Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM10000000255U9 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: G16E-GTS (ENGINE CONTROL): SFI SYSTEM: P056014; System Voltage Circuit Short to Ground or Open; 2023 - 2025 MY GR Corolla [09/2022 - ] |
DTC
|
P056014
|
System Voltage Circuit Short to Ground or Open
|
MONITOR DESCRIPTION
The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, Freeze Frame Data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. The next time the engine is started, the ECM will illuminate the MIL and store this DTC.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P056014
|
System Voltage Circuit Short to Ground or Open
|
An open or short in the ECM backup power source circuit (1 trip detection logic).
|
-
Open or short in backup power source circuit
-
Battery
-
Battery terminals
-
ECM
|
Comes on
|
DTC stored
|
SAE Code: P0562
|
MONITOR STRATEGY
Related DTCs
|
P0562: ECM system voltage range check (low voltage)
|
Required Sensors/Components (Main)
|
ECM
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
3 seconds
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
All of the following conditions are met
|
-
|
Battery voltage
|
8 V or higher
|
Ignition switch
|
ON
|
Starter
|
Off
|
TYPICAL MALFUNCTION THRESHOLDS
Continuous battery voltage
|
Less than 3.5 V
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the GTS to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the GTS on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
-
Turn the ignition switch to ON.
-
Turn the GTS on.
-
Wait 5 seconds or more [A].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P056014.
-
Check the DTC judgment result.
GTS Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
(a) Inspect that the battery is not depleted.
Click here
OK:
Battery is not depleted
NG |
|
CHARGE OR REPLACE BATTERY
|
OK
|
|
|
(a) Check that the battery terminals are not loose or corroded.
OK:
Battery terminals are not loose or corroded.
NG |
|
REPAIR OR REPLACE BATTERY TERMINAL
|
OK
|
|
|
3.
|
CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
|
(a) Disconnect the ECM connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
A139-1(BATT) - Body ground
|
Always
|
11 to 14 V
|
|
|
*a
|
Front view of wire harness connector
(to ECM)
|
|
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)
|
OK
|
|
|
(a) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(b) Turn the ignition switch off and wait for at least 30 seconds.
NEXT
|
|
|
5.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P056014)
|
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
P056014 is output
|
B
|
|