EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Rear Door): REMOVAL; 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2020

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000001PHIB
Model Year Start: 2021	Model: GR Corolla	Prod Date Range: [06/2020 - 09/2022]
Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Rear Door): REMOVAL; 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2020 - 09/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane Control System
		Pre-collision System
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock	Power Door Lock Control System (for Hatchback)
Rear door glass sub-assembly Rear door glass run Rear door inner glass weatherstrip	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here

3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Click here

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

6. REMOVE REAR SPEAKER ASSEMBLY

Click here

7. REMOVE REAR DOOR FRAME GARNISH

Click here

8. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here

9. REMOVE REAR DOOR PANEL PROTECTOR

Click here

10. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

11. REMOVE REAR DOOR GLASS RUN

Click here

12. DISCONNECT REAR DOOR WEATHERSTRIP

Click here

13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Click here

14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

15. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP WITH REAR DOOR QUARTER WINDOW GLASS

Click here

16. REMOVE REAR DOOR OUTSIDE STRIPE

HINT:

When removing the rear door outside stripe, heat the vehicle body and rear door outside stripe using a heat light.

Heating Temperature

Item	Temperature
Rear Door Outside Stripe and Vehicle Body	40 to 60°C (104 to 140°F)

CAUTION:

Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

*a	Heated Part
*b	Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the rear door outside stripe and vehicle body.

(b) Pull back on one of the ends of the rear door outside stripe to remove it.

HINT:

When pulling on the rear door outside stripe, pull it parallel to the vehicle body.