P001600 or P001700.
  14. Check the DTC judgment result.

    GTS Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform steps [E] through [G].
    • [A] to [D]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
  15. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  16. Idle the engine for 5 minutes or more [F].
  17. Enter the following menus: Powertrain / Engine / Trouble Codes [G].
  18. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  19. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • [A] to [G]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

HINT:

  • The monitor for this DTC detects when the timing chain is shifted by two teeth or more.
  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600 OR P001700)

(a) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

P001600 or P001700 and other DTCs are output

A

P001600 or P001700 is output

B

HINT:

If any DTCs other than P001600 or P001700 is output, troubleshoot those DTCs first.

A

GO TO DTC CHART

B

2.

PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1 OR CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)

HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

(a) Start the engine.

(b) Perform the Active Test. Check that the displacement angle varies.

Powertrain > Engine > Active Test

Active Test Display

Control the Intake VVT OCV Duty Ratio Bank 1

Data List Display

Intake VVT Change Angle Bank 1

Intake VVT OCV Control Duty Ratio Bank 1

Powertrain > Engine > Active Test

Active Test Display

Control the Exhaust VVT OCV Duty Ratio Bank 1

Data List Display

Exhaust VVT Change Angle Bank 1

Exhaust VVT OCV Control Duty Ratio Bank 1

OK:

Displacement angle varies.

NG

GO TO STEP 4

OK

3.

CHECK ENGINE MECHANICAL SYSTEM

(a) Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE MECHANICAL): ENGINE UNIT: DISASSEMBLY

OK

GO TO STEP 9

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

4.

INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): CAMSHAFT OIL CONTROL SOLENOID: INSPECTION

NG

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)

OK

5.

INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): CAMSHAFT OIL CONTROL SOLENOID: INSPECTION

NG

REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)

OK

6.

INSPECT CAMSHAFT TIMING VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): CAMSHAFT OIL CONTROL VALVE (for Intake Side): ON-VEHICLE INSPECTION

NG

REPLACE CAMSHAFT TIMING VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING OIL CONTROL VALVE)

OK

7.

INSPECT CAMSHAFT TIMING VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING OIL CONTROL VALVE)

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): CAMSHAFT OIL CONTROL VALVE (for Exhaust Side): ON-VEHICLE INSPECTION

NG

REPLACE CAMSHAFT TIMING VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING OIL CONTROL VALVE)

OK

8.

CLEAR DTC

(a) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(b) Turn the ignition switch off and wait for at least 30 seconds.

NEXT

9.

CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)

(a) Start the engine and warm it up.

(b) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

(c) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

P001600 or P001700 is output

B

A

CHECK FOR INTERMITTENT PROBLEMS

B

10.

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Click here 2023 MY GR Corolla [09/2022 - 11/2022]; G16E-GTS (ENGINE MECHANICAL): CAMSHAFT: REMOVAL 2023 - 2025 MY GR Corolla [11/2022 -        ]; G16E-GTS (ENGINE MECHANICAL): CAMSHAFT: REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click here 2023 - 2025 MY GR Corolla [09/2022 -        ]; G16E-GTS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

NEXT

11.

CLEAR DTC

(a) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(b) Turn the ignition switch off and wait for at least 30 seconds.

NEXT

12.

CHECK WHETHER DTC OUTPUT RECURS (DTC P001600 OR P001700)

(a) Start the engine and warm it up.

(b) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

(c) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

P001600 or P001700 is output

B

A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM 2023 MY GR Corolla [09/2022 - 11/2022]; G16E-GTS (ENGINE CONTROL): ECM: REMOVAL 2023 - 2025 MY GR Corolla [11/2022 -        ]; G16E-GTS (ENGINE CONTROL): ECM: REMOVAL