| Last Modified: 01-27-2025 | 6.11:8.1.0 | Doc ID: RM10000000255TS |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 09/2024] |
| Title: G16E-GTS (ENGINE CONTROL): SFI SYSTEM: TERMINALS OF ECM; 2023 - 2025 MY GR Corolla [09/2022 - 09/2024] | ||
TERMINALS OF ECM
HINT:
The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
|
Terminal No. (Symbol) |
Terminal Description |
Condition |
Specified Condition |
|---|---|---|---|
|
A139-1(BATT) - A139-10(E1) |
Battery (for measuring battery voltage and ECM memory) |
Always |
11 to 14 V |
|
A139-2(IGP) - A139-10(E1) |
Ignition switch signal |
Ignition switch ON |
11 to 14 V |
|
A139-3 (VPMP) - A139-10 (E1) |
Vent valve (built into canister pump module) |
Ignition switch ON |
11 to 14 V |
|
A139-5 (MPMP) - A139-10 (E1) |
Leak detection pump (canister pump module) |
Leak detection pump OFF |
Below 3 V |
|
Leak detection pump ON |
11 to 14 V |
||
|
A139-6(FPC) - A139-10(E1) |
Fuel pump control |
Engine stopped, ignition switch ON |
0 to 1.5 V |
|
A139-8(CANH) - A139-10(E1) |
CAN communication line |
Engine stopped, ignition switch ON |
Pulse generation (See waveform 1) |
|
A139-9(+B) - A139-10(E1) |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
|
A139-10(E1) - Body ground |
Ground |
Always |
Below 1 Ω |
|
A139-13(IGR) - A139-10(E1) |
Ignition signal |
Ignition switch ON |
11 to 14 V |
|
A139-15(MREL) - A139-10(E1) |
EFI-MAIN relay operation signal |
Engine stopped, ignition switch ON |
0 to 1.5 V |
|
A139-16(NEO) - A139-10(E1) |
Engine speed signal sent to other ECUs |
Idling with warm engine |
Pulse generation (See waveform 2) |
|
A139-18(CANL) - A139-10(E1) |
CAN communication line |
Engine stopped, ignition switch ON |
Pulse generation (See waveform 3) |
|
A139-21(STP) - A139-10(E1) |
Stop light switch assembly signal |
Brake pedal depressed |
7.5 to 14 V |
|
Brake pedal released |
0 to 1.5 V |
||
|
A139-22(ST1-) - A139-10(E1) |
Stop light switch assembly signal (opposite to STP terminal) |
Ignition switch ON, brake pedal depressed |
0 to 1.5 V |
|
Ignition switch ON, brake pedal released |
7.5 to 14 V |
||
|
A139-23(NSW) - A139-10(E1) |
Clutch start switch signal |
Ignition switch ON, clutch pedal fully released |
11 to 14 V |
|
Ignition switch ON, clutch pedal depressed |
Below 3.0 V |
||
|
A139-25(CANU) - A139-10(E1) |
CAN communication line |
Engine stopped, ignition switch ON |
Pulse generation (See waveform 1) |
|
A139-26(CAND) - A139-10(E1) |
CAN communication line |
Engine stopped, ignition switch ON |
Pulse generation (See waveform 3) |
|
A139-30(STA) - A139-10(E1) |
Starter assembly signal |
Cranking |
6 V or higher |
|
A139-32(RFC) - A139-10(E1) |
Cooling fan control signal |
Ignition switch ON, A/C switch on (max cool) |
Pulse generation (See waveform 4) |
|
A139-34(IREL) - A139-10(E1) |
EDU relay operation signal |
Ignition switch ON |
0 to 1.5 V |
|
A139-35(+B2) - A139-10(E1) |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
|
A139-36(E01) - Body ground |
Ground |
Always |
Below 1 Ω |
|
A139-39(KSW) - A139-10(E1) |
Key in vehicle signal |
Ignition switch ON |
0 to 3 V |
|
A139-42(SPD) - A139-10(E1) |
Vehicle speed signal from combination meter assembly |
Driving at 20 km/h (12 mph) |
Pulse generation (See waveform 5) |
|
A139-45(EC) - Body ground |
Ground |
Always |
Below 1 Ω |
|
A139-48 (VCPP) - A139-49 (EPPM) |
Power source for canister pressure sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
A139-50 (PPMP) - A139-49 (EPPM) |
Canister pressure sensor (built into canister pump module) |
Ignition switch ON |
3.0 to 3.6 V |
|
C142-19(+BD1) - A139-10(E1) |
Power source of ECU (injector driver) |
Ignition switch ON |
11 to 14 V |
|
A139-31 (DMS+) - A139-10 (E1) |
Drive mode select switch (combination switch assembly) signal |
Ignition switch ON, drive mode select switch (combination switch assembly) in neutral position |
11 to 14 V |
|
Ignition switch ON, drive mode select switch (combination switch assembly) pushed forward |
0 to 1.5 V |
||
|
A139-51 (DMS-) - A139-10 (E1) |
Drive mode select switch (combination switch assembly) signal |
Ignition switch ON, drive mode select switch (combination switch assembly) in neutral position |
11 to 14 V |
|
Ignition switch ON, drive mode select switch (combination switch assembly) pulled rearward |
0 to 1.5 V |
||
|
A139-53(E02) - Body ground |
Ground |
Always |
Below 1 Ω |
|
A139-54(E1D1) - Body ground |
Ground |
Always |
Below 1 Ω |
|
A139-55(VPA) - A139-56(EPA) |
Accelerator pedal position sensor signal (for engine control) |
Ignition switch ON, accelerator pedal fully released |
0.5 to 1.1 V |
|
Ignition switch ON, accelerator pedal fully depressed |
2.6 to 4.5 V |
||
|
A139-57(VCPA) - A139-56(EPA) |
Power source of accelerator pedal position sensor (for VPA) |
Engine stopped, ignition switch ON |
4.5 to 5.5 V |
|
A139-58(VPA2) - A139-59(EPA2) |
Accelerator pedal position sensor signal |
Ignition switch ON, accelerator pedal fully released |
1.2 to 2.0 V |
|
Ignition switch ON, accelerator pedal fully depressed |
3.4 to 4.75 V |
||
|
A139-60(VCP2) - A139-59(EPA2) |
Power source of accelerator pedal position sensor (for VPA2) |
Engine stopped, ignition switch ON |
4.5 to 5.5 V |
|
C142-5(EXM+) - A139-10(E1) |
exhaust pipe gas control actuator sub-assembly (drive motor) (positive terminal) |
Ignition switch ON |
Pulse generation |
|
C142-6(EXM-) - A139-10(E1) |
exhaust pipe gas control actuator sub-assembly (drive motor) (negative signal) |
Ignition switch ON |
Pulse generation |
|
C142-4(M-) - A139-10(E1) |
Throttle actuator operation signal (negative signal) |
Idling with warm engine |
Pulse generation (See waveform 6) |
|
C142-3(M+) - A139-10(E1) |
Throttle actuator operation signal (positive terminal) |
Idling with warm engine |
Pulse generation (See waveform 7) |
|
C142-1(HA1B) - A139-10(E1) |
Air fuel ratio sensor (sensor 2) heater operation signal |
Engine stopped, ignition switch ON |
11 to 14 V |
|
Idling with cold engine |
Pulse generation (See waveform 8) |
||
|
C142-2(HA1A) - A139-10(E1) |
Air fuel ratio sensor (sensor 1) heater operation signal |
Engine stopped, ignition switch ON |
11 to 14 V |
|
Idling with cold engine |
Pulse generation (See waveform 8) |
||
|
C142-14(#2D-) - A139-10(E1) |
Fuel injector assembly signal (No. 2 cylinder) |
Idling with warm engine |
Pulse generation (See waveform 9) |
|
C142-33(#2D+) - A139-10(E1) |
Fuel injector assembly signal (No. 2 cylinder) |
Idling with warm engine |
Pulse generation (See waveform 9) |
|
C142-35(#3D+) - A139-10(E1) |
Fuel injector assembly signal (No. 3 cylinder) |
Idling with warm engine |
Pulse generation (See waveform 9) |
|
C142-16(#3D-) - A139-10(E1) |
Fuel injector assembly signal (No. 3 cylinder) |
Idling with warm engine |
Pulse generation (See waveform 9) |
|
C142-31(#1D+) - A139-10(E1) |
Fuel injector assembly signal (No. 1 cylinder) |
Idling with warm engine |
Pulse generation (See waveform 9) |
|
C142-12(#1D-) - A139-10(E1) |
Fuel injector assembly signal (No. 1 cylinder) |
Idling with warm engine |
Pulse generation (See waveform 9) |
|
C142-10(FP1-) - A139-10(E1) |
Fuel pump assembly (for high pressure side) signal |
Idling with warm engine |
Pulse generation (See waveform 10) |
|
C142-29(FP1+) - A139-10(E1) |
Fuel pump assembly (for high pressure side) signal |
Idling with warm engine |
Pulse generation (See waveform 10) |
|
C142-25(OE1+) - C142-26(OE1-) |
Cam timing oil control solenoid assembly operation signal (for exhaust side) |
Idling |
Pulse generation (See waveform 11) |
|
C142-27(OC1+) - C142-28(OC1-) |
Cam timing oil control solenoid assembly operation signal (for intake side) |
Idling |
Pulse generation (See waveform 11) |
|
C143-32(VCEA) - C143-22(EEXA) |
Power source of exhaust pipe gas control actuator sub-assembly (opening angle sensor) |
Ignition switch ON |
4.5 to 5.5 V |
|
C143-34 (V1PC) - C143-24 (E1PC) |
Power source of vacuum sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
C143-39 (VCNP) - A139-10 (E1) |
Power source of neutral position switch |
Ignition switch ON |
4.5 to 5.5 V |
|
C143-42(EXA) - C143-22(EEXA) |
exhaust pipe gas control actuator sub-assembly (opening angle sensor) signal |
Ignition switch ON |
0.08 to 4.73 V |
|
C143-44 (PPC1) - C143-24 (E1PC) |
Vacuum sensor signal |
Idling with warm engine |
1.0 to 4.5 V |
|
C142-45(PRG) - A139-10(E1) |
Purge VSV operation signal |
Engine stopped, ignition switch ON |
11 to 14 V |
|
Idling with warm engine, under purge control |
Pulse generation (See waveform 12) |
||
|
C143-49 (NPSW) - C143-38 (ENPS) |
Neutral position switch signal |
Ignition switch ON, Shift lever in neutral |
2.7 to 4.3 V |
|
Ignition switch ON, Shift lever not in neutral |
0.7 to 1.9 V |
||
|
C143-53 (NIMB) - A139-10 (E1) |
Power supply for transmission revolution sensor |
Ignition switch ON |
11 to 14 V |
|
C143-54 (NIMO) - A139-10 (E1) |
Transmission revolution sensor signal |
Engine idling and clutch pedal fully released |
Pulse generation (See waveform 13) |
|
C142-70(IGT3) - A139-10(E1) |
No. 3 ignition coil assembly signal (ignition signal) |
Idling with warm engine |
Pulse generation (See waveform 14) |
|
C142-71(IGT2) - A139-10(E1) |
No. 2 ignition coil assembly signal (ignition signal) |
Idling with warm engine |
Pulse generation (See waveform 14) |
|
C142-72(IGT1) - A139-10(E1) |
No. 1 ignition coil assembly signal (ignition signal) |
Idling with warm engine |
Pulse generation (See waveform 14) |
|
C142-62(LIN) - A139-10(E1) |
LIN communication line |
Engine stopped, ignition switch ON |
Pulse generation (See waveform 15) |
|
C142-65(R) - A139-10(E1) |
Reverse signal |
Ignition switch ON, shift lever in R |
11 to 14 V |
|
C142-84(VCVG) - A139-10(E1) |
Power source of mass air flow meter sub-assembly (specific voltage) |
Ignition switch ON |
4.8 to 5.2 V |
|
C142-120(VCPF) - A139-10(E1) |
Power source of fuel pressure sensor (for low pressure side) (specific voltage) |
Ignition switch ON |
4.75 to 5.25 V |
|
C142-87(VTA2) - C142-110(ETA) |
Throttle position sensor signal (for sensor malfunction detection) |
Ignition switch ON, accelerator pedal fully released |
2.1 to 3.1 V |
|
Accelerator pedal fully depressed (engine running) |
4.6 to 5.0 V |
||
|
C142-88(VCV1) - A139-10(E1) |
Power source of camshaft position sensor (for intake camshaft) (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
C142-90(VV1+) - C142-89(VV1-) |
Camshaft position sensor (for intake camshaft) signal |
Idling with warm engine |
Pulse generation (See waveform 16) |
|
C142-91(EV1+) - C142-114(EV1-) |
Camshaft position sensor (for exhaust camshaft) signal |
Idling with warm engine |
Pulse generation (See waveform 16) |
|
C142-92(NE+) - C142-115(NE-) |
Crankshaft position sensor signal |
Idling with warm engine |
Pulse generation (See waveform 17) |
|
C142-97(PR) - C142-73(EPR) |
Fuel pressure sensor (for high pressure side) signal |
Idling with warm engine |
0.5 to 4.5 V |
|
C142-96(VCPR) - C142-73(EPR) |
Power source of fuel pressure sensor (for high pressure side) (specific voltage) |
Ignition switch ON |
4.75 to 5.25 V |
|
C142-77(VCPE) - C142-78(EPEO) |
Power source of oil pressure and temperature sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
C142-107(VG) - C142-83(E2G) |
Mass air flow meter sub-assembly signal |
Ignition switch ON |
Pulse generation (See waveform 18) |
|
C142-106(THA) - C142-83(E2G) |
Intake air temperature sensor (mass air flow meter sub-assembly) signal |
Idling, intake air temperature 0 to 80°C (32 to 176°F) |
0.5 to 3.4 V |
|
C142-121(PFL) - C142-119(EPFL) |
Fuel pressure sensor (for low pressure side) signal |
Idling with warm engine |
0.57 to 4.88 V |
|
C142-108(VTA1) - C142-110(ETA) |
Throttle position sensor signal (for engine control) |
Ignition switch ON, accelerator pedal fully released |
0.6 to 1.1 V |
|
Accelerator pedal fully depressed (engine running) |
3.2 to 4.8 V |
||
|
C142-109(VCTA) - C142-110(ETA) |
Power source of throttle position sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
C142-111(KNK1) - C142-112(EKNK) |
Knock control sensor signal |
Engine speed maintained at 4000 rpm after warming up engine |
Pulse generation (See waveform 19) |
|
C142-113(VCE1) - A139-10(E1) |
Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
C142-116(VCNE) - A139-10(E1) |
Power source of crankshaft position sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
C142-117(A1B-) - A139-10(E1) |
Air fuel ratio sensor (sensor 2) signal |
Ignition switch ON |
1.17 to 4.49 V |
|
C142-118(A1B+) - A139-10(E1) |
Air fuel ratio sensor (sensor 2) signal |
Ignition switch ON |
1.53 to 5.96 V |
|
C142-98(PIM) - C142-76(EPIM) |
No. 1 turbo pressure sensor signal |
Ignition switch ON |
3.0 to 4.5 V |
|
C142-75(VCPM) - C142-76(EPIM) |
Power source of No.1 turbo pressure sensor (specific voltage) |
Ignition switch ON |
4.75 to 5.25 V |
|
C142-100(PEO) - C142-78(EPEO) |
Engine oil pressure sensor (oil pressure and temperature sensor) signal |
Idling with warm engine |
0.5 to 4.5 V |
|
C142-101(THEO) - C142-78(EPEO) |
Engine oil pressure sensor (oil pressure and temperature sensor) signal |
Ignition switch ON |
0.54 to 4.86 V |
|
C142-129(THW) - C142-130(ETHW) |
Engine coolant temperature sensor signal |
Idling, engine coolant temperature 75 to 100°C (167 to 212°F) |
0.2 to 1.0 V |
|
C142-18(+BD3) - A139-10(E1) |
Power source of ECU (injector driver) |
Ignition switch ON |
11 to 14 V |
|
C142-38(+BD2) - A139-10(E1) |
Power source of ECU (injector driver) |
Ignition switch ON |
11 to 14 V |
|
C142-49(AICV) - A139-10(E1) |
Vacuum switching valve for air intake control valve operation signal |
Ignition switch ON |
11 to 14 V |
|
C142-20(ABV) - A139-10(E1) |
Air by-pass valve assembly operation signal |
Engine stopped, ignition switch ON |
11 to 14 V |
|
Air by-pass valve assembly operating |
Below 1.5 V |
||
|
C142-94(A1A-) - A139-10(E1) |
Air fuel ratio sensor (sensor 1) signal |
Ignition switch ON |
1.17 to 4.49 V |
|
C142-95(A1A+) - A139-10(E1) |
Air fuel ratio sensor (sensor 1) signal |
Ignition switch ON |
1.53 to 5.96 V |
|
C142-99(THIM) - A139-10(E1) |
Intake air temperature sensor (No. 1 turbo pressure sensor) signal |
Idling with warm engine |
0 to 5.25 V |
|
C142-82(VCPC) - C142-81(EPIC) |
Power source of Vacuum sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
C142-105(PIC) - C142-81(EPIC) |
Vacuum sensor signal |
Idling with warm engine |
1.0 to 4.5 V |
|
C142-80(VPTA) - C142-79(EPTA) |
Power source of No.2 turbo pressure sensor (specific voltage) |
Ignition switch ON |
4.5 to 5.5 V |
|
C142-103(PTA) - C142-79(EPTA) |
No. 2 turbo pressure sensor signal |
Idling with warm engine |
1.0 to 4.5 V |
|
C142-102(THTA) - A139-10(E1) |
Intake air temperature sensor (No. 2 turbo pressure sensor) signal |
Idling with warm engine |
0 to 5.25 V |
|
C142-50(#30) - A139-10(E1) |
Port fuel injector assembly signal (No. 3 cylinder) |
Idling with warm engine (Data List item "Injection Mode" displaying "Port") |
Pulse generation (See waveform 20) |
|
C142-51(#20) - A139-10(E1) |
Port fuel injector assembly signal (No. 2 cylinder) |
Idling with warm engine (Data List item "Injection Mode" displaying "Port") |
Pulse generation (See waveform 20) |
|
C142-52(#10) - A139-10(E1) |
Port fuel injector assembly signal (No. 1 cylinder) |
Idling with warm engine (Data List item "Injection Mode" displaying "Port") |
Pulse generation (See waveform 20) |
|
C142-21(WGV+) - A139-10(E1) |
Vacuum regulating valve assembly operation signal |
Vacuum regulating valve assembly operating |
Pulse generation |
|
C142-22(WGV-) - A139-10(E1) |
Vacuum regulating valve assembly operation signal |
Vacuum regulating valve assembly operating |
Pulse generation |
WAVEFORM 1
CAN Communication Signal (Reference)
|
ECM Terminal Name |
Between CANH and E1 Between CANU and E1 |
|
Tester Range |
1 V/DIV., 10 μs./DIV. |
|
Condition |
Engine stopped, ignition switch ON |
HINT:
The waveform varies depending on the CAN communication signal.
WAVEFORM 2
Engine Speed Signal
|
ECM Terminal Name |
Between NEO and E1 |
|
Tester Range |
5 V/DIV., 2 ms./DIV. |
|
Condition |
Idling with warm engine |
HINT:
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 3
CAN Communication Signal (Reference)
|
ECM Terminal Name |
Between CANL and E1 Between CAND and E1 |
|
Tester Range |
1 V/DIV., 10 μs./DIV. |
|
Condition |
Engine stopped, ignition switch ON |
HINT:
The waveform varies depending on the CAN communication signal.
WAVEFORM 4
Cooling Fan Control Signal
|
ECM Terminal Name |
Between RFC and E1 |
|
Tester Range |
1 V/DIV., 20 ms/DIV. |
|
Condition |
Ignition switch ON, A/C switch on (max cool) |
HINT:
The duty ratio varies depending on the engine coolant temperature.
WAVEFORM 5
Vehicle Speed Signal
|
ECM Terminal Name |
Between SPD and E1 |
|
Tester Range |
2 V/DIV., 20 ms./DIV. |
|
Condition |
Driving at 20 km/h (12 mph) |
HINT:
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 6
Throttle Actuator Operation Signal (Negative Terminal)
|
ECM Terminal Name |
Between M- and E1 |
|
Tester Range |
5 V/DIV., 1 ms./DIV. |
|
Condition |
Idling with warm engine |
HINT:
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 7
Throttle Actuator Operation Signal (Positive Terminal)
|
ECM Terminal Name |
Between M+ and E1 |
|
Tester Range |
5 V/DIV., 1 ms./DIV. |
|
Condition |
Idling with warm engine |
HINT:
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 8
Air Fuel Ratio Sensor Heater Operation Signal
|
ECM Terminal Name |
Between HA1A and E1 Between HA1B and E1 |
|
Tester Range |
5 V/DIV., 10 ms./DIV. |
|
Condition |
Idling with cold engine |
WAVEFORM 9
No. 1 (to No. 3) Fuel Injector Assembly Signal
|
ECM Terminal Name |
CH1: Between #1D+ and E1 CH2: Between #1D- and E1 |
|
CH1: Between #2D+ and E1 CH2: Between #2D- and E1 |
|
|
CH1: Between #3D+ and E1 CH2: Between #3D- and E1 |
|
|
Tester Range |
50 V/DIV., 200 μs./DIV. |
|
Condition |
Idling with warm engine. |
WAVEFORM 10
Fuel Pump Assembly (for High Pressure Side) Signal
|
ECM Terminal Name |
CH1: Between FP1+ and E1 CH2: Between FP1- and E1 |
|
Tester Range |
20 V/DIV., 500 μs./DIV. |
|
Condition |
Idling with warm engine, Data List item "Injection Mode" displaying "Direct" |
WAVEFORM 11
Cam Timing Oil Control Solenoid Assembly Operation Signal
|
ECM Terminal Name |
Between OC1+ and OC1- Between OE1+ and OE1- |
|
Tester Range |
5 V/DIV., 1 ms./DIV. |
|
Condition |
Idling |
WAVEFORM 12
Purge VSV Operation Signal
|
ECM Terminal Name |
Between PRG and E1 |
|
Tester Range |
10 V/DIV., 20 ms./DIV. |
|
Condition |
Idling with warm engine, under purge control |
HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 13
Transmission Revolution Sensor Signal
|
ECM Terminal Name |
Between NIMO and E1 |
|
Tester Range |
1 V/DIV., 2 ms./DIV. |
|
Condition |
Engine idling and clutch pedal fully released |
WAVEFORM 14
Ignition Coil Assembly Signal (IGT Signal)
|
ECM Terminal Name |
Between IGT (1 to 3) and E1 |
|
Tester Range |
2.5 V/DIV, 20 ms/DIV |
|
Condition |
Idling with warm engine |
HINT:
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 15
LIN Communication Signal (Reference)
|
ECM Terminal Name |
Between LIN and E1 |
|
Tester Range |
2 V/DIV., 10 ms./DIV. |
|
Condition |
Idling with warm engine |
WAVEFORM 16
Camshaft Position Sensor Signal
|
ECM Terminal Name |
CH1: Between VV1+ and VV1- CH2: Between EV1+ and EV1- |
|
Tester Range |
5 V/DIV., 20 ms./DIV. |
|
Condition |
Idling with warm engine |
HINT:
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 17
Crankshaft Position Sensor Signal
|
ECM Terminal Name |
Between NE+ and NE- |
|
Tester Range |
2 V/DIV., 20 ms./DIV. |
|
Condition |
Idling with warm engine |
HINT:
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 18
Mass Air Flow Meter Sub-assembly Signal
|
ECM Terminal Name |
Between VG and E2G |
|
Tester Range |
1 V/DIV., 100 μs./DIV. |
|
Condition |
Ignition switch ON |
WAVEFORM 19
Knock Control Sensor Signal
|
ECM Terminal Name |
Between KNK1 and EKNK |
|
Tester Range |
1 V/DIV., 1 ms./DIV. |
|
Condition |
Engine speed maintained at 4000 rpm after warming up the engine |
HINT:
- The wavelength becomes shorter as the engine speed increases.
- The waveforms and amplitudes displayed differ slightly depending on the vehicle.
WAVEFORM 20
Port Fuel Injector Assembly Signal
|
ECM Terminal Name |
Between #10 (to #30) and E1 |
|
Tester Range |
20 V/DIV., 20 ms./DIV. |
|
Condition |
Idling with warm engine (Data List item "Injection Mode" displaying "Port") |
HINT:
- The wavelength becomes shorter as the engine speed increases.
- When the port injection injectors are operating, Port is displayed for Injection Mode of the Data List.
|
|