METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for Gasoline Model): B150013; Fuel Sender Circuit Open; 2022 MY Corolla Corolla Hatchback GR Corolla [06/2021 - 09/2022]

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001XA15
Model Year Start: 2022	Model: GR Corolla	Prod Date Range: [06/2021 - 09/2022]
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (for Gasoline Model): B150013; Fuel Sender Circuit Open; 2022 MY Corolla Corolla Hatchback GR Corolla [06/2021 - 09/2022]

DTC

B150013

Fuel Sender Circuit Open

DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B150013

Fuel Sender Circuit Open

Diagnosis Condition:

The ignition switch is ON
IG power source voltage is 9.5 V or more

Malfunction Status:

Voltage signal from fuel sender gauge assembly is 0.2 V or less
Voltage signal from fuel sender gauge assembly is 4.7 V or more

Malfunction Time:

10 seconds or more

Harness or connector
Fuel sender gauge assembly
Fuel suction tube with pump and gauge assembly
Combination meter assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

PROCEDURE

1.	CONFIRM MODEL

(a) Choose the model to be inspected.

Result	Proceed to
for M20A-FKS	A
for 2ZR-FAE	B

B

A

2.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Combination Meter / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Combination Meter > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Fuel Input	Fuel input	Min.: 0.00 L, Max.: 655.35 L or Unset	Fuel receiver gauge indicates F: 45.00 L Fuel receiver gauge indicates 3/4: 35.00 L Fuel receiver gauge indicates 1/2: 25.00 L Fuel receiver gauge indicates 1/4: 15.00 L Fuel receiver gauge indicates E: 5.00 L	-

Body Electrical > Combination Meter > Data List

Tester Display
Fuel Input

Result	Proceed to
Fuel level data can be displayed on the Techstream	A
Fuel level data cannot be displayed on the Techstream	B

A

REPLACE COMBINATION METER ASSEMBLY

B

3.	INSPECT FUEL SENDER GAUGE ASSEMBLY

(a) Remove the fuel sender gauge assembly.

w/ Canister Pump Module: Click here

w/o Canister Pump Module: Click here

(b) Inspect the fuel sender gauge assembly.

w/ Canister Pump Module: Click here

w/o Canister Pump Module: Click here

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

w/ Canister Pump Module: Click here

w/o Canister Pump Module: Click here

OK

4.	INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

*a	Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
O46-1 (FV) - A-3	Always	Below 1 Ω
O46-2 (FE) - A-2	Always	Below 1 Ω
O46-3 (FS) - A-1	Always	Below 1 Ω
O46-1 (FV) - O46-3 (FS) or A-3 - A-1	Always	10 kΩ or higher
O46-1 (FV) - O46-2 (FE) or A-3 - A-2	Always	10 kΩ or higher
O46-2 (FE) - O46-3 (FS) or A-2 - A-1	Always	10 kΩ or higher

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

w/ Canister Pump Module: Click here

w/o Canister Pump Module: Click here

OK

5.	CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the I4 combination meter assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
O46-1 (FV) - I4-14 (FV)	Always	Below 1 Ω
O46-3 (FS) - I4-31 (FR)	Always	Below 1 Ω
O46-2 (FE) - I4-24 (FE&B)	Always	Below 1 Ω
O46-1 (FV) or I4-14 (FV) - Body ground	Always	10 kΩ or higher
O46-3 (FS) or I4-31 (FR) - Body ground	Always	10 kΩ or higher

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Combination Meter / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Combination Meter > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Fuel Input	Fuel input	Min.: 0.00 L, Max.: 655.35 L or Unset	w/ Canister Pump Module Fuel receiver gauge indicates F: 45.00 L Fuel receiver gauge indicates 3/4: 35.00 L Fuel receiver gauge indicates 1/2: 25.00 L Fuel receiver gauge indicates 1/4: 15.00 L Fuel receiver gauge indicates E: 5.00 L w/o Canister Pump Module Fuel receiver gauge indicates F: 44.85 L Fuel receiver gauge indicates 3/4: 34.99 L Fuel receiver gauge indicates 1/2: 25.00 L Fuel receiver gauge indicates 1/4: 15.00 L Fuel receiver gauge indicates E: 5.00 L	-

Body Electrical > Combination Meter > Data List

Tester Display
Fuel Input

Result	Proceed to
Fuel level data can be displayed on the Techstream	A
Fuel level data cannot be displayed on the Techstream	B

A

REPLACE COMBINATION METER ASSEMBLY

B

7.	INSPECT FUEL SENDER GAUGE ASSEMBLY

(a) Remove the fuel sender gauge assembly.

w/ Canister Pump Module: Click here

w/o Canister Pump Module: Click here

(b) Inspect the fuel sender gauge assembly.

w/ Canister Pump Module: Click here

w/o Canister Pump Module: Click here

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

w/ Canister Pump Module: Click here

w/o Canister Pump Module: Click here

OK

8.	INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

*a	Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
O44-1 (FV) - A-3	Always	Below 1 Ω
O44-2 (FE) - A-2	Always	Below 1 Ω
O44-3 (FS) - A-1	Always	Below 1 Ω
O44-1 (FV) - O44-3 (FS) or A-3 - A-1	Always	10 kΩ or higher
O44-1 (FV) - O44-2 (FE) or A-3 - A-2	Always	10 kΩ or higher
O44-2 (FE) - O44-3 (FS) or A-2 - A-1	Always	10 kΩ or higher

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

w/ Canister Pump Module: Click here

w/o Canister Pump Module: Click here

OK

9.	CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the I4 combination meter assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
O44-1 (FV) - I4-14 (FV)	Always	Below 1 Ω
O44-3 (FS) - I4-31 (FR)	Always	Below 1 Ω
O44-2 (FE) - I4-24 (FE&B)	Always	Below 1 Ω
O44-1 (FV) or I4-14 (FV) - Body ground	Always	10 kΩ or higher
O44-3 (FS) or I4-31 (FR) - Body ground	Always	10 kΩ or higher

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR