INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE

1. INSTALL REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY LH

(a) Secure the outer belt anchor bracket sub-assembly LH in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.

(b) Engage the 2 guides.

(c) Temporarily install the rear 3 point type seat outer belt assembly LH to the outer belt anchor bracket sub-assembly LH with the nut.

(d) Fully tighten the nut to install the rear 3 point type seat outer belt assembly LH.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

2. INSTALL REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

3. INSTALL REAR SEAT BELT RETRACTOR COVER LH

(a) Install the rear seat belt retractor cover LH.

4. INSTALL REAR SEAT BELT RETRACTOR COVER RH

HINT:

Use the same procedure as for the LH side.

5. INSTALL REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY LH WITH BRACKET

(a) Engage the guide and temporarily install the rear 3 point type seat outer belt assembly LH with bracket with the 2 bolts.

(b) Fully tighten the bolt (A) and then the bolt (B) to install the rear 3 point type seat outer belt assembly LH with bracket. Torque: Bolt (A) : 12.5 N·m {127 kgf·cm, 9 ft·lbf} Bolt (B) : 42 N·m {428 kgf·cm, 31 ft·lbf}

(c) Check that the ELR locks.

(1) With the rear 3 point type seat outer belt assembly LH with bracket installed to the vehicle, check that the belt locks when it is pulled out quickly.

NOTICE:

This check should be performed with the rear 3 point type seat outer belt assembly LH with bracket installed to the vehicle.

(d) Install the floor anchor of the rear 3 point type seat outer belt assembly LH with the bolt.

Torque:

42 N·m {428 kgf·cm, 31 ft·lbf}

NOTICE:

Do not allow the anchor part of the rear 3 point type seat outer belt assembly LH to overlap the protruding parts of the floor panel.

Protruding Part

6. INSTALL REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY RH WITH BRACKET

HINT:

Use the same procedure as for the LH side.

7. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

(a) Engage the 5 guides.

(b) Install the package tray trim panel assembly with the 3 clips.

8. INSTALL REAR SEAT SHOULDER BELT HOLE COVER

(a) Engage the 2 guides and 2 claws to install the rear seat shoulder belt hole cover.

9. INSTALL PACKAGE TRAY TRIM BRACKET LH

(a) Engage the 4 claws and 3 clips to install the package tray trim bracket LH.

10. INSTALL PACKAGE TRAY TRIM BRACKET RH

HINT:

Use the same procedure as for the LH side.

11. INSTALL CENTER STOP LIGHT SET

Click here

12. INSTALL ROOF SIDE INNER GARNISH LH

Click here

13. INSTALL ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.

14. INSTALL REAR SEAT SIDE GARNISH LH (w/o Rear Seat Side Airbag)

Click here

15. INSTALL REAR SEAT SIDE GARNISH LH (w/ Rear Seat Side Airbag)

Click here

16. INSTALL REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

17. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

18. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

19. INSTALL REAR DOOR SCUFF PLATE LH (for Gasoline Model)

Click here

20. INSTALL REAR DOOR SCUFF PLATE RH (for Gasoline Model)

HINT:

Use the same procedure as for the LH side.

21. INSTALL REAR UNDER SIDE COVER LH (for HV Model)

Click here

22. INSTALL REAR UNDER SIDE COVER RH (for HV Model)

HINT:

Use the same procedure as for the LH side.

23. INSTALL REAR DOOR SCUFF PLATE LH (for HV Model)

Click here

24. INSTALL REAR DOOR SCUFF PLATE RH (for HV Model)

HINT:

Use the same procedure as for the LH side.

25. INSTALL REAR SEAT ASSEMBLY

Click here