Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001NMQ9
Model Year Start: 2021 Model: Corolla Prod Date Range: [04/2020 - 09/2022]
Title: 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: P06579E; Actuator Supply Voltage "A" Stuck On; 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]

DTC

P06579E

Actuator Supply Voltage "A" Stuck On

MONITOR DESCRIPTION

The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is functioning properly. The output voltage is usually 0 V when the power switch is turned off. If the output voltage is 7 V or higher when the power switch is turned off, the ECM will illuminate the MIL and store this DTC when the power switch is turned on (IG).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P06579E

Actuator Supply Voltage "A" Stuck On

A throttle actuator power supply error (1 trip detection logic).

ECM

Comes on

DTC stored
  • SAE Code: P0657
  • DTC for Mexico Models: Applies

MONITOR STRATEGY

Related DTCs

P0657: Electronic throttle actuator supply voltage circuit performance

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

Throttle actuator

Frequency of Operation

Once per driving cycle

Duration

1 second

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

Both of the following conditions are met

-

Auxiliary battery voltage

8 V or higher

Command to electronic throttle actuator power

Off

TYPICAL MALFUNCTION THRESHOLDS

Electronic throttle actuator power supply voltage

7 V or higher

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the Techstream off.
  6. Turn the power switch off.
  7. Disconnect the Techstream.
  8. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
  9. Connect the cable to the negative (-) auxiliary battery terminal.
  10. Turn the power switch on (IG) [A].
  11. Wait 10 seconds or more.
  12. Turn the power switch off [B].
  13. Wait 15 seconds or more.
  14. Connect the Techstream to the DLC3.
  15. Turn the power switch on (IG).
  16. Turn the Techstream on.
  17. Wait 5 seconds or more [C].
  18. Enter the following menus: Powertrain / Engine / Trouble Codes [D].
  19. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  20. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  21. Input the DTC: P06579E.
  22. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, perform steps [B] through [D] again.
    • [A] to [D]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

NOTICE:

  • Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

    - for Nickel Metal Hydride Battery: Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY

    - for Lithium-ion Battery: Click here 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with P610): VEHICLE CONTROL HISTORY

    (Select Powertrain in Health Check and then check the time stamp data.)

    Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; 2ZR-FXE (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

    - for Nickel Metal Hydride Battery: Click here 2020 - 2022 MY Corolla Corolla HV [01/2019 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for NICKEL METAL HYDRIDE BATTERY): VEHICLE CONTROL HISTORY

    - for Lithium-ion Battery: Click here 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with P610): VEHICLE CONTROL HISTORY

  • After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the power switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the power switch off.

NEXT

2.

READ OUTPUT DTC (DTC P06579E)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

(c) Turn the power switch on (IG).

(d) Wait 10 seconds or more.

(e) Turn the power switch off.

(f) Wait 15 seconds or more.

(g) Connect the Techstream to the DLC3.

(h) Turn the power switch on (IG).

(i) Turn the Techstream on.

(j) Wait 5 seconds or more.

(k) Enter the following menus: Powertrain / Engine / Trouble Codes.

(l) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P06579E is output

B
A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM