Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001P7E3 |
Model Year Start: 2021 |
Model: GR Corolla |
Prod Date Range: [06/2020 - 09/2022] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: REAR SEAT SIDE AIRBAG ASSEMBLY: REMOVAL; 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2020 - 09/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative auxiliary battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock*1
|
Power Door Lock Control System
|
|
NOTICE:
for HV Model:
-
After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))
for Gasoline Model:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
for HV Model: Click here
for TMC Made Gasoline Model: Click here
for TMMMS Made: Click here
NOTICE:
After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
3. REMOVE REAR SEAT HEADREST ASSEMBLY (w/ Removable Headrest)
Click here
4. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY (for Hatchback RH Side)
Click here
5. DISCONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY
Click here
6. REMOVE REAR SEATBACK ASSEMBLY LH (for LH Side)
Click here
7. REMOVE REAR SEATBACK ASSEMBLY RH (for RH Side)
Click here
8. REMOVE REAR SEAT CUSHION ASSEMBLY
for HV Model: Click here
for Gasoline Model: Click here
9. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
10. REMOVE REAR DOOR SCUFF PLATE
for Sedan (for HV Model): Click here
for Sedan (for Gasoline Model): Click here
for Hatchback: Click here
11. REMOVE REAR UNDER SIDE COVER (for HV Model)
Click here
12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
HINT:
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear seat side garnish.
13. REMOVE REAR SEAT SIDE GARNISH
for Sedan: Click here
for Hatchback: Click here
14. REMOVE REAR SEAT AIRBAG ASSEMBLY
CAUTION:
When storing the rear seat airbag assembly, keep the airbag deployment side facing upward.
|
Deployment Side
|
(a) Check that the ignition switch (for Gasoline Model) or power switch (for HV Model) is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Remove the 2 bolts.
*a
|
Protective Tape
|
*b
|
Airbag Connector
|
*c
|
Airbag Connector Locking Button
|
|
Release in this Direction
|
(d) Disengage the clip and separate the rear seat airbag assembly.
NOTICE:
When separating the rear seat airbag assembly, do not pull the airbag wire harness.
(e) Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.
(f) Disconnect the airbag connector to remove the rear seat airbag assembly.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
|