Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001P5SW |
Model Year Start: 2021 |
Model: GR Corolla |
Prod Date Range: [06/2020 - 09/2022] |
Title: INTERIOR PANELS / TRIM: ROOF HEADLINING (for Hatchback): INSTALLATION; 2021 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2020 - 09/2022] |
INSTALLATION
PROCEDURE
1. INSTALL ROOF HEADLINING ASSEMBLY
(a) Put the roof headlining assembly back into the vehicle through the back door as shown in the illustration.
NOTICE:
Do not damage the roof headlining assembly or vehicle interior.
|
Install in this Direction
|
(b) Install the roof headlining assembly with the 3 clips.
(c) Engage the 2 claws to install the base of each visor holder.
(d) Install the visor holder as shown in the illustration.
|
Install in this Direction
|
HINT:
Use the same procedure for the LH side and RH side.
(e) for Rear Pillar RH Side:
(1) Connect the 2 connectors.
(2) Engage the guide.
(3) Connect the connector bracket with the bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(4) Engage the clamp.
(f) for Front Pillar RH Side:
(1) Remove the protective cover.
(2) Connect each connector.
(3) Engage the 3 clamps.
(4) Install the protective cover.
(g) for Front Pillar LH Side:
(1) Remove the protective cover.
(2) Connect the 2 connectors.
(3) Engage the 4 clamps.
(4) Install the protective cover.
(h) for Windshield Glass Side:
(1) Connect the 2 connectors.
2. INSTALL VISOR ASSEMBLY LH
(a) Set the visor assembly LH into place by aligning it with the connector and screw fastening hole.
|
Install in this Direction
|
NOTICE:
-
Make sure to install the visor assembly LH with its arrow facing the front of the vehicle.
-
When setting the part into place, move it straight upward so as not to damage the connector.
-
Hold the visor assembly with one hand so that it does not drop.
(b) Connect the visor assembly LH to the visor holder.
(c) Install the visor assembly LH with the 2 screws.
3. INSTALL VISOR BRACKET COVER LH
(a) Engage the 4 claws to install the visor bracket cover LH.
4. INSTALL VISOR ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
5. INSTALL VISOR BRACKET COVER RH
HINT:
Use the same procedure as for the LH side.
6. INSTALL ASSIST GRIP SUB-ASSEMBLY
HINT:
Use the same procedure for all assist grip sub-assemblies.
(a) Install the 2 clips to the assist grip.
|
|
(b) Temporarily install the 2 assist grip covers to the assist grip as shown in the illustration.
(c) Engage the 2 clips to install the assist grip sub-assembly as shown in the illustration.
|
Install in this Direction
|
(d) Engage the 4 claws to install the assist grip cover LH and assist grip cover RH.
NOTICE:
Make sure that the clips are engaged securely.
|
|
7. INSTALL REAR ASSIST GRIP ASSEMBLY LH
HINT:
Use the same procedure as for the assist grip sub-assembly.
8. INSTALL REAR ASSIST GRIP ASSEMBLY RH
HINT:
Use the same procedure as for the assist grip sub-assembly.
9. INSTALL NO. 1 FORWARD RECOGNITION COVER
Click here
10. INSTALL NO. 2 FORWARD RECOGNITION COVER
Click here
11. INSTALL VANITY LIGHT ASSEMBLY
Click here
12. INSTALL NO. 1 ROOM LIGHT ASSEMBLY
Click here
13. INSTALL MAP LIGHT ASSEMBLY
Click here
14. INSTALL ROOF SIDE INNER GARNISH LH
(a) Pass the anchor of the rear 3 point type seat outer belt assembly LH through the roof side inner garnish LH.
(b) Engage the 9 clips to install the roof side inner garnish LH as shown in the illustration.
|
Install in this Direction
|
-
|
-
|
HINT:
Engage the clip in the order shown in the illustration.
15. CONNECT REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY LH
Click here
16. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
(a) Engage the 2 clips and 3 claws.
(b) Install the deck trim side panel assembly LH with the 2 clips.
(c) Engage the guide.
|
|
*a
|
Ring of the Luggage Hold Belt Striker Assembly
|
|
|
(d) Install the luggage hold belt striker assembly with the bolt.
HINT:
Lift the ring of the luggage hold belt striker assembly as shown in the illustration.
17. INSTALL DECK TRIM SIDE LOWER BOARD LH (w/ Spare Tire)
(a) Engage the 4 claws to install the deck trim side lower board LH.
18. INSTALL REAR SEAT SIDE GARNISH LH
(a) Pass the rear seatback hinge sub-assembly LH through the rear seat side garnish LH as shown in the illustration.
*1
|
Rear Seatback Hinge Sub-assembly LH
|
|
Install in this Direction
|
(b) Engage the 4 guides and 8 claws to install the rear seat side garnish LH.
19. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
20. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Click here
21. CONNECT REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
22. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
23. INSTALL DECK TRIM SIDE LOWER BOARD RH (w/ Spare Tire)
HINT:
Use the same procedure as for the LH side.
24. INSTALL REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
25. INSTALL CENTER PILLAR UPPER GARNISH LH
(a) Pass the anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH.
(b) Engage the 2 guides (A) and clip as shown in the illustration.
*a
|
Guide (A)
|
*b
|
Guide (B)
|
|
Install in this Direction (1)
|
|
Install in this Direction (2)
|
(c) Engage the guide (B) as shown in the illustration.
(d) Install the center pillar upper garnish LH with the 2 clips.
26. INSTALL CENTER PILLAR LOWER GARNISH LH
(a) Engage the 4 claws and 3 clips to install the center pillar lower garnish LH as shown in the illustration.
|
Install in this Direction (1)
|
|
Install in this Direction (2)
|
27. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
28. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
Click here
29. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
30. INSTALL REAR DOOR SCUFF PLATE LH
(a) Engage the 2 guides and 7 claws to install the rear door scuff plate LH.
HINT:
Install the center pillar lower garnish LH side of the rear door scuff plate LH first.
|
|
31. INSTALL FRONT PILLAR GARNISH LH
(a) Remove the protective cover.
(b) Install 2 new front pillar garnish clips to the front pillar garnish LH.
HINT:
Make sure that the front pillar garnish clip is engaged correctly.
|
|
*1
|
Front Pillar Garnish Clip
|
*2
|
Front Pillar Garnish LH
|
|
|
(c) w/o Front No. 3 Speaker:
(1) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.
|
Install in this Direction
|
(d) w/ Front No. 3 Speaker:
(1) Connect the connector.
(2) Push the front pillar garnish LH as shown in the illustration to engage the 2 guides.
(e) Engage the 2 front pillar garnish clips to install the front pillar garnish LH as shown in the illustration.
HINT:
Make sure that the curtain shield airbag assembly LH is not pinched.
|
Install in this Direction
|
(f) Remove the protective tape.
32. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
33. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
(a) Engage the 2 clips as shown in the illustration.
|
Install in this Direction
|
(b) Install the cowl side trim sub-assembly LH with the clip.
34. INSTALL FRONT DOOR SCUFF PLATE LH
(a) Engage the 2 guides and 8 claws to install the front door scuff plate LH.
HINT:
Install the center pillar lower garnish LH side of the front door scuff plate LH first.
|
|
35. INSTALL CENTER PILLAR UPPER GARNISH RH
HINT:
Use the same procedure as for the LH side.
36. INSTALL CENTER PILLAR LOWER GARNISH RH
HINT:
Use the same procedure as for the LH side.
37. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
38. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
HINT:
Use the same procedure as for the LH side.
39. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
40. INSTALL REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
41. INSTALL FRONT PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
43. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
44. INSTALL FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
45. INSTALL REAR SEAT ASSEMBLY
Click here
46. INSTALL REAR DECK TRIM COVER (w/o Spare Tire)
(a) Engage the 4 guides, 4 clips and 4 claws to install the rear deck trim cover.
(b) Engage the 2 guides.
(c) Install the 2 luggage hold belt striker assemblies with the 2 bolts.
47. INSTALL REAR FLOOR MAT ASSEMBLY (w/o Spare Tire)
(a) Install the rear floor mat assembly.
48. INSTALL REAR DECK TRIM COVER (w/ Spare Tire)
(a) Engage the 4 guides, 4 clips and 4 claws to install the rear deck trim cover.
(b) Engage the 2 guides.
(c) Install the 2 luggage hold belt striker assemblies with the 2 bolts.
49. INSTALL FRONT DECK FLOOR BOX (w/ Spare Tire)
(a) Engage the 2 clips.
(b) Install the front deck floor box with the 2 bolts.
50. INSTALL REAR NO. 1 FLOOR BOARD (w/ Spare Tire)
(a) Engage the 7 clips to install the rear No. 1 floor board.
51. INSTALL DECK FLOOR BOX RH (w/ Spare Tire)
(a) Install the deck floor box RH with the clip.
52. INSTALL DECK FLOOR BOX LH (w/ Spare Tire)
(a) Install the deck floor box LH with the clip.
53. INSTALL DECK BOARD ASSEMBLY (w/ Spare Tire)
(a) Install the deck board assembly.
54. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
(a) Install the package tray trim panel assembly.
|