Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000255UD |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: G16E-GTS (ENGINE CONTROL): SFI SYSTEM: P060D49; Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure; 2023 - 2025 MY GR Corolla [09/2022 - ] |
DTC
|
P060D49
|
Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure
|
MONITOR DESCRIPTION
The ECM monitors the input signals of the No. 1 accelerator pedal position sensor. If the input signals and control signals deviate, this DTC is stored.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Note
|
P060D49
|
Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure
|
Either of the following conditions is met (1 trip detection logic):
-
There is an ECM main CPU error.
-
There is an ECM sub CPU error.
|
ECM
|
Comes on
|
SAE Code: P060D
|
MONITOR STRATEGY
Related DTCs
|
P060D: Internal control module accelerator pedal position performance
|
Required Sensors/Components (Main)
|
ECM
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
1 second
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
TYPICAL MALFUNCTION THRESHOLDS
Difference of main accelerator pedal position and sub accelerator pedal position
|
0.3 V or higher
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the GTS to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the GTS on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the GTS off.
-
Turn the ignition switch off.
-
Disconnect the GTS.
-
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
-
Connect the cable to the negative (-) battery terminal.
-
Connect the GTS to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the GTS on.
-
Wait 16 seconds or more [A].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P060D49.
-
Check the DTC judgment result.
GTS Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
(a) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(b) Turn the ignition switch off.
NEXT
|
|
|
2.
|
READ OUTPUT DTC (DTC P060D49)
|
(a) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(b) Connect the cable to the negative (-) battery terminal.
(c) Wait 16 seconds or more.
(d) Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
P060D49 is output
|
B
|
|