Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000255VI |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: G16E-GTS (ENGINE CONTROL): SFI SYSTEM: P001400,P001500; Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1; 2023 - 2025 MY GR Corolla [09/2022 - ] |
DTC
|
P001400
|
Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1
|
DTC
|
P001500
|
Camshaft Position "B" - Timing Over-Retarded Bank 1
|
DESCRIPTION
Refer to DTC P001313.
Click here
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Note
|
P001400
|
Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1
|
Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic).
|
-
Valve timing
-
Cam timing oil control solenoid assembly
-
Camshaft timing oil control valve assembly (exhaust camshaft timing valve assembly)
-
Camshaft timing exhaust gear assembly
-
ECM
|
Comes on
|
SAE Code: P0014
|
P001500
|
Camshaft Position "B" - Timing Over-Retarded Bank 1
|
Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic).
|
-
Valve timing
-
Cam timing oil control solenoid assembly
-
Camshaft timing oil control valve assembly (exhaust camshaft timing valve assembly)
-
Camshaft timing exhaust gear assembly
-
ECM
|
Comes on
|
SAE Code: P0015
|
MONITOR DESCRIPTION
The ECM optimizes the exhaust valve timing using the Variable Valve Timing (VVT) system to control the exhaust camshaft. The VVT system includes the ECM, cam timing oil control solenoid assembly, camshaft timing oil control valve assembly (exhaust camshaft timing valve assembly) and camshaft timing exhaust gear assembly. The ECM sends a target duty-cycle control signal to the cam timing oil control solenoid assembly. The camshaft timing oil control valve assembly (exhaust camshaft timing valve assembly) is operated to control the oil pressure supplied to the camshaft timing exhaust gear assembly based on this signal. The camshaft timing gear assembly can advance or retard the exhaust camshaft.
If the difference between the target and actual exhaust valve timing is large, and changes in the actual exhaust valve timing are small, the ECM interprets this as the camshaft timing exhaust gear assembly stuck malfunction and stores a DTC.
-
Example:
-
A DTC is stored when the following conditions are met:
-
It takes 5 seconds or more to change the valve timing by 5°CA.
-
After the above condition is met, the cam timing oil control solenoid assembly is forcibly activated for 9.5 seconds.
These DTCs indicate that the camshaft timing exhaust gear assembly cannot operate properly due to a camshaft timing oil control valve assembly (exhaust camshaft timing valve assembly) malfunction or the presence of foreign matter in the camshaft timing oil control valve assembly (exhaust camshaft timing valve assembly).
MONITOR STRATEGY
Related DTCs
|
P0014: Advanced camshaft timing (for exhaust camshaft)
P0015: Retarded camshaft timing (for exhaust camshaft)
|
Required Sensors/Components (Main)
|
Cam timing oil control solenoid assembly (for exhaust camshaft)
Camshaft timing oil control valve assembly (exhaust camshaft timing valve assembly)
Camshaft timing exhaust gear assembly
|
Required Sensors/Components (Related)
|
Crankshaft position sensor
Camshaft position sensor
Engine coolant temperature sensor
|
Frequency of Operation
|
Continuous: P0014, P0015
|
Duration
|
Within 10 seconds
|
MIL Operation
|
2 driving cycles: P0014
Immediate: P0015
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
P0013 (Exhaust VVT oil control solenoid)
P0017 (Exhaust VVT system - misalignment)
P0101, P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0335, P0337, P0338 (Crankshaft position sensor)
P0340, P0342, P0343 (Camshaft position sensor)
P0365, P0367, P0368 (Exhaust camshaft position sensor)
|
Battery voltage
|
11 V or higher
|
Engine speed
|
500 to 4000 rpm
|
Engine coolant temperature
|
75 to 100°C (167 to 212°F)
|
TYPICAL MALFUNCTION THRESHOLDS
P0014: Advanced Camshaft Timing
Both of the following conditions are met
|
-
|
Deviation of actual valve timing and target valve timing
|
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit
|
Valve timing
|
No change at advanced valve timing
|
P0015: Retarded Camshaft Timing
Both of the following conditions are met
|
-
|
Deviation of actual valve timing and target valve timing
|
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit
|
Valve timing
|
No change at retarded valve timing
|
If the difference between the target and actual camshaft timing is greater than the specified value, the ECM operates the VVT actuator for 10 seconds by applying and releasing oil pressure. Then, the ECM monitors the camshaft timing change for 10 seconds.
MONITOR RESULT
Refer to detailed information in Checking Monitor Status.
Click here
P0014, P0015: Exhaust Gas Recirculation/VVT / EX VVT STUCK B1
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$35
|
$85
|
Multiply by 0.01
|
Second
|
Forced movement of oil control solenoid time
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the GTS to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the GTS on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
-
Turn the ignition switch to ON [A].
-
Turn the GTS on.
-
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
-
Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
-
Idle the engine for 3 minutes or more [D].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [E].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P001400 or P001500.
-
Check the DTC judgment result.
GTS Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
-
Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
Depress the accelerator pedal by a large amount.
-
Idle the engine for 3 minutes or more [G].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [H].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Check the DTC judgment result again.
WIRING DIAGRAM
Refer to DTC P001313.
Click here
CAUTION / NOTICE / HINT
HINT:
-
DTC P001400 or P001500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.
-
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001400 OR P001500)
|
(a) Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
|
Proceed to
|
P001400 or P001500 and other DTCs are output
|
A
|
P001400 or P001500 is output
|
B
|
HINT:
If any DTCs other than P001400 or P001500 are output, troubleshoot those DTCs first.
A |
|
GO TO DTC CHART
|
B
|
|
|
2.
|
PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
|
(a) Start the engine.
(b) Read the Data List while performing the Active Test with the engine idling.
Powertrain > Engine > Active Test
Active Test Display
|
Control the Exhaust VVT OCV Duty Ratio Bank 1
|
Data List Display
|
Exhaust VVT Change Angle Bank 1
|
Standard:
GTS Operation
|
Data List (Exhaust VVT Change Angle Bank 1)
|
-100% to 100%
|
Varies by 30 DegFR or more
|
OK
|
|
|
(a) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(b) Turn the ignition switch off and wait for at least 30 seconds.
NEXT
|
|
|
4.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
|
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Read the DTCs.
Powertrain > Engine > Trouble Codes
HINT:
DTC P001400 or P001500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.
Result
|
Proceed to
|
DTCs are not output
|
A
|
P001400 or P001500 is output
|
B
|
B
|
|
|
5.
|
INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
|
Click here
OK
|
|
|
6.
|
INSPECT CAMSHAFT TIMING VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING OIL CONTROL VALVE)
|
Click here
7.
|
REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR EXHAUST CAMSHAFT)
|
Click here
NEXT
|
|
|
8.
|
INSPECT CAMSHAFT TIMING VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING OIL CONTROL VALVE)
|
Click here
NG
|
|
|
9.
|
REPLACE CAMSHAFT TIMING VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING OIL CONTROL VALVE)
|
Click here
NEXT
|
|
|
10.
|
PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
|
(a) Start the engine.
(b) Read the Data List while performing the Active Test with the engine idling.
Powertrain > Engine > Active Test
Active Test Display
|
Control the Exhaust VVT OCV Duty Ratio Bank 1
|
Data List Display
|
Exhaust VVT Change Angle Bank 1
|
Standard:
GTS Operation
|
Data List (Exhaust VVT Change Angle Bank 1)
|
-100% to 100%
|
Varies by 30 DegFR or more
|
OK |
|
END
|
NG
|
|
|
11.
|
CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
|
*1
|
Crankshaft Timing Gear Key
|
-
|
-
|
*a
|
Timing Mark
|
*b
|
Approximately 27°
|
(a) Remove the cylinder head cover sub-assembly and timing chain cover assembly.
Click here
(b) Temporarily install the crankshaft pulley bolt.
(c) Rotate the crankshaft in the correct direction until the timing mark of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are located at the top.
(d) Check that the crankshaft timing gear key as shown in the illustration.
HINT:
If the crankshaft timing gear key moves from the position shown in the illustration, check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
(e) Remove the crankshaft pulley bolt.
HINT:
As the exhaust camshaft sub-assembly may rotate counterclockwise strongly when the crankshaft pulley set bolt is removed, use a wrench to hold the hexagonal portion of the exhaust camshaft sub-assembly.
NEXT
|
|
|
12.
|
CHECK ENGINE MECHANICAL SYSTEM
|
(a) Inspect the components that affect the valve timing.
Click here
HINT:
Perform the following inspections.
-
Chain sub-assembly
-
Camshaft timing gear assembly
-
Camshaft timing exhaust gear assembly
-
Crankshaft timing gear or sprocket
-
No. 1 chain tensioner assembly
-
Chain tensioner slipper
-
No. 1 chain vibration damper
NG |
|
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
|
OK
|
|
|
13.
|
REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
|
Click here
HINT:
Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.
Click here
NEXT
|
|
|
(a) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(b) Turn the ignition switch off and wait for at least 30 seconds.
NEXT
|
|
|
15.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
|
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Read the DTCs.
Powertrain > Engine > Trouble Codes
HINT:
DTC P001400 or P001500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.
Result
|
Proceed to
|
DTCs are not output
|
A
|
P001400 or P001500 is output
|
B
|
|