LIGHTING (EXT): LIGHTING SYSTEM (for HV Model): DATA LIST / ACTIVE TEST; 2022 MY Corolla Corolla HV [06/2021

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001WSPD
Model Year Start: 2022	Model: Corolla	Prod Date Range: [06/2021 - 09/2022]
Title: LIGHTING (EXT): LIGHTING SYSTEM (for HV Model): DATA LIST / ACTIVE TEST; 2022 MY Corolla Corolla HV [06/2021 - 09/2022]

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Enter the following menus:

(1) for Main Body: Body Electrical / Main Body / Data List.

(2) for Steering Angle Sensor: Chassis / Steering Angle Sensor / Data List.

(3) for Combination Meter: Body Electrical / Combination Meter / Data List.

(4) for Front Recognition Camera (Front Lighting Control): Body Electrical / Front Recognition Camera (Front Lighting Control) / Data List.

(5) for Front Recognition Camera: Chassis / Front Recognition Camera / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Parking Brake SW	Parking brake switch signal	OFF or ON	OFF: Parking brake switch off ON: Parking brake switch on	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
Auto High Beam Main Switch	Auto high beam switch signal	OFF or ON	OFF: Auto high beam switch not pressed ON: Auto high beam switch pressed	w/ Automatic High Beam System
Head Light SW (Head)	Light control switch head position signal	OFF or ON	OFF: Light control switch not in head position ON: Light control switch in head position	-
Insolation Amount of Solar Sensor RH	Solar sensor RH condition	0 to 51100 or SensorFail	Condition can be displayed	-
Insolation Amount of Solar Sensor LH	Solar sensor LH condition	0 to 51100 or SensorFail	Condition can be displayed	-
Light Sensor Illuminance	Light control sensor illuminance	0 to 8191 lx or SensorFail	Value is output according to ambient light level	The displayed value is "0" when no light is detected.
AUTO Light Status	Auto light control operation status	Not AUTO or AUTO	Not AUTO: Automatic light control not operating AUTO: Automatic light control operating	-
AFS/AHS ECU High Beam Control	AFS (adaptive front-lighting system) or adaptive high beam system control function	Not Apply or Apply	Not Apply: AFS (adaptive front-lighting system) or adaptive high beam system control unavailable Apply: AFS (adaptive front-lighting system) or adaptive high beam system control valid	-
AFS/AHS ECU High Beam Light Status	AFS (adaptive front-lighting system) or adaptive high beam system high beam operation status	OFF or ON	OFF: AFS (adaptive front-lighting system) or adaptive high beam system high beam off ON: AFS (adaptive front-lighting system) or adaptive high beam system high beam on	-
Light Sensor Connection Status	Light control sensor connection status	OFF or ON	OFF: Automatic light control sensor has not been connected ON: Automatic light control sensor connected or has been connected	-
Headlight Lighting Function	ECU which controls the lighting system	Main Body or Lighting Sys ECU	Main Body: Lighting system controlled by main body ECU (multiplex network body ECU) Lighting Sys ECU: Lighting system is controlled by headlight ECU sub-assembly	-
Sensitivity	Sensitivity of the automatic light control system	Light2, Light1, Normal, Dark1 or Dark2	Customize setting displayed	-
DRL Function	Setting of the DRL function on/off	OFF or ON	Customize setting displayed	for vehicles with customize setting "DRL Function"
Headlight in Conjunction with Wiper	Wiper-linked low beam headlight control	OFF or ON	Customize setting displayed	-
Disp Ex ON Sen	Ambient brightness level required to dim display lights (combination meter, navigation display, etc.)	Light2, Light1, Normal, Dark1 or Dark2	Customize setting displayed	-
Disp Ex OFF Sen	Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.)	Light2, Light1, Normal, Dark1 or Dark2	Customize setting displayed	-
Light Auto OFF Delay	Light auto OFF delay	Off, 30 s, 60 s or 90 s	Customize setting displayed	-
Auto H Beam STS0	Automatic high beam sensor current state	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed*	If the value of this item is not as specified, the automatic high beam sensor system may be malfunctioning. w/ Automatic High Beam System
Auto H Beam STS1	Automatic high beam sensor state past 1	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed*	Although this item is displayed on the Techstream, it is not applicable to this vehicle. w/ Automatic High Beam System
Auto H Beam STS2	Automatic high beam sensor state past 2	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed*	Although this item is displayed on the Techstream, it is not applicable to this vehicle. w/ Automatic High Beam System
Auto H Beam STS3	Automatic high beam sensor state past 3	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed*	Although this item is displayed on the Techstream, it is not applicable to this vehicle. w/ Automatic High Beam System
Auto H Beam STS4	Automatic high beam sensor state past 4	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed*	Although this item is displayed on the Techstream, it is not applicable to this vehicle. w/ Automatic High Beam System
Auto H Beam STS5	Automatic high beam sensor state past 5	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed*	Although this item is displayed on the Techstream, it is not applicable to this vehicle. w/ Automatic High Beam System
Auto H Beam STS6	Automatic high beam sensor state past 6	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed*	Although this item is displayed on the Techstream, it is not applicable to this vehicle. w/ Automatic High Beam System
Auto H Beam STS7	Automatic high beam sensor state past 7	Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err	Condition can be displayed*	Although this item is displayed on the Techstream, it is not applicable to this vehicle. w/ Automatic High Beam System
Extended Headlight Lighting	Extended headlight lighting time	30 s, 60 s, 90 s or 120 s	Customize setting displayed	w/ Extended Headlight Lighting System
Tail Remind Buzzer Function	Setting of the tail remind buzzer function on/off	OFF or ON	Customize setting displayed	-
The Number of DTC	Number of trouble codes	0 to 255	Number of stored DTCs displayed	-

HINT:

*: The details of each value of the Range are as follows:

Display Value	Condition	Control Condition	Diagnostic Note
Undetec	Automatic high beam sensor being initialized	Control suspended (low beam headlights illuminated)	-
CAM NA	Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc.	Control suspended (previous beam setting maintained)	-
No sens	No lights detected	High beam headlights illuminated	Only when vehicle speed within operation speed range
Hlight	Headlights of oncoming vehicle, etc. detected	Low beam headlights illuminated	Only when vehicle speed within operation speed range
Taillgt	Taillights preceding vehicle, etc. detected	Low beam headlights illuminated	Only when vehicle speed within operation speed range
Speed	No lights detected and vehicle speed below operation speed	Low beam headlights illuminated	-
Daytime	Bright light detected	Low beam headlights illuminated	-
Village	Streetlights, etc. detected	Low beam headlights illuminated	Only when vehicle speed within operation speed range
Delay	Changing between low beams and high beams	Changing between low beams and high beams	Only when vehicle speed within operation speed range
SAE Mod	Not applicable	-	-
Malfunc
Aim Lmt
Undefin
LIN Err

Chassis > Steering Angle Sensor > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Light OFF Switch	Light control switch DRL OFF1 or off2 position signal	OFF or ON	OFF: Light control switch not in DRL OFF1 or off2 position ON: Light control switch in DRL OFF1 or off2 position	1, 2
Auto Light Switch	Light control switch AUTO position signal	OFF or ON	OFF: Light control switch not in AUTO position ON: Light control switch in AUTO position	-
Head Light Switch (Tail)	Light control switch tail position signal	OFF or ON	OFF: Light control switch in neither tail nor head position ON: Light control switch in tail or head position	-
Head Light Switch (Head)	Light control switch head position signal	OFF or ON	OFF: Light control switch not in head position ON: Light control switch in head position	-
High Beam Main Switch	Dimmer switch high position signal	OFF or ON	OFF: Dimmer switch not in high position ON: Dimmer switch in high position	-
Passing Light Switch	Dimmer switch high flash position (pass) signal	OFF or ON	OFF: Dimmer switch not in high flash position ON: Dimmer switch in high flash position	-
Auto High Beam Main Switch	Auto high beam switch signal	OFF or ON	OFF: Auto high beam switch off ON: Auto high beam switch on	Although the item is displayed on the Techstream, it is not applicable to the vehicle.
Turn Signal Switch (Right)	Turn signal switch (right turn position) signal	OFF or ON	OFF: Turn signal switch not in right turn position ON: Turn signal switch in right turn position	-
Turn Signal Switch (Left)	Turn signal switch (left turn position) signal	OFF or ON	OFF: Turn signal switch not in left turn position ON: Turn signal switch in left turn position	-
Cornering Light/Front Side Illuminate Light Switch	Turn signal switch (full turn) signal	OFF or ON	OFF: Turn signal switch not in left or right turn position ON: Turn signal switch in left or right full turn position	-
Front Fog Light Switch	Front fog light switch signal	OFF or ON	OFF: Front fog light switch off ON: Front fog light switch on	Although the item is displayed on the Techstream, it is not applicable to the vehicle.
Rear Fog Light/Bad Weather Switch	Rear fog light switch signal	OFF or ON	OFF: Rear fog light switch off ON: Rear fog light switch on	Although the item is displayed on the Techstream, it is not applicable to the vehicle.
Automatic Light Equipped Info	Automatic light control system specification information	Unknown, With or Without	Unknown: Specification not stored With: Automatic light control system equipped Without: Automatic light control system not equipped	-
Bad Weather Mode Equipped Info	Bad weather specification information	Unknown, Without or With	Unknown: Specification not stored Without: Bad weather specification not equipped With: Bad weather specification equipped	Although the item is displayed on the Techstream, it is not applicable to the vehicle.
The Number of DTCs	Number of trouble codes	0 to 255	Number of stored DTCs displayed	-

*1: w/ DRL OFF Switch
*2: w/ OFF Switch

Body Electrical > Combination Meter > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Turn Signal Switch (Left)	Turn signal switch (left) signal	OFF or ON	OFF: Turn signal switch not in left turn position ON: Turn signal switch in left turn position	Although the item is displayed on the Techstream, it is not applicable to the vehicle.
Turn Signal Switch (Right)	Turn signal switch (right) signal	OFF or ON	OFF: Turn signal switch not in right turn position ON: Turn signal switch in right turn position	Although the item is displayed on the Techstream, it is not applicable to the vehicle.
Turn Switch Signal (Full Turn)	Turn signal switch (full turn) signal	OFF or ON	OFF: Turn signal switch not in left or right turn position ON: Turn signal switch in left or right turn position	Although the item is displayed on the Techstream, it is not applicable to the vehicle.
Hazard Flasher Switch	Hazard warning signal switch signal	OFF or ON	OFF: Hazard warning signal switch off ON: Hazard warning signal switch on	-
Lane Change Flashing Times Adjust	Condition of the lane change flashing times	OFF, 3, 4, 5, 6 or 7	Customize setting displayed	-

Body Electrical > Front Recognition Camera (Front Lighting Control) > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Actual driven distance

0 to 16777215

Roughly the same as the actual driven distance

w/ Automatic High Beam System

Total Distance Traveled - Unit

Actual driven distance unit

km or mile

Displays the current actual driven distance unit

w/ Automatic High Beam System

AHB/AHS Information

Automatic high beam system or adaptive high beam system specification information

Unknown, AHB or AHS

Unknown: Specification not stored

AHB: w/ Automatic High Beam System

AHS: w/ Adaptive High Beam System

w/ Automatic High Beam System

Chassis > Front Recognition Camera > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Front Recognition Camera High Temperature 2

Forward recognition camera condition

Not High Temperature or High Temperature

Not High Temperature: 65°C (149°F) or lower

High Temperature: 65°C (149°F) or higher

When "High Temperature" is displayed, the automatic high beam system is temporarily suspended.
w/ Automatic High Beam System

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(d) Enter the following menus:

(1) for Main Body: Body Electrical / Main Body / Active Test.

(2) for Combination Meter: Body Electrical / Combination Meter / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Daytime Running Light	Daytime running lights	OFF or ON	-
Taillight Relay	Taillight relay	OFF or ON	-
Headlight Relay	Low beam headlights	OFF or ON	-
Head Light Hi	High beam headlights	OFF or ON	-
Front Fog Light Relay	Front fog lights	OFF or ON	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
Rear Fog Light Relay	Rear fog lights	OFF or ON	Although this item is displayed on the Techstream, it is not applicable to this vehicle.
Dimmer Signal	Dimmer signal	OFF or ON	State where circumference illumination is bright
Automatic High Beam Switch Light	Auto high beam switch indicator light	OFF or ON	w/ Automatic High Beam System

Body Electrical > Combination Meter > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Multi Display All (White)	Multi-information display (White display)	ON	-