Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001N3ZQ
Model Year Start: 2021 Model: Corolla Prod Date Range: [04/2020 - 09/2022]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with P610): P1C6A9F; Motor Shutdown Stuck Off; 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]

DTC

P1C6A9F

Motor Shutdown Stuck Off

DTC SUMMARY

MALFUNCTION DESCRIPTION

The hybrid vehicle control ECU detects malfunctions which prevent the motor (MG2) inverter shutdown circuit shutting down the hybrid vehicle control system. Detection is performed during the shutdown sequence when the power switch is turned off. If motor (MG2) inverter operation is detected after a shutdown signal was sent to the motor (MG2) inverter, the hybrid vehicle control ECU will determine that there is a malfunction and store this DTC.

The cause of this malfunction may be the following:

Inverter with converter assembly SDWN (MG2) internal circuit malfunction

  • Inverter with converter assembly malfunction

DESCRIPTION

The motor generator control ECU (MG ECU) sends shutdown signals to the inverter to cut the power supply to the generator (MG1) and motor (MG2). If the power switch is turned off, the motor generator control ECU (MG ECU) will send a GSDN (MG1 Shutdown Signal) signal and MSDN (MG2 shutdown signal) signal to check the function of the HV gate block. If a shutdown malfunction is detected, this DTC will be stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P1C6A9F

Motor Shutdown Stuck Off

When the HV gate block function check is performed (when the power switch is turned from on (READY) to off), the MSDN (MG2 shutdown) signal is sent but the motor (MG2) inverter current and voltage (VH) do not decrease.

(1 trip detection logic)

Inverter with converter assembly

Does not come on

Master Warning: Comes on

Related Data List

DTC No.

Data List

P1C6A9F
  • Ready Signal
  • VH-Voltage after Boosting

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with P610): UTILITY

  1. Connect the Techstream to the DLC3.
  2. Turn the power switch on (IG) and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the power switch off and wait for 2 minutes or more.
  5. Turn the power switch on (READY) and wait for 30 seconds or more.
  6. Turn the power switch off and wait for 2 minutes or more.
  7. Turn the power switch on (IG) and turn the Techstream on.
  8. Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
  9. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.

PROCEDURE

1.

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

Click here 2021 - 2022 MY Corolla Corolla HV [04/2020 - 09/2022]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with P610): DTC CHECK / CLEAR

NEXT

END